I could be wrong but I think you have your encapsulation wrong. interface ATM0/0 no ip address no ip mroute-cache no atm ilmi-keepalive dsl operating-mode auto pvc 0/35 encapsulation aal5mux ppp dialer dialer pool-member 1 ! !
----- Original Message ----- From: "Adam Greene" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Tuesday, October 02, 2007 10:58 AM Subject: [c-nsp] PPPoA DSL up/up, no traffic > Hi, > > I'm trying to configure a DSL line on a Cisco 1841 (C1841-IPBASE-M), > Version > 12.4(1c). > > The atm interface is plugged into a DSL line, it shows up/up, I have > packets > going out, but none coming back in. > > Do I have to do something in particular to initiate the connection? Are > there obvious errors with the config? Perhaps I need to contact the ISP. > > Disclaimer: this is the first DSL line I've ever configured (might be > obvious). > > Thanks for the help. > Adam > > > Here are the configurations so far, and some command / debug output: > > ======== > CONFIGS > ======== > > ! > aaa new-model > ! > aaa session-id common > ! > mmi polling-interval 60 > no mmi auto-configure > no mmi pvc > ! > interface FastEthernet0/0 > ip address x.x.x.x 255.255.252.0 > duplex auto > speed auto > ! > interface ATM0/0/0 > no ip address > no ip mroute-cache > no atm ilmi-keepalive > dsl operating-mode auto > hold-queue 224 in > pvc 0/35 > encapsulation aal5snap > protocol ppp dialer > dialer pool-member 1 > ! > interface Dialer1 > ip address negotiated > ip mtu 1492 > encapsulation ppp > no ip mroute-cache > dialer pool 1 > dialer idle-timeout 0 > dialer-group 1 > ppp authentication pap callin > ppp pap sent-username **** password 7 **** > ! > ip route 0.0.0.0 0.0.0.0 Dialer1 > ! > dialer-list 1 protocol ip permit > ! > end > > > ============= > SH INT ATM0/0/0 > ============= > > ATM0/0/0 is up, line protocol is up > Hardware is DSLSAR (with Alcatel ADSL Module) > MTU 4470 bytes, sub MTU 4470, BW 832 Kbit, DLY 610 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation ATM, loopback not set > Encapsulation(s): AAL5 AAL2, PVC mode > 23 maximum active VCs, 256 VCs per VP, 1 current VCCs > VC Auto Creation Disabled. > VC idle disconnect time: 300 seconds > Last input never, output 00:00:17, output hang never > Last clearing of "show interface" counters never > Input queue: 0/224/0/0 (size/max/drops/flushes); Total output drops: 0 > Queueing strategy: Per VC Queueing > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort > 66050 packets output, 1056800 bytes, 0 underruns > 0 output errors, 0 collisions, 0 interface resets > 0 output buffer failures, 0 output buffers swapped out > > ====================== > DEBUG PPP NEGOTIATION > ====================== > *Oct 2 15:51:10.173: %LINK-3-UPDOWN: Interface ATM0/0/0, changed state to > up > *Oct 2 15:51:13.173: %LINEPROTO-5-UPDOWN: Line protocol on Interface > ATM0/0/0, > changed state to up > *Oct 2 15:51:13.173: %LINK-3-UPDOWN: Interface Virtual-Access2, changed > state to up > *Oct 2 15:51:13.173: %DIALER-6-BIND: Interface Vi2 bound to profile Di1 > *Oct 2 15:51:13.173: Vi2 PPP: Using dialer call direction > *Oct 2 15:51:13.173: Vi2 PPP: Treating connection as a callout > *Oct 2 15:51:13.173: Vi2 PPP: