Dave, Very interesting.
I would love to check out the api's assuming they are publicly available, somehow doubt that. Thanks for sharing this. Elliott > -----Original Message----- > From: Dave Donovan [mailto:[EMAIL PROTECTED] > Sent: Friday, October 31, 2008 3:34 PM > To: Toronto Asterisk UG > Subject: Re: [on-asterisk] Polycom 3.1 firmware pop-up > notification on phones display > > Hi Elliott, > > This isn't exactly what you asked for but I think the Polycom > supports an API. > > This presentation doesn't contain technical details but it's > a good overview of the capabilities. > > http://www.voipevent.eu/pdf/voipevent2008_eindhoven/Polycom%20 > IP%20Handset%20Applications%20Overview.pdf > > I'm sure there's detailed API documentation available somewhere. > > Dave > > On Fri, Oct 31, 2008 at 12:24 PM, Elliott Jeyaseelan > <[EMAIL PROTECTED]> wrote: > > Hi Simon, > > > > Thanks for getting back. > > > > I am going to try that from sipsak.... > > > > Could this be somehow sent via AMI also using perl or php? > > > > Elliott > > > > > > > >> -----Original Message----- > >> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of > >> Simon P. Ditner > >> Sent: Thursday, October 30, 2008 10:40 PM > >> To: Elliott Jeyaseelan > >> Cc: Toronto Asterisk UG > >> Subject: Re: [on-asterisk] Polycom 3.1 firmware pop-up > notification > >> on phones display > >> > >> I would likely use "sipsak", which is a command line tool for > >> crafting sip messages. It says in that PDF that only warning codes > >> 300 to 399 are supported. > >> 399 is the generic warning parameter (see the SIP RFC3261, section > >> 20.43 on 'Warning'), so it would likely go something like this (I > >> have not tried it yet): > >> > >> sip endpoint: [EMAIL PROTECTED]:5060 > >> sip endpoint password: abc123 > >> sip server: 192.168.0.20:5060 > >> > >> 192.168.0.100 > >> > >> ---- > >> echo 'NOTIFY sip:[EMAIL PROTECTED]:5060 SIP/2.0 > >> > >> Via: SIP/2.0/UDP 192.168.0.20 > >> From: <sip:[EMAIL PROTECTED]> > >> To: <sip:[EMAIL PROTECTED]> > >> Warning: 399 192.168.0.20 "The sky is falling" > >> Date: blah > >> Call-ID: [EMAIL PROTECTED] > >> CSeq: 1300 NOTIFY > >> Contact: <sip:[EMAIL PROTECTED]> > >> Content-Length: 0 > >> ' | sipsak -v -f - -s sip:[EMAIL PROTECTED]:5060 -G -a abc123 > >> ---- > >> > >> On Thu, Oct 30, 2008 at 12:04 PM, Elliott Jeyaseelan > <[EMAIL PROTECTED]> > >> wrote: > >> > Anyone? > >> > > >> >> -----Original Message----- > >> >> From: Elliott Jeyaseelan [mailto:[EMAIL PROTECTED] > >> >> Sent: Sunday, October 26, 2008 2:07 PM > >> >> To: Toronto Asterisk UG > >> >> Subject: [on-asterisk] Polycom 3.1 firmware pop-up > notification on > >> >> phones display > >> >> > >> >> Hi, > >> >> > >> >> I was going thru the new 3.1 series of polycom firmware for the > >> >> soundpoint series IP phones, (301/501/550 etc) and on > page 4-72 of > >> >> the Sip 3.1 administrators guide, there is a very short > >> blurp about > >> >> how to display a 3 second notification on the polycom > >> phone's display > >> >> via sip header. > >> >> > >> >> Has any tried this or have a clue on how to do this from > >> asterisk 1.4? > >> >> > >> >> The pdf can be viewed from the following link if anyone is > >> interested > >> >> in checking this out, I would be very interested to know > >> how to put > >> >> up a server generated message on the phones display sent from > >> >> asterisk either triggered by an event, time or other: > >> >> > >> >> http://www.polycom.com/common/documents/support/setup_maintena > >> >> nce/produc > >> >> ts/voice/spip_ssip_Admin_Guide_SIP_3_1.pdf > >> >> > >> >> Thanks for any suggestions or ideas. > >> >> > >> >> Elliott > >> >> > >> >> > >> > --------------------------------------------------------------------- > >> >> To unsubscribe, e-mail: [EMAIL PROTECTED] For > additional > >> >> commands, e-mail: [EMAIL PROTECTED] > >> >> > >> >> > >> >> > >> > > >> > > >> > --------------------------------------------------------------------- > >> > To unsubscribe, e-mail: [EMAIL PROTECTED] For > additional > >> > commands, e-mail: [EMAIL PROTECTED] > >> > > >> > > >> > >> > >> > >> -- > >> | It ain't what you don't know that gets you into trouble. > It's what > >> | you know for sure that just ain't so. -- Mark Twain > >> | > >> | The Toronto Asterisk Users Group > >> | Join the discussion group by visiting http://taug.ca > >> > >> > > > > > --------------------------------------------------------------------- > > To unsubscribe, e-mail: [EMAIL PROTECTED] For additional > > commands, e-mail: [EMAIL PROTECTED] > > > > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] For > additional commands, e-mail: [EMAIL PROTECTED] > > > --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
