Hi Elliott, This isn't exactly what you asked for but I think the Polycom supports an API.
This presentation doesn't contain technical details but it's a good overview of the capabilities. http://www.voipevent.eu/pdf/voipevent2008_eindhoven/Polycom%20IP%20Handset%20Applications%20Overview.pdf I'm sure there's detailed API documentation available somewhere. Dave On Fri, Oct 31, 2008 at 12:24 PM, Elliott Jeyaseelan <[EMAIL PROTECTED]> wrote: > Hi Simon, > > Thanks for getting back. > > I am going to try that from sipsak.... > > Could this be somehow sent via AMI also using perl or php? > > Elliott > > > >> -----Original Message----- >> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On >> Behalf Of Simon P. Ditner >> Sent: Thursday, October 30, 2008 10:40 PM >> To: Elliott Jeyaseelan >> Cc: Toronto Asterisk UG >> Subject: Re: [on-asterisk] Polycom 3.1 firmware pop-up >> notification on phones display >> >> I would likely use "sipsak", which is a command line tool for >> crafting sip messages. It says in that PDF that only warning >> codes 300 to 399 are supported. >> 399 is the generic warning parameter (see the SIP RFC3261, >> section 20.43 on 'Warning'), so it would likely go something >> like this (I have not tried it yet): >> >> sip endpoint: [EMAIL PROTECTED]:5060 >> sip endpoint password: abc123 >> sip server: 192.168.0.20:5060 >> >> 192.168.0.100 >> >> ---- >> echo 'NOTIFY sip:[EMAIL PROTECTED]:5060 SIP/2.0 >> >> Via: SIP/2.0/UDP 192.168.0.20 >> From: <sip:[EMAIL PROTECTED]> >> To: <sip:[EMAIL PROTECTED]> >> Warning: 399 192.168.0.20 "The sky is falling" >> Date: blah >> Call-ID: [EMAIL PROTECTED] >> CSeq: 1300 NOTIFY >> Contact: <sip:[EMAIL PROTECTED]> >> Content-Length: 0 >> ' | sipsak -v -f - -s sip:[EMAIL PROTECTED]:5060 -G -a abc123 >> ---- >> >> On Thu, Oct 30, 2008 at 12:04 PM, Elliott Jeyaseelan >> <[EMAIL PROTECTED]> wrote: >> > Anyone? >> > >> >> -----Original Message----- >> >> From: Elliott Jeyaseelan [mailto:[EMAIL PROTECTED] >> >> Sent: Sunday, October 26, 2008 2:07 PM >> >> To: Toronto Asterisk UG >> >> Subject: [on-asterisk] Polycom 3.1 firmware pop-up notification on >> >> phones display >> >> >> >> Hi, >> >> >> >> I was going thru the new 3.1 series of polycom firmware for the >> >> soundpoint series IP phones, (301/501/550 etc) and on page 4-72 of >> >> the Sip 3.1 administrators guide, there is a very short >> blurp about >> >> how to display a 3 second notification on the polycom >> phone's display >> >> via sip header. >> >> >> >> Has any tried this or have a clue on how to do this from >> asterisk 1.4? >> >> >> >> The pdf can be viewed from the following link if anyone is >> interested >> >> in checking this out, I would be very interested to know >> how to put >> >> up a server generated message on the phones display sent from >> >> asterisk either triggered by an event, time or other: >> >> >> >> http://www.polycom.com/common/documents/support/setup_maintena >> >> nce/produc >> >> ts/voice/spip_ssip_Admin_Guide_SIP_3_1.pdf >> >> >> >> Thanks for any suggestions or ideas. >> >> >> >> Elliott >> >> >> >> >> --------------------------------------------------------------------- >> >> To unsubscribe, e-mail: [EMAIL PROTECTED] For additional >> >> commands, e-mail: [EMAIL PROTECTED] >> >> >> >> >> >> >> > >> > >> --------------------------------------------------------------------- >> > To unsubscribe, e-mail: [EMAIL PROTECTED] For additional >> > commands, e-mail: [EMAIL PROTECTED] >> > >> > >> >> >> >> -- >> | It ain't what you don't know that gets you into trouble. It's what >> | you know for sure that just ain't so. -- Mark Twain >> | >> | The Toronto Asterisk Users Group >> | Join the discussion group by visiting http://taug.ca >> >> > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
