Chuck,
PLC splitter in spice case doing full fusion splicing.
--
Best regards,
Mark mailto:m...@mailmt.com
Myakka Technologies, Inc.
www.MyakkaTech.com
------
Monday, February 12, 2018, 12:09:32 PM, you wrote:
Are you using splitters in splice cases or in cross connect boxes?
From: Mark - Myakka Technologies
Sent: Monday, February 12, 2018 9:55 AM
To: Adam Moffett
Subject: Re: [AFMUG] Outdoor PON OLT
Adam,
There are some ranging things you have to consider. "The requirement
when deploying ONTs are the maximum distance between two ONTs cannot
exceed 20Km."
The way we have done this is to reuse fibers as we travel down long
stretches of roads between neighborhoods.
We will deploy a 1x32 splitter in the field. We will splice that into
the last 3 ribbons/tubes of our fiber. Example, if we were using a 144
count cable, ribbons 10-12 will be spliced into. After a few miles
depending on density or distance, we will splice in another 1x32
splitter to ribbons 10-12. We just keep doing this until we run out of
light budget.
We build to the lots passed, so we are not trying to optimize max usage
per port. Currently, we average about 50% utilization on our ports.
--
Best regards,
Mark mailto:m...@mailmt.com
Myakka Technologies, Inc.
www.MyakkaTech.com
------
Monday, February 12, 2018, 11:38:39 AM, you wrote:
Maybe I need to review the math.
I was figuring on several small splitters along the route. I didn't
compare to a 1x32 in the cabinet because I figured if I brought every
fiber back to the cabinet then I didn't save anything versus ethernet.
------ Original Message ------
From: "Mark - Myakka Technologies" <m...@mailmt.com>
To: "Adam Moffett" <af@afmug.com>
Sent: 2/12/2018 11:30:46 AM
Subject: Re: [AFMUG] Outdoor PON OLT
Adam,
How far are you going? We are pushing almost 20 miles on a 1x32 split.
Are you using one 1x32 or multiple smaller splitters?
--
Best regards,
Mark mailto:m...@mailmt.com
Myakka Technologies, Inc.
www.MyakkaTech.com
------
Sunday, February 11, 2018, 10:24:30 PM, you wrote:
I'm looking at rural areas (like a few houses per mile). As I'm
looking at hypothetical power budgets for PON, I'm finding that if I
run the line down the road and put splitters on the pole I can split
5-6 times and then I'm getting too low on db to keep going down the
road. At 5 or so houses per port, a 1U, 8 port ONT is no denser than a
1U switch.
Your stated reasons for PON are all correct. The numbers just aren't
seeming to work out for me.
I also figure if I install enough fibers for AE, I can still switch to
PON some day if I want to.
We would never max out the PON port, but looking back on the past 15
years of growth in consumption I wonder if I should ever say "never".
In AE I can put 100Gig in every house if I have to. I'll "never" have
to do that as far as I can imagine, but my imagination could be
limited.
-Adam
------ Original Message ------
From: "Josh Reynolds" <j...@kyneticwifi.com>
To: af@afmug.com
Sent: 2/11/2018 9:28:34 PM
Subject: Re: [AFMUG] Outdoor PON OLT
A few reasons...
Port cost is still fairly high.
More splicing.
More fiber required.
Larger chassis required.
More power required.
More battery backup required.
Consumers not even close to using up 1-2 generations back of PON
capacity in most places.
On Sun, Feb 11, 2018 at 7:53 PM, Chuck McCown <ch...@wbmfg.com> wrote:
So, why do PON and not active in these super cheap optics days?
From: Chuck Hogg
Sent: Sunday, February 11, 2018 6:10 PM
To: af@afmug.com
Subject: Re: [AFMUG] Outdoor PON OLT
We are walking away from them and Alphion...I think Mark's product with
Zhone is different.
Regards,
Chuck
On Sun, Feb 11, 2018 at 2:29 PM, Mike Hammett <af...@ics-il.net> wrote:
I think Chuck Hogg walked far away from DASAN... or maybe it was DASAN
that rescued them from the one they walked far away form. I don't
remember which. ;-)
-----
Mike Hammett
Intelligent Computing Solutions <http://www.ics-il.com/>
Midwest Internet Exchange <http://www.midwest-ix.com/>
The Brothers WISP <http://www.thebrotherswisp.com/>
--------------------------------------------------------------------------------
From: "Jason McKemie" <j.mcke...@veloxinetbroadband.com>
To: af@afmug.com
Sent: Tuesday, February 6, 2018 4:35:53 PM
Subject: [AFMUG] Outdoor PON OLT
In light of finding out that Calix's offering is not going to be
anywhere near within budget, does anyone else have any other
suggestions?
I found these guys, but have never heard of them:
http://www.richerlink.com/en/products.asp?ClassID=116
It looks like DASAN also has an option - I've at least heard of them:
http://www.dasannetworks.com/product_images/V5806_20140520174927.pdf
-Jason