Attached a text file containing log of output of the dmesg command.
*** Note: The dmesg command was captured from an earlier bootup session
than from the session with the abridged kernel log pasted above ***
Thanks! jeff
On Monday, August 14, 2017 at 10:15:26 AM UTC-5, Jeff Andich wrote:
>
> Here's the bootup log without the verbose mode flag enabled in uEnv.txt:
>
> **********************************************************************************
>
> U-Boot SPL 2017.01-00360-gc604741cb3 (Aug 11 2017 - 15:47:09)
> DRA752-GP ES2.0
> Trying to boot from MMC1
>
> ** Unable to use mmc 0:1 for loading the env **
> Using default environment
>
>
>
> U-Boot 2017.01-00360-gc604741cb3 (Aug 11 2017 - 15:47:09 -0500), Build:
> jenkins-github_Bootloader-Builder-592
>
> CPU : DRA752-GP ES2.0
> Model: TI AM5728 BeagleBoard-X15
> Board: AM572x EVM REV A.3A
> DRAM: 2 GiB
> MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
>
> ** Unable to use mmc 0:1 for loading the env **
> Using default environment
>
> setup_board_eeprom_env: am57xx_evm_reva3
> SCSI: SATA link 0 timeout.
> AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
> flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst
> scanning bus for devices...
> Found 0 device(s).
> Net: <ethaddr> not set. Validating first E-fuse MAC
> cpsw
> Press SPACE to abort autoboot in 2 seconds
> usb_boot is currently disabled
> scsi_boot is currently disabled
> switch to partitions #0, OK
> mmc0 is current device
> Scanning mmc device 0
> Checking for: /uEnv.txt ...
> Checking for: /boot/uEnv.txt ...
> 446 bytes read in 49 ms (8.8 KiB/s)
> Loaded environment from /boot/uEnv.txt
> Checking if uname_r is set in /boot/uEnv.txt ...
> debug: [uname_r=4.4.80-ti-r116] ...
> loading /boot/vmlinuz-4.4.80-ti-r116 ...
>
> 5487379 bytes read in 283 ms (18.5 MiB/s)
> debug: [console=ttyO2,115200n8 root=/dev/mmcblk0p1 ro rootfstype=ext4
> rootwait coherent_pool=1M net.ifnames=0 quiet] ...
> debug: [bootz 0x82000000 0x88080000:53bb13 0x88000000] ...
> ## Flattened Device Tree blob at 88000000
> Booting using the fdt blob at 0x88000000
> Loading Ramdisk to 8fac4000, end 8ffffb13 ... OK
> Loading Device Tree to 8fa9c000, end 8fac3782 ... OK
>
> Starting kernel ...
>
> [ 0.063779] /cpus/cpu@0 missing clock-frequency property
> [ 0.063800] /cpus/cpu@1 missing clock-frequency property
> [ 2.194996] dra7-pcie 51000000.pcie_rc: link is not up
> [ 2.540811] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode
> [ 2.547225] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode
> [ 2.639312] omap_voltage_late_init: Voltage driver support not added
> [ 3.537309] remoteproc0: failed to load am57xx-pru1_0-fw
> [ 3.542894] remoteproc0: request_firmware failed: -2
> [ 3.547988] pru-rproc 4b234000.pru0: rproc_boot failed
> [ 3.555830] remoteproc0: failed to load am57xx-pru1_1-fw
> [ 3.562347] remoteproc0: request_firmware failed: -2
> [ 3.567442] pru-rproc 4b238000.pru1: rproc_boot failed
> [ 3.581573] remoteproc0: failed to load am57xx-pru2_0-fw
> [ 3.588946] remoteproc0: request_firmware failed: -2
> [ 3.594048] pru-rproc 4b2b4000.pru0: rproc_boot failed
> [ 3.603674] remoteproc0: failed to load am57xx-pru2_1-fw
> [ 3.610193] remoteproc0: request_firmware failed: -2
> [ 3.615285] pru-rproc 4b2b8000.pru1: rproc_boot failed
> [ 5.899545] remoteproc0: failed to load dra7-ipu1-fw.xem4
> [ 5.923242] remoteproc2: failed to load dra7-dsp1-fw.xe66
> [ 5.932697] remoteproc3: failed to load dra7-dsp2-fw.xe66
> [ 6.517022] pixcir_ts 4-005c: pixcir_set_power_mode: can't read reg
> 0x33 : -121
> [ 6.517027] pixcir_ts 4-005c: Failed to set IDLE mode
>
> Debian GNU/Linux 9 arm ttyS2
>
> rcn-ee.net console Debian Image 2017-08-11
>
> Support/FAQ: http://elinux.org/BeagleBoardDebian
>
> default username:password is [debian:temppwd]
>
>
> On Monday, August 14, 2017 at 9:17:48 AM UTC-5, Jeff Andich wrote:
>>
>> Hi Robert,
>>
>> So far, so good. It boots and gives the "arm" prompt. Will collect some
>> cursory logs and post them back up here..
>>
>> Thanks and regards!
