Does the Telco Systems EdgeLink100 T1/E1 include an A/B side for redundant DC power? I couldn't discern that from the spec sheet.
We've been recommended (and installed) the Adtran series of products. Frank -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of OCOSA ListAcct Sent: Sunday, September 02, 2007 9:42 AM To: Ted Mittelstaedt Cc: [email protected] Subject: Re: [c-nsp] Multiple T1 IMA / Channelized DS3 Thanks seems to be cheaper than the Adtran MX2800 setup.... Otis Ted Mittelstaedt wrote: > Hi, > > Telco Systems sells boxes that will break out a channelized DS3 into > T1s. You can get them off Ebay for about $500-$800. That is how we > handle our channelized DS3s. We break them out with the Telco systems > boxes then run the T1's through a DSU bank then into PA-8T serial cards > with octopus cable. The Telco systems boxes, DSU bank and 8 port serial > cars grand total is far cheaper than getting channelized DS3 cards for > the 7206 and you also could use this to break a DS3 down into some > IMA channels that run into your PA-A3-8T1IMA card and others that run > into a standard T1 card. > > Ted > > >> -----Original Message----- >> From: [EMAIL PROTECTED] >> [mailto:[EMAIL PROTECTED] Behalf Of OCOSA ListAcct >> Sent: Tuesday, August 28, 2007 7:56 PM >> To: Joe Freeman >> Cc: [email protected] >> Subject: Re: [c-nsp] Multiple T1 IMA / Channelized DS3 >> >> >> Ok. I spoke with AT&T earlier they said that they have other customers >> taking some T1 IMAs over a channelized DS3 into the same router I was >> like how they said they would have a tech contact me I was ok. I thought >> maybe take the DS3 circuit into some sort of mux and split the signal >> from the IMA and send to a cross connect and then to the PA-A3-8T1IMA >> card....Can anyone shed some light here? Any help is appreciated! >> >> Otis >> >> Joe Freeman wrote: >> >>> PA-MC-T3 cards won't do IMA. >>> >>> That said... Does anyone have any suggestions for scaling NxDS0 >>> circuits muxed to ChDS3 in a 7206 chassis beyond 12 DS3's? >>> >>> Joe >>> >>> On 8/28/07, *OCOSA ListAcct* <[EMAIL PROTECTED] >>> <mailto:[EMAIL PROTECTED]>> wrote: >>> >>> Has anyone took a channelized DS3 circuit using a (PA-MC-T3) and >>> place a >>> T1 IMA circuit for dsl aggregation on that same circuit filling up >>> four >>> full T1 slots? Would this be a layer 2 local switching setup on the >>> pa-mc-t3 card? >>> >>> Otis >>> >>> >>> _______________________________________________ >>> cisco-nsp mailing list [email protected] >>> <mailto:[email protected]> >>> https://puck.nether.net/mailman/listinfo/cisco-nsp >>> archive at http://puck.nether.net/pipermail/cisco-nsp/ >>> >>> >>> >> _______________________________________________ >> cisco-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >> >> _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
