Hi Simon, Thanks for getting back.
I am going to try that from sipsak.... Could this be somehow sent via AMI also using perl or php? Elliott > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On > Behalf Of Simon P. Ditner > Sent: Thursday, October 30, 2008 10:40 PM > To: Elliott Jeyaseelan > Cc: Toronto Asterisk UG > Subject: Re: [on-asterisk] Polycom 3.1 firmware pop-up > notification on phones display > > I would likely use "sipsak", which is a command line tool for > crafting sip messages. It says in that PDF that only warning > codes 300 to 399 are supported. > 399 is the generic warning parameter (see the SIP RFC3261, > section 20.43 on 'Warning'), so it would likely go something > like this (I have not tried it yet): > > sip endpoint: [EMAIL PROTECTED]:5060 > sip endpoint password: abc123 > sip server: 192.168.0.20:5060 > > 192.168.0.100 > > ---- > echo 'NOTIFY sip:[EMAIL PROTECTED]:5060 SIP/2.0 > > Via: SIP/2.0/UDP 192.168.0.20 > From: <sip:[EMAIL PROTECTED]> > To: <sip:[EMAIL PROTECTED]> > Warning: 399 192.168.0.20 "The sky is falling" > Date: blah > Call-ID: [EMAIL PROTECTED] > CSeq: 1300 NOTIFY > Contact: <sip:[EMAIL PROTECTED]> > Content-Length: 0 > ' | sipsak -v -f - -s sip:[EMAIL PROTECTED]:5060 -G -a abc123 > ---- > > On Thu, Oct 30, 2008 at 12:04 PM, Elliott Jeyaseelan > <[EMAIL PROTECTED]> wrote: > > Anyone? > > > >> -----Original Message----- > >> From: Elliott Jeyaseelan [mailto:[EMAIL PROTECTED] > >> Sent: Sunday, October 26, 2008 2:07 PM > >> To: Toronto Asterisk UG > >> Subject: [on-asterisk] Polycom 3.1 firmware pop-up notification on > >> phones display > >> > >> Hi, > >> > >> I was going thru the new 3.1 series of polycom firmware for the > >> soundpoint series IP phones, (301/501/550 etc) and on page 4-72 of > >> the Sip 3.1 administrators guide, there is a very short > blurp about > >> how to display a 3 second notification on the polycom > phone's display > >> via sip header. > >> > >> Has any tried this or have a clue on how to do this from > asterisk 1.4? > >> > >> The pdf can be viewed from the following link if anyone is > interested > >> in checking this out, I would be very interested to know > how to put > >> up a server generated message on the phones display sent from > >> asterisk either triggered by an event, time or other: > >> > >> http://www.polycom.com/common/documents/support/setup_maintena > >> nce/produc > >> ts/voice/spip_ssip_Admin_Guide_SIP_3_1.pdf > >> > >> Thanks for any suggestions or ideas. > >> > >> Elliott > >> > >> > --------------------------------------------------------------------- > >> To unsubscribe, e-mail: [EMAIL PROTECTED] For additional > >> commands, e-mail: [EMAIL PROTECTED] > >> > >> > >> > > > > > --------------------------------------------------------------------- > > To unsubscribe, e-mail: [EMAIL PROTECTED] For additional > > commands, e-mail: [EMAIL PROTECTED] > > > > > > > > -- > | It ain't what you don't know that gets you into trouble. It's what > | you know for sure that just ain't so. -- Mark Twain > | > | The Toronto Asterisk Users Group > | Join the discussion group by visiting http://taug.ca > > --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