>>
>> Jeff
>>
>>
>> On Saturday, August 12, 2017 at 10:05:04 AM UTC-5, RobertCNelson wrote:
>>>
>>> Jeff, give this image a quick test:
>>>
>>>
>>> https://rcn-ee.net/rootfs/2017-08-11/microsd/bbx15-debian-9.1-console-armhf-2017-08-11-2gb.img.xz
>>>
>>>
>>> Regards,
>>>
>>> --
>>> Robert Nelson
>>> https://rcn-ee.com/
>>>
>>
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web visit
https://groups.google.com/d/msgid/beagleboard/38e7e05e-29cf-43a7-a94e-222317fe22e7%40googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
arm login: debian
Password:
Linux arm 4.4.80-ti-r116 #1 SMP Wed Aug 9 15:33:47 UTC 2017 armv7l
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
debian@arm:~$ dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.80-ti-r116 (root@b8-am57xx-beagle-x15-2gb)
(gcc version 6.3.0 20170516 (Debian 6.3.0-18) ) #1 SMP Wed Aug 9 15:33:47 UTC
2017
[ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine model: TI AM572x EVM Rev A3
[ 0.000000] Reserved memory: created CMA memory pool at 0x95800000, size 56
MiB
[ 0.000000] Reserved memory: initialized node ipu2_cma@95800000, compatible
id shared-dma-pool
[ 0.000000] Reserved memory: created CMA memory pool at 0x99000000, size 64
MiB
[ 0.000000] Reserved memory: initialized node dsp1_cma@99000000, compatible
id shared-dma-pool
[ 0.000000] Reserved memory: created CMA memory pool at 0x9d000000, size 32
MiB
[ 0.000000] Reserved memory: initialized node ipu1_cma@9d000000, compatible
id shared-dma-pool
[ 0.000000] Reserved memory: created CMA memory pool at 0x9f000000, size 8
MiB
[ 0.000000] Reserved memory: initialized node dsp2_cma@9f000000, compatible
id shared-dma-pool
[ 0.000000] cma: Reserved 48 MiB at 0xfc800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] OMAP4: Map 0xffd00000 to fe600000 for dram barrier
[ 0.000000] On node 0 totalpages: 474623
[ 0.000000] free_area_init_node: node 0, pgdat c106cfc0, node_mem_map
eeda8000
[ 0.000000] Normal zone: 1728 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 147456 pages, LIFO batch:31
[ 0.000000] HighMem zone: 327167 pages, LIFO batch:31
[ 0.000000] DRA752 ES2.0
[ 0.000000] PERCPU: Embedded 13 pages/cpu @eed23000 s24268 r8192 d20788
u53248
[ 0.000000] pcpu-alloc: s24268 r8192 d20788 u53248 alloc=13*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 472895
[ 0.000000] Kernel command line: console=ttyO2,115200n8 root=/dev/mmcblk0p1
ro rootfstype=ext4 rootwait coherent_pool=1M net.ifnames=0 quiet
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1643860K/1898492K available (11413K kernel code, 927K
rwdata, 3816K rodata, 736K init, 841K bss, 41640K reserved, 212992K
cma-reserved, 1259516K highmem)
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc0ee79f8 (15231 kB)
.init : 0xc0ee8000 - 0xc0fa0000 ( 736 kB)
.data : 0xc0fa0000 - 0xc1087c30 ( 928 kB)
.bss : 0xc108a000 - 0xc115c710 ( 842 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ti_dt_clocks_register: failed to lookup clock node
gmac_gmii_ref_clk_div
[ 0.000000] OMAP clockevent source: timer1 at 32786 Hz
[ 0.000000] Architected cp15 timer(s) running at 6.14MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff
max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns
[ 0.000004] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every
4398046511023ns
[ 0.000016] Switching to timer-based delay loop, resolution 162ns
[ 0.000538] clocksource: 32k_counter: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 58327039986419 ns
[ 0.000546] OMAP clocksource: 32k_counter at 32768 Hz
[ 0.001304] Console: colour dummy device 80x30
[ 0.001320] WARNING: Your 'console=ttyO2' has been replaced by 'ttyS2'
[ 0.001327] This ensures that you still see kernel messages. Please
[ 0.001333] update your kernel commandline.
[ 0.001347] Calibrating delay loop (skipped), value calculated using timer
frequency.. 12.29 BogoMIPS (lpj=24590)
[ 0.001360] pid_max: default: 32768 minimum: 301
[ 0.001453] Security Framework initialized
[ 0.001464] Yama: becoming mindful.
[ 0.001483] AppArmor: AppArmor disabled by boot time parameter
[ 0.001613] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001624] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.002243] Initializing cgroup subsys io
[ 0.002262] Initializing cgroup subsys memory
[ 0.002289] Initializing cgroup subsys devices
[ 0.002302] Initializing cgroup subsys freezer
[ 0.002314] Initializing cgroup subsys net_cls
[ 0.002324] Initializing cgroup subsys perf_event
[ 0.002337] Initializing cgroup subsys net_prio
[ 0.002353] Initializing cgroup subsys pids
[ 0.002389] CPU: Testing write buffer coherency: ok
[ 0.002423] ftrace: allocating 34880 entries in 103 pages
[ 0.063781] /cpus/cpu@0 missing clock-frequency property
[ 0.063801] /cpus/cpu@1 missing clock-frequency property
[ 0.063811] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.063863] Setting up static identity map for 0x80008280 - 0x800082e0
[ 0.067368] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.067459] Brought up 2 CPUs
[ 0.067472] SMP: Total of 2 processors activated (24.59 BogoMIPS).
[ 0.067479] CPU: All CPU(s) started in HYP mode.
