> > *William:* > > *Assuming you are running Debian 8.x* > > *Try "shutdown -P now"* > > *--- Graham*
Graham, That might be ok if I wanted to halt the system, But what about when I want to reboot ? shutdown now -h has never had a problem in either case. For me at any rate. On Fri, Sep 25, 2015 at 9:22 AM, Graham <[email protected]> wrote: > William: > > Assuming you are running Debian 8.x > > Try "shutdown -P now" > > --- Graham > > == > > On Friday, September 25, 2015 at 11:09:38 AM UTC-5, Gerald wrote: >> >> >> On Fri, Sep 25, 2015 at 11:02 AM, William Hermans <[email protected]> >> wrote: >> >>> I'd be interested in fixing it, and sharing the info, but I do not know >>> where to start . . . >>> >>> On Fri, Sep 25, 2015 at 8:48 AM, Gerald Coley <[email protected]> >>> wrote: >>> >>>> The one needling RMA is the flashing power LED. The issue you describe >>>> does sounds like a SW issue of sorts, but is not one I have heard of that >>>> often. >>>> >>>> Gerald >>>> >>>> On Fri, Sep 25, 2015 at 10:25 AM, William Hermans <[email protected]> >>>> wrote: >>>> >>>>> Gerald, >>>>> >>>>> I actually have one of the boards that when issuing "shutdown now -r". >>>>> About 1 time in 3, the board will not power back up - Well, not properly >>>>> anyway. ethernet will continue blinking, power LED is on, but the USR LEDs >>>>> do not do their normal thing. Trying to ssh in, is futile. >>>>> >>>>> This same board, when using "reboot" has not shown these same >>>>> symptoms, and this is probably a software problem as I've noticed that it >>>>> has been getting worst over time. For instance, this would only happen >>>>> maybe 1 in 20 reboots a year or more ago. >>>>> >>>>> The board is an A5A . . . and yeah not going to RMA it, but I would >>>>> not mind testing . . . >>>>> >>>>> On Fri, Sep 25, 2015 at 6:34 AM, Gerald Coley <[email protected]> >>>>> wrote: >>>>> >>>>>> No testing needed. Request and RMA. >>>>>> >>>>>> http://www.elinux.org/Beagleboard:BeagleBoneBlack#RMA_Support >>>>>> >>>>>> >>>>>> Gerald >>>>>> >>>>>> On Fri, Sep 25, 2015 at 4:41 AM, <[email protected]> wrote: >>>>>> >>>>>>> Hello Everybody, >>>>>>> >>>>>>> >>>>>>> Yesterday I opened my BeagleBoneBlack (rev C) and started working >>>>>>> with it >>>>>>> >>>>>>> Today while I was trying accessing it trough SSH I got and error and >>>>>>> then I realized all the leds were off. >>>>>>> >>>>>>> Everytime I plug it back to the 5v adapter de PWR LED flash once and >>>>>>> the BeagleBone doesn't boot >>>>>>> >>>>>>> >>>>>>> I've been doing some research and I've found this link that >>>>>>> describes my problem. >>>>>>> >>>>>>> elinux.org/Beagleboard:BeagleBoneBlack >>>>>>> <http://elinux.org/Beagleboard:BeagleBoneBlack#Improper_Power_Down....All_Revisions> >>>>>>> >>>>>>> >>>>>>> Is there any other test that I should do? >>>>>>> >>>>>>> >>>>>>> Thanks in advance >>>>>>> >>>>>>> >>>>>>> PS: I tried to flash a Debian image again, but it just didn't boot >>>>>>> from the SD. >>>>>>> >>>>>>> -- >>>>>>> For more options, visit http://beagleboard.org/discuss >>>>>>> --- >>>>>>> You received this message because you are subscribed to the Google >>>>>>> Groups "BeagleBoard" group. >>>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>>> send an email to [email protected]. >>>>>>> For more options, visit https://groups.google.com/d/optout. >>>>>>> >>>>>> >>>>>> >>>>>> >>>>>> -- >>>>>> Gerald >>>>>> >>>>>> [email protected] >>>>>> http://beagleboard.org/ >>>>>> >>>>>> -- >>>>>> For more options, visit http://beagleboard.org/discuss >>>>>> --- >>>>>> You received this message because you are subscribed to the Google >>>>>> Groups "BeagleBoard" group. >>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>> send an email to [email protected]. >>>>>> For more options, visit https://groups.google.com/d/optout. >>>>>> >>>>> >>>>> -- >>>>> For more options, visit http://beagleboard.org/discuss >>>>> --- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "BeagleBoard" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send >>>>> an email to [email protected]. >>>>> For more options, visit https://groups.google.com/d/optout. >>>>> >>>> >>>> >>>> >>>> -- >>>> Gerald >>>> >>>> [email protected] >>>> http://beagleboard.org/ >>>> >>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to the Google >>>> Groups "BeagleBoard" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to [email protected]. >>>> For more options, visit https://groups.google.com/d/optout. >>>> >>> >>> -- >>> For more options, visit http://beagleboard.org/discuss >>> --- >>> You received this message because you are subscribed to the Google >>> Groups "BeagleBoard" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> For more options, visit https://groups.google.com/d/optout. >>> >> >> >> It may be something is not getting reset until power goes down. Try >> making sure all power rails are down before powering up again. >> Gerald >> >> [email protected] >> http://beagleboard.org/ >> > -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
