I went the unistrut route and it seemed to work fine. Just used lags since
this chimney was vinyl-siding-covered-wood on the outside.

On Thursday, May 17, 2018, Rory Conaway <r...@triadwireless.net> wrote:

> We use the wall anchor pins with Unistrut and then just clamp to the
> pipe.  Drill a hole for the pin, tap it down with a washer to expand it and
> they lock solid.
>
>
>
> rory
>
>
>
> *From:* Af [mailto:af-boun...@afmug.com] *On Behalf Of *Dave
> *Sent:* Thursday, May 17, 2018 9:57 AM
> *To:* af@afmug.com
> *Subject:* Re: [AFMUG] Attaching pole to Chimney
>
>
>
> So long as they dont use pine logs should be ok :)
>
> On 05/15/2018 07:04 PM, ch...@wbmfg.com wrote:
>
> Stick a piece of PVC down the chimney and use spray foam to hold it in
> place.
>
>
>
> *From:* Jason McKemie
>
> *Sent:* Tuesday, May 15, 2018 5:28 PM
>
> *To:* af@afmug.com
>
> *Subject:* Re: [AFMUG] Attaching pole to Chimney
>
>
>
> Do the unistrut conduit clamps hold the conduit tightly enough to mount it
> vertically? I thought they were intended for horizontal runs.
>
> On Tuesday, May 15, 2018, Sam Lambie <samtaos...@gmail.com> wrote:
>
> Unistrut, clamps and EMT. Done
>
>
>
> On Tue, May 15, 2018 at 2:46 PM, Jason McKemie <
> j.mcke...@veloxinetbroadband.com> wrote:
>
> It's just a wood box covered in vinyl.
>
>
>
> On Tue, May 15, 2018 at 3:08 PM, Josh Luthman <j...@imaginenetworksllc.com>
> wrote:
>
> The chimney has vinyl?  I assume it's brick behind it?
>
>
>
> If you have to get it from the local hardware store, go there and see what
> all can work.  I'd probably look for the best tool rather than limit myself
> to that one store, though.
>
>
>
>
> Josh Luthman
> Office: 937-552-2340
> Direct: 937-552-2343
> 1100 Wayne St
> <https://maps.google.com/?q=1100+Wayne+St+Suite+1337+Troy,+OH+45373&entry=gmail&source=g>
> Suite 1337
> <https://maps.google.com/?q=1100+Wayne+St+Suite+1337+Troy,+OH+45373&entry=gmail&source=g>
> Troy, OH 45373
> <https://maps.google.com/?q=1100+Wayne+St+Suite+1337+Troy,+OH+45373&entry=gmail&source=g>
>
>
>
> On Tue, May 15, 2018 at 3:07 PM, Jason McKemie <
> j.mcke...@veloxinetbroadband.com> wrote:
>
> Anyone have any advice as to what hardware I can use to attach a 6'
> section of 1.5" emt to a chimney? It's the vinyl siding covered type. I was
> thinking of just drilling it and running lags straight through, but a
> bracket of some type, possibly utilizing pipe clamps, would be preferred.
> I'll need to source it from a local hardware store.
>
>
>
>
>
>
>
>
>
> --
>
> --
> *Sam Lambie*
> Taosnet Wireless Tech.
> 575-758-7598 Office
> www.Taosnet.com <http://www.newmex.com>
>
>
>
> --
>

Reply via email to