[ 0.067484] CPU: Virtualization extensions available.
[ 0.068626] devtmpfs: initialized
[ 0.104724] VFP support v0.3: implementor 41 architecture 4 part 30 variant
f rev 0
[ 0.105701] omap_hwmod: l3_main_2 using broken dt data from ocp
[ 0.217142] omap_hwmod: dcan1: _wait_target_disable failed
[ 0.316451] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 7645041785100000 ns
[ 0.316472] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.320832] xor: measuring software checksum speed
[ 0.360265] arm4regs : 1987.000 MB/sec
[ 0.400338] 8regs : 1615.000 MB/sec
[ 0.440411] 32regs : 1500.000 MB/sec
[ 0.480476] neon : 2944.000 MB/sec
[ 0.480483] xor: using function: neon (2944.000 MB/sec)
[ 0.480506] pinctrl core: initialized pinctrl subsystem
[ 0.481468] NET: Registered protocol family 16
[ 0.483730] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.492551] cpuidle: using governor ladder
[ 0.504591] cpuidle: using governor menu
[ 0.513268] OMAP GPIO hardware version 0.1
[ 0.519453] irq: no irq domain found for
/ocp/l4@4a000000/scm@2000/pinmux@1400 !
[ 0.543921] No ATAGs?
[ 0.543953] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint
registers.
[ 0.543962] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.544490] omap4_sram_init:Unable to allocate sram needed to handle errata
I688
[ 0.544499] omap4_sram_init:Unable to get sram pool needed to handle errata
I688
[ 0.545023] OMAP DMA hardware revision 0.0
[ 0.633162] raid6: int32x1 gen() 226 MB/s
[ 0.701219] raid6: int32x1 xor() 250 MB/s
[ 0.769439] raid6: int32x2 gen() 329 MB/s
[ 0.837529] raid6: int32x2 xor() 333 MB/s
[ 0.905678] raid6: int32x4 gen() 370 MB/s
[ 0.973811] raid6: int32x4 xor() 355 MB/s
[ 1.042072] raid6: int32x8 gen() 423 MB/s
[ 1.110135] raid6: int32x8 xor() 328 MB/s
[ 1.178318] raid6: neonx1 gen() 890 MB/s
[ 1.246471] raid6: neonx1 xor() 800 MB/s
[ 1.314657] raid6: neonx2 gen() 1324 MB/s
[ 1.382780] raid6: neonx2 xor() 1245 MB/s
[ 1.450946] raid6: neonx4 gen() 1742 MB/s
[ 1.519119] raid6: neonx4 xor() 1285 MB/s
[ 1.587277] raid6: neonx8 gen() 1650 MB/s
[ 1.655438] raid6: neonx8 xor() 1230 MB/s
[ 1.655444] raid6: using algorithm neonx4 gen() 1742 MB/s
[ 1.655450] raid6: .... xor() 1285 MB/s, rmw enabled
[ 1.655456] raid6: using intx1 recovery algorithm
[ 1.668336] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver
(LinkedList1/2/3 supported)
[ 1.669415] edma 43300000.edma: memcpy is disabled
[ 1.675266] edma 43300000.edma: TI EDMA DMA engine driver
[ 1.680736] omap-iommu 40d01000.mmu: 40d01000.mmu registered
[ 1.680847] omap-iommu 40d02000.mmu: 40d02000.mmu registered
[ 1.680949] omap-iommu 58882000.mmu: 58882000.mmu registered
[ 1.681049] omap-iommu 55082000.mmu: 55082000.mmu registered
[ 1.681243] omap-iommu 41501000.mmu: 41501000.mmu registered
[ 1.681352] omap-iommu 41502000.mmu: 41502000.mmu registered
[ 1.683129] vgaarb: loaded
[ 1.683532] SCSI subsystem initialized
[ 1.683697] libata version 3.00 loaded.
[ 1.683938] usbcore: registered new interface driver usbfs
[ 1.684025] usbcore: registered new interface driver hub
[ 1.684099] usbcore: registered new device driver usb
[ 1.685338] palmas 0-0058: Irq flag is 0x00000008
[ 1.702249] palmas 0-0058: Muxing GPIO 2f, PWM 0, LED 0
[ 1.743951] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[ 1.744472] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz
[ 1.745067] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz
[ 1.745275] media: Linux media interface: v0.10
[ 1.745328] Linux video capture interface: v2.00
[ 1.745410] pps_core: LinuxPPS API ver. 1 registered
[ 1.745417] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
Giometti <[email protected]>
[ 1.745447] PTP clock support registered
[ 1.746017] omap-mailbox 4883c000.mailbox: omap mailbox rev 0x400
[ 1.746294] omap-mailbox 4883e000.mailbox: omap mailbox rev 0x400
[ 1.746577] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400
[ 1.746858] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400
[ 1.747825] NetLabel: Initializing
[ 1.747833] NetLabel: domain hash size = 128
[ 1.747838] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.747885] NetLabel: unlabeled traffic allowed by default
[ 1.748106] clocksource: Switched to clocksource arch_sys_counter
[ 1.837773] NET: Registered protocol family 2
[ 1.838364] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 1.838428] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.838553] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.838602] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 1.838633] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 1.838810] NET: Registered protocol family 1
[ 1.839174] RPC: Registered named UNIX socket transport module.
[ 1.839183] RPC: Registered udp transport module.
