First I don't like the 6 line cord. Use an rj11 2 wire cord, but watch the crossover vrs straight on the old red and green.
Next the interrupt must be fixed. Do this in the CMOS before you boot. Go to the PCI bus assignments and set the IRQ or go and disable the serial ports thereby allowing irq 3 and 4 to be assigned. :) Paul -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mr. James W. Laferriere Sent: Wednesday, October 26, 2005 7:53 PM To: [email protected] Subject: [Asterisk-Users] x100p (FXO) not being seen by asterisk (is my bestguess) . Hello All , I installed a x100p clone device in a system . I pulled (Wed, 26 Oct 2005 early am) cvs & compiled & installed for a 2.6 kernel . We call this system 'test' . This system is a HP Vectra with a 933MHZ processor . Test has all the z* modules installed (*1). and can see the x100p (ie *2) . The other system has been operational for some time . I have a ata-186 responding to two numbers 21 & 22 . I attached a 6 line cord between the ata-186 port 22 & the 'line' side of the x100p . I have configured the 3 necessary files (*3) . Now when I call 22 from an ipphone the x100p does not pickup the line . All it does is ring . I have to be missing something here . Tia , JimL ps: Here is one problem I have yet been unable to resolv . I am unable to move the x100p to some other IRQ & at present it is sharing irq 9 with the SMBus . Anyone know how to work around this ? 00:1f.3 SMBus: Intel Corporation 82801AA SMBus (rev 02) Subsystem: Intel Corporation 82801AA SMBus Flags: medium devsel, IRQ 9 I/O ports at 1810 [size=16] 01:02.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device 8085:0003 Flags: bus master, medium devsel, latency 64, IRQ 9 I/O ports at 2000 [size=256] Memory at ec100000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 (*1) # modprobe -vl /lib/modules/2.6.13.2/misc/ztdynamic.ko /lib/modules/2.6.13.2/misc/ztdummy.ko /lib/modules/2.6.13.2/misc/ztd-loc.ko /lib/modules/2.6.13.2/misc/ztd-eth.ko /lib/modules/2.6.13.2/misc/zaptel.ko /lib/modules/2.6.13.2/misc/wcusb.ko /lib/modules/2.6.13.2/misc/wcte11xp.ko /lib/modules/2.6.13.2/misc/wctdm.ko /lib/modules/2.6.13.2/misc/wct4xxp.ko /lib/modules/2.6.13.2/misc/wct1xxp.ko /lib/modules/2.6.13.2/misc/wcfxo.ko /lib/modules/2.6.13.2/misc/torisa.ko /lib/modules/2.6.13.2/misc/tor2.ko /lib/modules/2.6.13.2/misc/pciradio.ko (*2) # cat /proc/zaptel/1 Span 1: WCFXO/0 "Wildcard X101P Board 1" 1 WCFXO/0/0 FXSKS (*3) # cat /etc/zaptel.conf fxsks=1 loadzone=us defaultzone=us # cat /etc/asterisk/zapata.conf [trunkgroups] [channels] ;language=en signalling=fxs_ks context=x100p-incoming ;usecallerid=yes ;hidecallerid=no ;callwaiting=no ;threewaycalling=yes ;transfer=yes ;echocancel=yes ;echotraining=yes channel => 1 # cat /etc/asterisk/zapata.conf ...snip... [x100p-incoming] ; incoming calls from the FXO port are directed to this context from zapata.conf exten => s,1,Answer exten => s,2,Echo -- +------------------------------------------------------------------+ | James W. Laferriere | System Techniques | Give me VMS | | Network Engineer | 3542 Broken Yoke Dr. | Give me Linux | | [EMAIL PROTECTED] | Billings , MT. 59105 | only on AXP | +------------------------------------------------------------------+ _______________________________________________ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list [email protected] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
