Here's the bootup log without the verbose mode flag enabled in uEnv.txt: **********************************************************************************
U-Boot SPL 2017.01-00360-gc604741cb3 (Aug 11 2017 - 15:47:09) DRA752-GP ES2.0 Trying to boot from MMC1 ** Unable to use mmc 0:1 for loading the env ** Using default environment U-Boot 2017.01-00360-gc604741cb3 (Aug 11 2017 - 15:47:09 -0500), Build: jenkins-github_Bootloader-Builder-592 CPU : DRA752-GP ES2.0 Model: TI AM5728 BeagleBoard-X15 Board: AM572x EVM REV A.3A DRAM: 2 GiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 ** Unable to use mmc 0:1 for loading the env ** Using default environment setup_board_eeprom_env: am57xx_evm_reva3 SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: <ethaddr> not set. Validating first E-fuse MAC cpsw Press SPACE to abort autoboot in 2 seconds usb_boot is currently disabled scsi_boot is currently disabled switch to partitions #0, OK mmc0 is current device Scanning mmc device 0 Checking for: /uEnv.txt ... Checking for: /boot/uEnv.txt ... 446 bytes read in 49 ms (8.8 KiB/s) Loaded environment from /boot/uEnv.txt Checking if uname_r is set in /boot/uEnv.txt ... debug: [uname_r=4.4.80-ti-r116] ... loading /boot/vmlinuz-4.4.80-ti-r116 ... 5487379 bytes read in 283 ms (18.5 MiB/s) debug: [console=ttyO2,115200n8 root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait coherent_pool=1M net.ifnames=0 quiet] ... debug: [bootz 0x82000000 0x88080000:53bb13 0x88000000] ... ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Ramdisk to 8fac4000, end 8ffffb13 ... OK Loading Device Tree to 8fa9c000, end 8fac3782 ... OK Starting kernel ... [ 0.063779] /cpus/cpu@0 missing clock-frequency property [ 0.063800] /cpus/cpu@1 missing clock-frequency property [ 2.194996] dra7-pcie 51000000.pcie_rc: link is not up [ 2.540811] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode [ 2.547225] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode [ 2.639312] omap_voltage_late_init: Voltage driver support not added [ 3.537309] remoteproc0: failed to load am57xx-pru1_0-fw [ 3.542894] remoteproc0: request_firmware failed: -2 [ 3.547988] pru-rproc 4b234000.pru0: rproc_boot failed [ 3.555830] remoteproc0: failed to load am57xx-pru1_1-fw [ 3.562347] remoteproc0: request_firmware failed: -2 [ 3.567442] pru-rproc 4b238000.pru1: rproc_boot failed [ 3.581573] remoteproc0: failed to load am57xx-pru2_0-fw [ 3.588946] remoteproc0: request_firmware failed: -2 [ 3.594048] pru-rproc 4b2b4000.pru0: rproc_boot failed [ 3.603674] remoteproc0: failed to load am57xx-pru2_1-fw [ 3.610193] remoteproc0: request_firmware failed: -2 [ 3.615285] pru-rproc 4b2b8000.pru1: rproc_boot failed [ 5.899545] remoteproc0: failed to load dra7-ipu1-fw.xem4 [ 5.923242] remoteproc2: failed to load dra7-dsp1-fw.xe66 [ 5.932697] remoteproc3: failed to load dra7-dsp2-fw.xe66 [ 6.517022] pixcir_ts 4-005c: pixcir_set_power_mode: can't read reg 0x33 : -121 [ 6.517027] pixcir_ts 4-005c: Failed to set IDLE mode Debian GNU/Linux 9 arm ttyS2 rcn-ee.net console Debian Image 2017-08-11 Support/FAQ: http://elinux.org/BeagleBoardDebian default username:password is [debian:temppwd] On Monday, August 14, 2017 at 9:17:48 AM UTC-5, Jeff Andich wrote: > > Hi Robert, > > So far, so good. It boots and gives the "arm" prompt. Will collect some > cursory logs and post them back up here.. > > Thanks and regards! > > Jeff > > > On Saturday, August 12, 2017 at 10:05:04 AM UTC-5, RobertCNelson wrote: >> >> Jeff, give this image a quick test: >> >> >> https://rcn-ee.net/rootfs/2017-08-11/microsd/bbx15-debian-9.1-console-armhf-2017-08-11-2gb.img.xz >> >> >> Regards, >> >> -- >> Robert Nelson >> https://rcn-ee.com/ >> > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/0945ff2e-3bff-4529-b7e7-20acd240c145%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