[ 1.839189] RPC: Registered tcp transport module.
[ 1.839195] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.839213] PCI: CLS 0 bytes, default 64
[ 1.839665] Unpacking initramfs...
[ 2.136717] Freeing initrd memory: 5360K (cfac4000 - d0000000)
[ 2.137488] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7
counters available
[ 2.140526] audit: initializing netlink subsys (disabled)
[ 2.140566] audit: type=2000 audit(2.103:1): initialized
[ 2.148567] zbud: loaded
[ 2.148980] VFS: Disk quotas dquot_6.6.0
[ 2.149180] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.151125] NFS: Registering the id_resolver key type
[ 2.151162] Key type id_resolver registered
[ 2.151170] Key type id_legacy registered
[ 2.151191] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 2.151396] fuse init (API version 7.23)
[ 2.151842] SGI XFS with ACLs, security attributes, realtime, no debug
enabled
[ 2.157051] bounce: pool size: 64 pages
[ 2.157100] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
249)
[ 2.157207] io scheduler noop registered
[ 2.157219] io scheduler deadline registered
[ 2.157259] io scheduler cfq registered (default)
[ 2.162251] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128
[ 2.165678] PCI host bridge /ocp/axi@0/pcie_rc@51000000 ranges:
[ 2.165691] No bus range found for /ocp/axi@0/pcie_rc@51000000, using [bus
00-ff]
[ 2.165723] IO 0x20003000..0x20012fff -> 0x00000000
[ 2.165744] MEM 0x20013000..0x2fffffff -> 0x20013000
[ 2.197411] dra7-pcie 51000000.pcie_rc: link is not up
[ 2.197604] dra7-pcie 51000000.pcie_rc: PCI host bridge to bus 0000:00
[ 2.197617] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.197627] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 2.197637] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff]
[ 2.197671] pci 0000:00:00.0: [104c:8888] type 01 class 0x060400
[ 2.197715] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 2.197737] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 2.197807] pci 0000:00:00.0: supports D1
[ 2.197817] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 2.198059] PCI: bus0: Fast back to back transfers disabled
[ 2.198198] PCI: bus1: Fast back to back transfers enabled
[ 2.198270] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff]
[ 2.198284] pci 0000:00:00.0: BAR 1: assigned [mem 0x20020000-0x2002ffff]
[ 2.198296] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.198966] backlight supply power not found, using dummy regulator
[ 2.203268] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[ 2.205767] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 301, base_baud
= 3000000) is a 8250
[ 2.222147] console [ttyS2] enabled
[ 2.222749] 48422000.serial: ttyS0 at MMIO 0x48422000 (irq = 302, base_baud
= 3000000) is a 8250
[ 2.224251] [drm] Initialized drm 1.1.0 20060810
[ 2.226516] OMAP DSS rev 6.1
[ 2.227555] omapdss_dss 58000000.dss: bound 58001000.dispc (ops
dispc_component_ops)
[ 2.228185] omapdss_dss 58000000.dss: bound 58040000.encoder (ops
hdmi5_component_ops)
[ 2.230180] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write
[ 2.232228] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled
[ 2.232257] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1
impl platform mode
[ 2.232271] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only
pmp pio slum part ccc apst
[ 2.233205] scsi host0: ahci
[ 2.233501] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port
0x100 irq 348
[ 2.268131] davinci_mdio 48485000.mdio: davinci mdio revision 1.6
[ 2.268143] davinci_mdio 48485000.mdio: detected phy mask fffffff9
[ 2.277812] libphy: 48485000.mdio: probed
[ 2.277827] davinci_mdio 48485000.mdio: phy[1]: device 48485000.mdio:01,
driver Micrel KSZ9031 Gigabit PHY
[ 2.277837] davinci_mdio 48485000.mdio: phy[2]: device 48485000.mdio:02,
driver Micrel KSZ9031 Gigabit PHY
[ 2.278448] cpsw 48484000.ethernet: Detected MACID = 5c:f8:21:36:b9:f4
[ 2.278527] cpsw 48484000.ethernet: cpts: overflow check period 2000
[ 2.279167] cpsw 48484000.ethernet: cpsw: Detected MACID = 5c:f8:21:36:b9:f5
[ 2.482755] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.482779] ehci-pci: EHCI PCI platform driver
[ 2.482834] ehci-platform: EHCI generic platform driver
[ 2.483179] ehci-omap: OMAP-EHCI Host Controller driver
[ 2.483858] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 2.483884] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus
number 1
[ 2.484239] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f04c hci version
0x100 quirks 0x00210010
[ 2.484285] xhci-hcd xhci-hcd.1.auto: irq 440, io mem 0x48890000
[ 2.484472] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.484482] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.484491] usb usb1: Product: xHCI Host Controller
[ 2.484498] usb usb1: Manufacturer: Linux 4.4.80-ti-r116 xhci-hcd
[ 2.484506] usb usb1: SerialNumber: xhci-hcd.1.auto
[ 2.485116] hub 1-0:1.0: USB hub found
[ 2.485160] hub 1-0:1.0: 1 port detected
[ 2.485556] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 2.485579] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus
number 2
[ 2.485662] usb usb2: We don't know the algorithms for LPM for this host,
disabling LPM.
