I missed that little detail. But like I said you have to start somewhere. ----- Original Message ----- From: Larry Stansifer To: [email protected] Sent: Tuesday, January 08, 2008 6:39 PM Subject: RE: [BlindHandyMan] Dodge Intrepid
Customer advised that the oil light had been on for about 4000 miles. I've never seen an oil pump take that long to give it up without some pretty ugly noises coming from within. I could maybe go with a stuck pressure relief valve that will allow the motor to circulate oil but not with enough pressure to blow the light out. -----Original Message----- From: [email protected] [mailto:[EMAIL PROTECTED] On Behalf Of Bob Kennedy Sent: Tuesday, January 08, 2008 4:29 PM To: [email protected] Subject: Re: [BlindHandyMan] Dodge Intrepid That's the bad news yes... A clogged pick up screen, warn cam bearings can all play a part. But you have to start somewhere and without an actual oil pressure gauge it will be a guessing game. ----- Original Message ----- From: robert moore To: [email protected] Sent: Tuesday, January 08, 2008 12:35 PM Subject: RE: [BlindHandyMan] Dodge Intrepid Correct me if I am wrong but wouldn't a failed or failing oil pump be a prime suspect in this case? -----Original Message----- From: [email protected] [mailto:[EMAIL PROTECTED] Behalf Of Bob Kennedy Sent: Monday, January 07, 2008 8:30 PM To: [email protected] Subject: Re: [BlindHandyMan] Dodge Intrepid I worked for Dodge but I don't remember if that is a spade or ring connector. You may have to work at it when it is a bit warm to break it loose. Unfortunately a sending unit may not be the fix though. That is the easiest to change out though. Beyond that there are a few items that cost a little bit to replace if the engine hasn't warn out as a result. Keep working at the sending unit for a little while but listen for any new noises in the engine. ----- Original Message ----- From: NLG To: [email protected] <mailto:blindhandyman%40yahoogroups.com> Sent: Monday, January 07, 2008 3:25 PM Subject: Re: [BlindHandyMan] Dodge Intrepid I will have to keep trying. I tried pulling it off but it won't release. I tried feeling to see if there was a place to push on to get it to release but like I said, it is in very tight quarters. There isn't any oil leaking from the sending unit so it is clean. I am replacing it because the oil light is illuminated and won't go out. The engine oil level inddicates full on the dip stick. Thanks. ----- Original Message ----- From: Larry Stansifer To: [email protected] <mailto:blindhandyman%40yahoogroups.com> Sent: Monday, January 07, 2008 15:16 Subject: RE: [BlindHandyMan] Dodge Intrepid Should just be a male/female push on connector. If it has been leaking for a while the wire and/or the connector will probably break off in your hand, but that is an easy fix. -----Original Message----- From: [email protected] <mailto:blindhandyman%40yahoogroups.com> [mailto: [email protected] <mailto:blindhandyman%40yahoogroups.com> ] On Behalf Of NLG Sent: Monday, January 07, 2008 12:34 PM To: [email protected] <mailto:blindhandyman%40yahoogroups.com> Subject: [BlindHandyMan] Dodge Intrepid Any Dodge boys here? What kind of release is on the wire that attaches to an oil sending unit on a 2000 Dodge Intrepid? with the 2.2 engine? It is Hard to get at and when I finally get my fingers on it, I have very little room to maneuver. Thanks. To listen to the show archives go to link http://acbradio.org/handyman.html <http://acbradio.org/handyman.html> or ftp://ftp.acbradio.org/acbradio-archives/handyman/ <ftp://ftp.acbradio.org/acbradio-archives/handyman/> The Pod Cast address for the Blind Handy Man Show is. http://www.acbradio.org/news/xml/podcast.php?pgm=saturday <http://www.acbradio.org/news/xml/podcast.php?pgm=saturday> Visit The Blind Handy Man Files Page To Review Contributions From Various List Members At The Following address: http://www.jaws-users.com/JAWS/handyman/ <http://www.jaws-users.com/JAWS/handyman/> Visit the archives page at the following address http://www.mail-archive.com/[email protected]/ <http://www.mail-archive.com/[email protected]/> If you would like to join the JAWS Users List, then visit the following address for more information: http://www.jaws-users.com/ <http://www.jaws-users.com/> For a complete list of email commands pertaining to the Blind Handy Man list just send a blank message to: [EMAIL PROTECTED] <mailto:blindhandyman-help%40yahoogroups.com> Yahoo! Groups Links -- [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] To listen to the show archives go to link http://acbradio.org/handyman.html or ftp://ftp.acbradio.org/acbradio-archives/handyman/ The Pod Cast address for the Blind Handy Man Show is. http://www.acbradio.org/news/xml/podcast.php?pgm=saturday Visit The Blind Handy Man Files Page To Review Contributions From Various List Members At The Following address: http://www.jaws-users.com/JAWS/handyman/ Visit the archives page at the following address http://www.mail-archive.com/[email protected]/ If you would like to join the JAWS Users List, then visit the following address for more information: http://www.jaws-users.com/ For a complete list of email commands pertaining to the Blind Handy Man list just send a blank message to: [EMAIL PROTECTED] Yahoo! Groups Links -- BEGIN-ANTISPAM-VOTING-LINKS ------------------------------------------------------ Teach InfoWest Spam Trap if this mail (ID 149624160) is spam: Spam: https://spamtrap.infowest.com/canit/b.php?i=149624160&m=366b661058db&c=s Not spam: https://spamtrap.infowest.com/canit/b.php?i=149624160&m=366b661058db&c=n Forget vote: https://spamtrap.infowest.com/canit/b.php?i=149624160&m=366b661058db&c=f ------------------------------------------------------ END-ANTISPAM-VOTING-LINKS [Non-text portions of this message have been removed]
