Sounds like a winner. Then have 1 or more lid options Jon Langeler Michwave Technologies, Inc.
> On Aug 20, 2017, at 5:56 PM, Chuck McCown <[email protected]> wrote: > > I was making handhole components a few years ago. Not a big money maker. > But handholes are simply too expensive. I came up with some alternate > designs, like a slice of 36” plastic conduit. Made a lid to go over it. > Maybe I ought to revisit that project. The world needs lower cost hand > holes. > > From: George Skorup > Sent: Sunday, August 20, 2017 12:46 PM > To: [email protected] > Subject: Re: [AFMUG] Aerial fiber $/mile > > We're looking at doing a neighborhood where we have wireless now. Private > association of about 40 homes. The president is also an electrical contractor > and has helped us on other non-fiber stuff in the past. So at least we can > get duct at his cost. Looking like about 6250 feet of duct and 21 or 22 > handholes. Probably going to follow Chuck Hogg's strategy with 1x4 PLCs in > the splice cases fed by PLCs at the cabinet. My rough guestimates are around > $25-27k before putting it in the ground or customer drops. We figure we can > make a business case with a $1k install. > >> On 8/20/2017 12:31 PM, Jason McKemie wrote: >> It does include the fiber, but not electronics or splice closures. Just >> fiber, associated mounting hardware, and guy wires/anchors. >> >>> On Saturday, August 19, 2017, Adam Moffett <[email protected]> wrote: >>> Drops were anywhere from 150' to 1600'. The long ones naturally pushed up >>> the average quite a bit. >>> >>> On the feed down the road it's $1.80/foot plus the cable. The contractor >>> is supplying all material except the cable itself and honestlyI don't >>> recall how much of that was labor vs material. We did have to add 4 poles, >>> so there's that in the $17,000/mile. And that also includes splice >>> enclosures, switches, optics, switch enclosure, and electric installation >>> at the switch enclosure. >>> >>> Does your $1/ft in materials include the actual fiber? If not, then we're >>> very close. If it does then I have to sharpen the pencil quite a bit. >>> >>> >>> >>> ------ Original Message ------ >>> From: "Jason McKemie" <[email protected]> >>> To: "javascript:_e(%7B%7D,'cvml','[email protected]');" >>> <javascript:_e(%7B%7D,'cvml','[email protected]');> >>> Sent: 8/19/2017 3:49:07 PM >>> Subject: Re: [AFMUG] Aerial fiber $/mile >>> >>>> How long are the drops? Labor for main runs cost me about $.75/ft last >>>> time I did it, plus around $1/ft in materials. I didn't have to do much >>>> make ready though, that can add up quickly. I think my drops cost me >>>> roughly $1/ft since I'm doing them myself now. >>>> >>>>> On Saturday, August 19, 2017, Adam Moffett >>>>> <javascript:_e(%7B%7D,'cvml','[email protected]');> wrote: >>>>> I'm at $17,000 per mile on a recent active E deployment. Each customer >>>>> installation averaged $900. This is rural, so lots of long drops. >>>>> >>>>> I guess I'm looking over to the next stall to see how mine measures up to >>>>> yours. >>>>> >>>>> >>>>> ------ Original Message ------ >>>>> From: "Adam Moffett" <[email protected]> >>>>> To: "[email protected]" <[email protected]> >>>>> Sent: 8/19/2017 9:55:20 AM >>>>> Subject: [AFMUG] Aerial fiber $/mile >>>>> >>>>>> So after the dust has settled on completed projects, what sort of money >>>>>> have you ended up spending per mile? >>>>>> How much per customer installation? >