[ 2.485791] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.485801] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.485810] usb usb2: Product: xHCI Host Controller
[ 2.485817] usb usb2: Manufacturer: Linux 4.4.80-ti-r116 xhci-hcd
[ 2.485825] usb usb2: SerialNumber: xhci-hcd.1.auto
[ 2.486389] hub 2-0:1.0: USB hub found
[ 2.486426] hub 2-0:1.0: 1 port detected
[ 2.486944] usbcore: registered new interface driver usb-storage
[ 2.487902] mousedev: PS/2 mouse device common for all mice
[ 2.488340] palmas_pwrbutton 48070000.i2c:tps659038@58:tps659038_pwr_button:
h/w controlled shutdown duration=12 seconds
[ 2.490048] input: palmas_pwron as
/devices/platform/44000000.ocp/48070000.i2c/i2c-0/0-0058/48070000.i2c:tps659038@58:tps659038_pwr_button/input/input0
[ 2.491761] omap_rtc 48838000.rtc: rtc core: registered 48838000.rtc as rtc2
[ 2.492166] i2c /dev entries driver
[ 2.494375] gpio-fan gpio_fan: GPIO fan initialized
[ 2.497144] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 2.498311] omap_hsmmc 4809c000.mmc: Got CD GPIO
[ 2.498581] vdd_3v3: supplied by regen1
[ 2.540642] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode
[ 2.547046] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode
[ 2.556145] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.621267] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.621707] usbcore: registered new interface driver usbhid
[ 2.621714] usbhid: USB HID core driver
[ 2.625961] NET: Registered protocol family 10
[ 2.626947] mip6: Mobile IPv6
[ 2.626967] NET: Registered protocol family 17
[ 2.627050] Key type dns_resolver registered
[ 2.627062] mpls_gso: MPLS GSO support
[ 2.627214] omap_voltage_late_init: Voltage driver support not added
[ 2.634191] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
[ 2.634200] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
[ 2.634611] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm
[ 2.634621] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm
[ 2.636566] Power Management for TI OMAP4+ devices.
[ 2.636747] ThumbEE CPU extension supported.
[ 2.636764] Registering SWP/SWPB emulation handler
[ 2.637220] registered taskstats version 1
[ 2.637302] zswap: loaded using pool lzo/zbud
[ 2.639084] Btrfs loaded
[ 2.651367] Key type encrypted registered
[ 2.653050] dmm 4e000000.dmm: initialized all PAT entries
[ 2.653555] backlight supply power not found, using dummy regulator
[ 2.796580] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 2.855709] backlight supply power not found, using dummy regulator
[ 2.857095] input: gpio_keys as /devices/platform/gpio_keys/input/input1
[ 2.857178] hctosys: unable to open rtc device (rtc0)
[ 2.857189] of_cfs_init
[ 2.857238] of_cfs_init: OK
[ 2.864393] backlight supply power not found, using dummy regulator
[ 2.866509] PM: Hibernation image not present or could not be loaded.
[ 2.866525] aic_dvdd_fixed: disabling
[ 2.867254] Freeing unused kernel memory: 736K (c0ee8000 - c0fa0000)
[ 2.910056] random: systemd-udevd: uninitialized urandom read (16 bytes
read, 7 bits of entropy available)
[ 2.910363] random: systemd-udevd: uninitialized urandom read (16 bytes
read, 7 bits of entropy available)
[ 2.910417] random: systemd-udevd: uninitialized urandom read (16 bytes
read, 7 bits of entropy available)
[ 2.916666] random: udevadm: uninitialized urandom read (16 bytes read, 7
bits of entropy available)
[ 2.916792] random: udevadm: uninitialized urandom read (16 bytes read, 7
bits of entropy available)
[ 2.916861] random: udevadm: uninitialized urandom read (16 bytes read, 7
bits of entropy available)
[ 2.917103] random: udevadm: uninitialized urandom read (16 bytes read, 7
bits of entropy available)
[ 2.917433] random: udevadm: uninitialized urandom read (16 bytes read, 7
bits of entropy available)
[ 2.917709] random: udevadm: uninitialized urandom read (16 bytes read, 7
bits of entropy available)
[ 2.917976] random: udevadm: uninitialized urandom read (16 bytes read, 7
bits of entropy available)
[ 2.932607] usb 1-1: New USB device found, idVendor=0451, idProduct=8142
[ 2.932615] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=1
[ 2.932622] usb 1-1: SerialNumber: C80200611D05
[ 2.967310] hub 1-1:1.0: USB hub found
[ 2.968348] hub 1-1:1.0: 4 ports detected
[ 3.005499] backlight supply power not found, using dummy regulator
[ 3.037918] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 3.058130] usb 2-1: New USB device found, idVendor=0451, idProduct=8140
[ 3.058139] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.078818] hub 2-1:1.0: USB hub found
[ 3.079848] hub 2-1:1.0: 4 ports detected
[ 3.089671] backlight supply power not found, using dummy regulator
[ 3.216721] rtc-ds1307 2-006f: SET TIME!
[ 3.219010] rtc-ds1307 2-006f: rtc core: registered mcp7941x as rtc0
[ 3.224279] rtc-ds1307 2-006f: 64 bytes nvram
[ 3.224584] backlight supply power not found, using dummy regulator
[ 3.327383] palmas-rtc 48070000.i2c:tps659038@58:tps659038_rtc: rtc core:
registered 48070000.i2c:tps659 as rtc1
[ 3.329024] backlight supply power not found, using dummy regulator
[ 3.511253] ti-pruss 4b200000.pruss: creating PRU cores and other child
platform devices
[ 3.511974] irq: no irq domain found for /ocp/pruss@4b200000/intc@4b220000 !
