I guess if it didn't have to be perfectly round, you could drill a hole in the thing and cut it out with air nibblers if you have access to those.
Bill Stephan Kansas City, MO (816)803-2469 William Stephan -----Original Message----- .From: "Boyce, Ray"<[EMAIL PROTECTED]> .Sent: 6/27/07 11:00:48 PM .To: "[email protected]"<[email protected]> .Subject: RE: [BlindHandyMan] Cutting Circles in Sheet Metal . .Hi Rob . .No I do not thing the nail would do the trick, do you know anyone with a .Oxy cutting set. .I have cut up plenty of drums and the steel is thick to withstand the .oil being stored inside and the rough handling these drums are subjected .to. .For there is a scriber you clamp to the oxy set just put that in the .centre and move the oxy cutter around to cut out the circle. .If you are going to use an oxy set be careful there is no residue inside .which is inflammable. .We used to cut the bottom and tops of these drums up and weld them .together to form a long vacuumed tube to suck the coal dust from the .coal face when they were extracting coal. .We had a vacuumed pump at one end and it worked great. .If you could find a can or the bottom of a container slightly smaller .than the required diameter and screw it onto the lid then you could use .and angle grinder held against the can as a guide. .Or mark out the circle centre punch it and split it into 4 using an .angle grinder and cut around using tin snips feeling the centre punch .marks as a guide once you have a quarter section removed then it becomes .easier. .Do you know a plumber close by who I am sure would have hole saws on .hand that you could borrow. .Let us know how or what method you used. . .ray . .________________________________ . .From: [email protected] .[mailto:[EMAIL PROTECTED] On Behalf Of Rob Monitor .Sent: Thursday, 28 June 2007 13:26 .To: [email protected] .Subject: Re: [BlindHandyMan] Cutting Circles in Sheet Metal . . . .This is Rob again, Ray what I'm cutting the hole in is a 55 gallon oil .drum top. Do you think this nail cutting thing would work for that?? .Also I do have a router and could there be any way I could use that?? .THANKS ROB .----- Original Message ----- .From: Boyce, Ray .To: [email protected] .<mailto:blindhandyman%40Yahoogroups.Com> .Sent: Wednesday, June 27, 2007 9:34 PM .Subject: [BlindHandyMan] Cutting Circles in Sheet Metal . .Hi Rob . .The cheapest form of a circle cutting jig is just a piece of wood with a .hole drilled as the centre point with a screw and nut to lock it in .position and a nail driven through at the desired diameter with the .point of the nail used as a cutting edge. .Just revolve it around until you cut through the metal if it becomes .dull use another sharp nail. .You can get metal cutting blades for a Jig Saw and circle cutting tin .snips also nibblers if you have a compressor. .Also there are things called trammels which have points both ends which .boiler makers use for marking out circles. .But for a one off cut try the wood and nail trick. .What you did not say is how thick this sheet metal is you are trying to .cut. .If it is really thin like sheet copper you could use scissors. .HTH . .Ray . .********************************************************************** .This message and its attachments may contain legally .privileged or confidential information. If you are not the .intended recipient, you must not disclose or use the .information contained in it. If you have received this e-mail .in error, please notify the sender immediately by return .e-mail and delete the e-mail. . .Any content of this message and its attachments which .does not relate to the official business of Eraring Energy .must be taken not to have been sent or endorsed by .Eraring Energy. No warranty is made that the e-mail or .attachment(s) are free from computer virus or other defect. .********************************************************************** . .[Non-text portions of this message have been removed] . .[Non-text portions of this message have been removed] . . . . . . .[Non-text portions of this message have been removed] . .
