You can change the format in Google earth to match anything. Jon Langeler Michwave Technologies, Inc.
> On Aug 17, 2017, at 10:19 AM, Chuck McCown <[email protected]> wrote: > > Yeah, but it is decimal coordinates. I discovered if you click a placemark > in GE then decimal coordinates will come up that can be cut and pasted into > UBNT. But after going through all that, I really didn’t see where it was > better than RM and actually RM is better than airlink in some respects. > > From: Josh Reynolds > Sent: Thursday, August 17, 2017 8:12 AM > To: [email protected] > Subject: Re: [AFMUG] AF-11x > > Look under the selected radios on the right side. There are GPS coordinates > boxes right below height and EIRP that say "AP Location" and "Station > Location". > >> On Aug 17, 2017 8:47 AM, "Chuck McCown" <[email protected]> wrote: >> Is there an easy way to drop a location from Google Earth or RM into airlink? >> >> From: Josh Reynolds >> Sent: Tuesday, August 15, 2017 1:00 PM >> To: [email protected] >> Subject: Re: [AFMUG] AF-11x >> >> airlink.ubnt.com >> >> Click on "AirFiber fx" line on the right side in the middle, then 11 GHz. >> Rest is self explanatory. >> >>> On Aug 15, 2017 1:59 PM, "Chuck McCown" <[email protected]> wrote: >>> Link does not work. >>> >>> From: Josh Reynolds >>> Sent: Tuesday, August 15, 2017 12:56 PM >>> To: [email protected] >>> Subject: Re: [AFMUG] AF-11x >>> >>> https://airline.ubnt.com is pretty damn good these days. Should help you >>> figure out what you need easily. >>> >>> It does require you to log in with your account. >>> >>>> On Aug 15, 2017 1:34 PM, "Chuck McCown" <[email protected]> wrote: >>>> What is a common channel BW? 40 MHz? I suppose it depends on congestion. >>>> I only need about 250 Mbps so lower order modulation may be desirable and >>>> perhaps narrower channels too. >>>> >>>> From: Jeremy >>>> Sent: Tuesday, August 15, 2017 10:54 AM >>>> To: [email protected] >>>> Subject: Re: [AFMUG] AF-11x >>>> >>>> Of course, the exact configuration is based on your license and which >>>> frequencies it is supposed to operate on. The above configuration is just >>>> an example. >>>> >>>>> On Tue, Aug 15, 2017 at 10:53 AM, Jeremy <[email protected]> wrote: >>>>> They are like that, but 3x bigger. On top, the lid comes off and the >>>>> duplexers go beneath the cover. If your link is 'High' then you will >>>>> want 'High' duplexers for both sides of the link (x4 total - two extra to >>>>> purchase) - they will go in a configuration like 1-3-3-1 on one side and >>>>> 3-1-1-3 on the other side. >>>>> >>>>>> On Tue, Aug 15, 2017 at 10:11 AM, Mathew Howard <[email protected]> >>>>>> wrote: >>>>>> They come with 1 duplexer (setup for SISO) - you need to buy the second >>>>>> one separately to do MIMO. You do need to figure out what frequencies >>>>>> you're going to be using before you buy the radios, since there are two >>>>>> different duplexers, depending on which half of the band you're in. >>>>>> You need one frequency pair on both polarities (for MIMO). >>>>>> >>>>>>> On Tue, Aug 15, 2017 at 10:52 AM, Chuck McCown <[email protected]> wrote: >>>>>>> Do they all come with two N connectors or do you have to pay more for >>>>>>> duplexers? Not quite sure how to buy or license. I guess you have to >>>>>>> have two pairs of frequencies? Or at the very least, both >>>>>>> polarizations on the same frequency? >>>>>>> >>>>>>> Trying to collect some budgetary estimates on what my project is going >>>>>>> to cost.