[ 3.512399] irq: no irq domain found for /ocp/pruss@4b200000/intc@4b220000 !
[ 3.512832] backlight supply power not found, using dummy regulator
[ 3.513273] ti-pruss 4b280000.pruss: creating PRU cores and other child
platform devices
[ 3.513869] irq: no irq domain found for /ocp/pruss@4b280000/intc@4b2a0000 !
[ 3.514178] irq: no irq domain found for /ocp/pruss@4b280000/intc@4b2a0000 !
[ 3.514559] backlight supply power not found, using dummy regulator
[ 3.516233] backlight supply power not found, using dummy regulator
[ 3.520800] backlight supply power not found, using dummy regulator
[ 3.523125] remoteproc0: 4b234000.pru0 is available
[ 3.523132] remoteproc0: Note: remoteproc is still under development and
considered experimental.
[ 3.523137] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and
backward compatibility isn't yet guaranteed.
[ 3.523230] remoteproc0: Direct firmware load for am57xx-pru1_0-fw failed
with error -2
[ 3.523239] remoteproc0: failed to load am57xx-pru1_0-fw
[ 3.528792] pru-rproc 4b234000.pru0: booting the PRU core manually
[ 3.528798] remoteproc0: powering up 4b234000.pru0
[ 3.528837] remoteproc0: Direct firmware load for am57xx-pru1_0-fw failed
with error -2
[ 3.528843] remoteproc0: request_firmware failed: -2
[ 3.533926] pru-rproc 4b234000.pru0: rproc_boot failed
[ 3.560969] remoteproc0: releasing 4b234000.pru0
[ 3.561051] pru-rproc: probe of 4b234000.pru0 failed with error -2
[ 3.561227] remoteproc0: 4b238000.pru1 is available
[ 3.561233] remoteproc0: Note: remoteproc is still under development and
considered experimental.
[ 3.561239] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and
backward compatibility isn't yet guaranteed.
[ 3.561333] remoteproc0: Direct firmware load for am57xx-pru1_1-fw failed
with error -2
[ 3.561341] remoteproc0: failed to load am57xx-pru1_1-fw
[ 3.566797] pru-rproc 4b238000.pru1: booting the PRU core manually
[ 3.566803] remoteproc0: powering up 4b238000.pru1
[ 3.566843] remoteproc0: Direct firmware load for am57xx-pru1_1-fw failed
with error -2
[ 3.566850] remoteproc0: request_firmware failed: -2
[ 3.571935] pru-rproc 4b238000.pru1: rproc_boot failed
[ 3.600589] remoteproc0: releasing 4b238000.pru1
[ 3.600680] pru-rproc: probe of 4b238000.pru1 failed with error -2
[ 3.600883] remoteproc0: 4b2b4000.pru0 is available
[ 3.600890] remoteproc0: Note: remoteproc is still under development and
considered experimental.
[ 3.600895] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and
backward compatibility isn't yet guaranteed.
[ 3.600992] remoteproc0: Direct firmware load for am57xx-pru2_0-fw failed
with error -2
[ 3.601001] remoteproc0: failed to load am57xx-pru2_0-fw
[ 3.606491] pru-rproc 4b2b4000.pru0: booting the PRU core manually
[ 3.606499] remoteproc0: powering up 4b2b4000.pru0
[ 3.606552] remoteproc0: Direct firmware load for am57xx-pru2_0-fw failed
with error -2
[ 3.606559] remoteproc0: request_firmware failed: -2
[ 3.611658] pru-rproc 4b2b4000.pru0: rproc_boot failed
[ 3.619128] remoteproc0: releasing 4b2b4000.pru0
[ 3.619233] pru-rproc: probe of 4b2b4000.pru0 failed with error -2
[ 3.619425] remoteproc0: 4b2b8000.pru1 is available
[ 3.619432] remoteproc0: Note: remoteproc is still under development and
considered experimental.
[ 3.619436] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and
backward compatibility isn't yet guaranteed.
[ 3.619565] remoteproc0: Direct firmware load for am57xx-pru2_1-fw failed
with error -2
[ 3.619573] remoteproc0: failed to load am57xx-pru2_1-fw
[ 3.625069] pru-rproc 4b2b8000.pru1: booting the PRU core manually
[ 3.625075] remoteproc0: powering up 4b2b8000.pru1
[ 3.625122] remoteproc0: Direct firmware load for am57xx-pru2_1-fw failed
with error -2
[ 3.625129] remoteproc0: request_firmware failed: -2
[ 3.630255] pru-rproc 4b2b8000.pru1: rproc_boot failed
[ 3.642092] remoteproc0: releasing 4b2b8000.pru1
[ 3.642169] pru-rproc: probe of 4b2b8000.pru1 failed with error -2
[ 3.663211] mmc0: host does not support reading read-only switch, assuming
write-enable
[ 3.665137] mmc0: new high speed SDHC card at address 0007
[ 3.665597] mmcblk0: mmc0:0007 SD32G 29.0 GiB
[ 3.666560] mmcblk0: p1
[ 3.667244] backlight supply power not found, using dummy regulator
[ 3.722802] mmc1: MAN_BKOPS_EN bit is not set
[ 3.731587] mmc1: new DDR MMC card at address 0001
[ 3.732092] mmcblk1: mmc1:0001 S10004 3.56 GiB
[ 3.732386] mmcblk1boot0: mmc1:0001 S10004 partition 1 4.00 MiB
[ 3.732660] mmcblk1boot1: mmc1:0001 S10004 partition 2 4.00 MiB
[ 3.733391] mmcblk1: p1 p2 p3
[ 3.736816] backlight supply power not found, using dummy regulator
[ 3.957324] EXT4-fs (mmcblk0p1): INFO: recovery required on readonly
filesystem
[ 3.957333] EXT4-fs (mmcblk0p1): write access will be enabled during recovery
[ 4.341920] EXT4-fs (mmcblk0p1): recovery complete
[ 4.500371] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode.
