i used "system->adminstration>Network" and i configurated everything from
there...and the clicking on "activate wlan0" for a while my access point
communicate and in the log i see that it's connected... here are outputs:
ah,in iwconfig there is IEEE 802.11g,my access point is b...could this be
the problem?
if i use NetworkManager i see it's connecting...but after a while i get the
message "disconnected"
[EMAIL PROTECTED] ~]# dmesg|grep b43
b43-phy0: Broadcom 4311 WLAN found
b43-phy0 debug: Found PHY: Analog 4, Type 2, Revision 8
b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
b43-phy0 debug: Adding Interface type 2
b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
b43-phy0 debug: Chip initialized
b43-phy0 debug: 32-bit DMA initialized
b43-phy0 debug: Wireless interface started
b43-phy0 debug: Removing Interface type 2
b43-phy0 debug: Wireless interface stopped
b43-phy0 debug: DMA-32 0x0200 (RX) max used slots: 1/64
b43-phy0 debug: DMA-32 0x02A0 (TX) max used slots: 0/128
b43-phy0 debug: DMA-32 0x0280 (TX) max used slots: 0/128
b43-phy0 debug: DMA-32 0x0260 (TX) max used slots: 0/128
b43-phy0 debug: DMA-32 0x0240 (TX) max used slots: 0/128
b43-phy0 debug: DMA-32 0x0220 (TX) max used slots: 10/128
b43-phy0 debug: DMA-32 0x0200 (TX) max used slots: 0/128
b43-phy0 debug: Adding Interface type 2
b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
b43-phy0 debug: Chip initialized
b43-phy0 debug: 32-bit DMA initialized
b43-phy0 debug: Wireless interface started
b43-phy0 debug: Removing Interface type 2
b43-phy0 debug: Wireless interface stopped
b43-phy0 debug: DMA-32 0x0200 (RX) max used slots: 1/64
b43-phy0 debug: DMA-32 0x02A0 (TX) max used slots: 0/128
b43-phy0 debug: DMA-32 0x0280 (TX) max used slots: 0/128
b43-phy0 debug: DMA-32 0x0260 (TX) max used slots: 0/128
b43-phy0 debug: DMA-32 0x0240 (TX) max used slots: 0/128
b43-phy0 debug: DMA-32 0x0220 (TX) max used slots: 6/128
b43-phy0 debug: DMA-32 0x0200 (TX) max used slots: 0/128
b43-phy0 debug: Adding Interface type 2
b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02)
b43-phy0 debug: Chip initialized
b43-phy0 debug: 32-bit DMA initialized
b43-phy0 debug: Wireless interface started
[EMAIL PROTECTED] ~]# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11g ESSID:"che12345"
Mode:Managed Frequency:2.462 GHz Access Point: 00:0C:41:19:2D:C1
Bit Rate=1 Mb/s Tx-Power=27 dBm
Retry min limit:7 RTS thr:off Fragment thr=2346 B
Encryption key:off
Link Quality=100/100 Signal level=-35 dBm Noise level=-38 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
[EMAIL PROTECTED] ~]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:16:D4:DF:6C:04
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:21
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:5847 errors:0 dropped:0 overruns:0 frame:0
TX packets:5847 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3271092 (3.1 MiB) TX bytes:3271092 (3.1 MiB)
wlan0 Link encap:Ethernet HWaddr 00:19:7E:84:F9:D3
inet addr:192.168.1.80 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::219:7eff:fe84:f9d3/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:1 errors:0 dropped:0 overruns:0 frame:0
TX packets:33 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:247 (247.0 b) TX bytes:5496 (5.3 KiB)
wmaster0 Link encap:UNSPEC HWaddr
00-19-7E-84-F9-D3-18-EF-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
[EMAIL PROTECTED] ~]# iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wmaster0 Interface doesn't support scanning.
wlan0 Scan completed :
Cell 01 - Address: 00:0C:41:19:2D:C1
ESSID:"che12345"
Mode:Master
Channel:11
Frequency:2.462 GHz (Channel 11)
Quality=98/100 Signal level=-36 dBm Noise level=-38
dBm
Encryption key:off
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s
Extra:tsf=000000001cad652f
thanks u all for helping
--
Io utilizzo la versione gratuita di SPAMfighter per utenti privati. Sino ad ora
ha rimosso 827 mail spam.
Gli utenti paganti non hanno questo messaggio nelle loro email .
Prova gratuitamente SPAMfighter qui:http://www.spamfighter.com/lit
_______________________________________________
Bcm43xx-dev mailing list
[email protected]
https://lists.berlios.de/mailman/listinfo/bcm43xx-dev