Opts: (null)
[ 4.915677] systemd[1]: System time before build time, advancing clock.
[ 4.987812] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.015457] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT
+SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS
+ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 5.015753] systemd[1]: Detected architecture arm.
[ 5.016528] systemd[1]: Set hostname to <arm>.
[ 5.340801] systemd[1]: Reached target Remote File Systems.
[ 5.341107] systemd[1]: Listening on Journal Socket.
[ 5.341220] systemd[1]: Listening on Syslog Socket.
[ 5.341324] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 5.341853] systemd[1]: Created slice User and Session Slice.
[ 5.342257] systemd[1]: Created slice System Slice.
[ 5.360423] systemd[1]: Starting Load Kernel Modules...
[ 5.360958] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 5.362978] systemd[1]: Starting File System Check on Root Device...
[ 5.376659] systemd[1]: Mounting POSIX Message Queue File System...
[ 5.377385] systemd[1]: Listening on Journal Audit Socket.
[ 5.377537] systemd[1]: Reached target Swap.
[ 5.377600] systemd[1]: Reached target Slices.
[ 5.379041] systemd[1]: Started Forward Password Requests to Wall Directory
Watch.
[ 5.379249] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 5.379470] systemd[1]: Started Dispatch Password Requests to Console
Directory Watch.
[ 5.379619] systemd[1]: Listening on Journal Socket (/dev/log).
[ 5.384008] systemd[1]: Starting Journal Service...
[ 5.384746] systemd[1]: Created slice system-getty.slice.
[ 5.385555] systemd[1]: Set up automount Arbitrary Executable File Formats
File System Automount Point.
[ 5.385817] systemd[1]: Listening on udev Control Socket.
[ 5.436504] systemd[1]: Mounting /sys/kernel/debug...
[ 5.436712] systemd[1]: Listening on udev Kernel Socket.
[ 5.436865] systemd[1]: Reached target Encrypted Volumes.
[ 5.438954] systemd[1]: Starting Create list of required static device nodes
for the current kernel...
[ 5.455075] systemd[1]: Started Load Kernel Modules.
[ 5.477226] systemd[1]: Mounted POSIX Message Queue File System.
[ 5.477610] systemd[1]: Mounted /sys/kernel/debug.
[ 5.489074] systemd[1]: Started File System Check Daemon to report status.
[ 5.491299] systemd[1]: Mounting FUSE Control File System...
[ 5.524311] systemd[1]: Starting Apply Kernel Variables...
[ 5.526632] systemd[1]: Mounting Configuration File System...
[ 5.544675] systemd[1]: Started File System Check on Root Device.
[ 5.545968] systemd[1]: Started Create list of required static device nodes
for the current kernel.
[ 5.546507] systemd[1]: Mounted FUSE Control File System.
[ 5.557625] systemd[1]: Started Journal Service.
[ 5.604315] EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro
[ 5.647367] systemd-journald[254]: Received request to flush runtime journal
from PID 1
[ 6.474366] omap-rproc 58820000.ipu: assigned reserved memory node
ipu1_cma@9d000000
[ 6.474429] remoteproc0: 58820000.ipu is available
[ 6.474435] remoteproc0: Note: remoteproc is still under development and
considered experimental.
[ 6.474441] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and
backward compatibility isn't yet guaranteed.
[ 6.475501] backlight supply power not found, using dummy regulator
[ 6.476033] omap-rproc 55020000.ipu: assigned reserved memory node
ipu2_cma@95800000
[ 6.476085] remoteproc1: 55020000.ipu is available
[ 6.476091] remoteproc1: Note: remoteproc is still under development and
considered experimental.
[ 6.476142] remoteproc1: THE BINARY FORMAT IS NOT YET FINALIZED, and
backward compatibility isn't yet guaranteed.
[ 6.476479] backlight supply power not found, using dummy regulator
[ 6.476959] omap-rproc 40800000.dsp: assigned reserved memory node
dsp1_cma@99000000
[ 6.477003] remoteproc2: 40800000.dsp is available
[ 6.477009] remoteproc2: Note: remoteproc is still under development and
considered experimental.
[ 6.477016] remoteproc2: THE BINARY FORMAT IS NOT YET FINALIZED, and
backward compatibility isn't yet guaranteed.
[ 6.477266] backlight supply power not found, using dummy regulator
[ 6.477800] omap-rproc 41000000.dsp: assigned reserved memory node
dsp2_cma@9f000000
[ 6.477844] remoteproc3: 41000000.dsp is available
[ 6.477849] remoteproc3: Note: remoteproc is still under development and
considered experimental.
[ 6.477853] remoteproc3: THE BINARY FORMAT IS NOT YET FINALIZED, and
backward compatibility isn't yet guaranteed.
[ 6.478089] backlight supply power not found, using dummy regulator
[ 6.494577] remoteproc0: Direct firmware load for dra7-ipu1-fw.xem4 failed
with error -2
[ 6.494592] remoteproc0: failed to load dra7-ipu1-fw.xem4
[ 6.512022] remoteproc2: Direct firmware load for dra7-dsp1-fw.xe66 failed
with error -2
[ 6.512037] remoteproc2: failed to load dra7-dsp1-fw.xe66
[ 6.517776] remoteproc3: Direct firmware load for dra7-dsp2-fw.xe66 failed
with error -2
[ 6.517786] remoteproc3: failed to load dra7-dsp2-fw.xe66
[ 6.710422] tmp102 0-0048: initialized
[ 6.710777] backlight supply power not found, using dummy regulator
[ 6.850467] backlight supply power not found, using dummy regulator
[ 6.860688] remoteproc1: registered virtio0 (type 7)
[ 6.866227] aic_dvdd_fixed: supplied by vdd_3v3
[ 6.866630] backlight supply power not found, using dummy regulator
[ 6.913424] omap_rng 48090000.rng: OMAP Random Number Generator ver. 20
[ 6.924011] backlight supply power not found, using dummy regulator
[ 6.958960] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2
[ 7.037165] backlight supply power not found, using dummy regulator
[ 7.039862] pixcir_ts 4-005c: pixcir_set_power_mode: can't read reg 0x33 :
-121
[ 7.047265] pixcir_ts 4-005c: Failed to set IDLE mode
[ 7.061127] Bluetooth: Core ver 2.21
[ 7.061191] NET: Registered protocol family 31
[ 7.061200] Bluetooth: HCI device and connection manager initialized
[ 7.061215] Bluetooth: HCI socket layer initialized
[ 7.061227] Bluetooth: L2CAP socket layer initialized
[ 7.061255] Bluetooth: SCO socket layer initialized
[ 7.196587] pixcir_ts: probe of 4-005c failed with error -121
[ 7.271181] backlight supply power not found, using dummy regulator
[ 7.289570] backlight supply power not found, using dummy regulator
[ 7.299023] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 7.299033] [drm] No driver support for vblank timestamp query.
[ 7.302568] [drm] Enabling DMM ywrap scrolling
[ 7.328720] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 7.351502] Console: switching to colour frame buffer device 100x30
[ 7.353752] omapdrm omapdrm.0: fb0: omapdrm frame buffer device
[ 7.376259] [drm] Initialized omapdrm 1.0.0 20110917 on minor 0
[ 7.507418] net eth0: initializing cpsw version 1.15 (0)
[ 7.507435] net eth0: initialized cpsw ale version 1.4
[ 7.507444] net eth0: ALE Table size 1024
[ 7.585901] net eth0: phy found : id is : 0x221622
[ 7.597415] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7.599253] net eth1: initializing cpsw version 1.15 (0)
[ 7.690420] net eth1: phy found : id is : 0x221622
[ 7.701021] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 7.703637] vpe 489d0000.vpe: loading firmware vpdma-1b8.bin
[ 7.724329] vpe 489d0000.vpe: Device registered as /dev/video0
[ 7.900764] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3
[ 7.914414] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3
[ 7.919043] omap-aes 4b700000.aes: OMAP AES hw accel rev: 3.3
[ 7.962670] etnaviv gpu-subsystem: bound 59000000.bb2d (ops gpu_ops
[etnaviv])
[ 7.962685] etnaviv-gpu 59000000.bb2d: model: GC320, revision: 5301
[ 8.127055] asoc-simple-card sound@0: tlv320aic3x-hifi <-> 48468000.mcasp
mapping ok
[ 8.166417] remoteproc1: powering up 55020000.ipu
[ 8.210042] remoteproc1: Booting fw image dra7-ipu2-fw.xem4, size 3743100
[ 8.210119] omap-iommu 55082000.mmu: 55082000.mmu: version 2.1
[ 8.274254] remoteproc1: remote processor 55020000.ipu is now up
[ 8.275267] virtio_rpmsg_bus virtio0: rpmsg host is online
[ 8.282738] virtio_rpmsg_bus virtio0: creating channel rpmsg-rpc addr 0x65
[ 8.283633] virtio_rpmsg_bus virtio0: creating channel rpmsg-rpc addr 0x66
[ 8.297359] rpmsg_rpc rpmsg0: probing service dce-callback with src 1024 dst
101
[ 8.298146] rpmsg_rpc rpmsg1: probing service rpmsg-dce with src 1025 dst 102
[ 8.298525] rpmsg_rpc rpmsg0: published functions = 4
[ 8.303684] rpmsg_rpc rpmsg1: published functions = 9
[ 10.600754] cpsw 48484000.ethernet eth0: Link is Up - 100Mbps/Full - flow
control rx/tx
[ 10.600802] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 10.649456] 8021q: 802.1Q VLAN Support v1.8
[ 10.649515] 8021q: adding VLAN 0 to HW filter on device eth0
[ 10.649575] 8021q: adding VLAN 0 to HW filter on device eth1