Session handle[EF000004] Session id[2] > *Oct 2 15:51:13.173: Vi2 PPP: Phase is ESTABLISHING, Active Open > *Oct 2 15:51:13.173: Vi2 PPP: No remote authentication for call-out > *Oct 2 15:51:13.173: Vi2 LCP: O CONFREQ [Closed] id 173 len 10 > *Oct 2 15:51:13.173: Vi2 LCP: MagicNumber 0x2FA57203 (0x05062FA57203) > *Oct 2 15:51:15.161: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:51:15.161: Vi2 LCP: O CONFREQ [REQsent] id 174 len 10 > *Oct 2 15:51:15.161: Vi2 LCP: MagicNumber 0x2FA57203 (0x05062FA57203) > *Oct 2 15:51:17.177: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:51:17.177: Vi2 LCP: O CONFREQ [REQsent] id 175 len 10 > *Oct 2 15:51:17.177: Vi2 LCP: MagicNumber 0x2FA57203 (0x05062FA57203) > *Oct 2 15:51:19.193: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:51:19.193: Vi2 LCP: O CONFREQ [REQsent] id 176 len 10 > *Oct 2 15:51:19.193: Vi2 LCP: MagicNumber 0x2FA57203 (0x05062FA57203) > *Oct 2 15:51:21.209: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:51:21.209: Vi2 LCP: O CONFREQ [REQsent] id 177 len 10 > *Oct 2 15:51:21.209: Vi2 LCP: MagicNumber 0x2FA57203 (0x05062FA57203) > *Oct 2 15:51:23.225: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:51:23.225: Vi2 LCP: O CONFREQ [REQsent] id 178 len 10 > *Oct 2 15:51:23.225: Vi2 LCP: MagicNumber 0x2FA57203 (0x05062FA57203) > *Oct 2 15:51:25.241: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:51:25.241: Vi2 LCP: O CONFREQ [REQsent] id 179 len 10 > *Oct 2 15:51:25.241: Vi2 LCP: MagicNumber 0x2FA57203 (0x05062FA57203) > *Oct 2 15:51:27.257: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:51:27.257: Vi2 LCP: O CONFREQ [REQsent] id 180 len 10 > *Oct 2 15:51:27.257: Vi2 LCP: MagicNumber 0x2FA57203 (0x05062FA57203) > *Oct 2 15:51:29.273: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:51:29.273: Vi2 LCP: O CONFREQ [REQsent] id 181 len 10 > *Oct 2 15:51:29.273: Vi2 LCP: MagicNumber 0x2FA57203 (0x05062FA57203) > *Oct 2 15:51:31.289: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:51:31.289: Vi2 LCP: O CONFREQ [REQsent] id 182 len 10 > *Oct 2 15:51:31.289: Vi2 LCP: MagicNumber 0x2FA57203 (0x05062FA57203) > *Oct 2 15:51:33.305: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:51:33.305: Vi2 LCP: State is Listen > *Oct 2 15:52:03.321: Vi2 LCP: TIMEout: State Listen > *Oct 2 15:52:03.321: Vi2 PPP: No remote authentication for call-out > *Oct 2 15:52:03.321: Vi2 LCP: O CONFREQ [Listen] id 183 len 10 > *Oct 2 15:52:03.321: Vi2 LCP: MagicNumber 0x2FA635E8 (0x05062FA635E8) > *Oct 2 15:52:05.337: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:52:05.337: Vi2 LCP: O CONFREQ [REQsent] id 184 len 10 > *Oct 2 15:52:05.337: Vi2 LCP: MagicNumber 0x2FA635E8 (0x05062FA635E8) > *Oct 2 15:52:07.353: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:52:07.353: Vi2 LCP: O CONFREQ [REQsent] id 185 len 10 > *Oct 2 15:52:07.353: Vi2 LCP: MagicNumber 0x2FA635E8 (0x05062FA635E8) > *Oct 2 15:52:09.369: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:52:09.369: Vi2 LCP: O CONFREQ [REQsent] id 186 len 10 > *Oct 2 15:52:09.369: Vi2 LCP: MagicNumber 0x2FA635E8 (0x05062FA635E8) > *Oct 2 15:52:11.385: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:52:11.385: Vi2 LCP: O CONFREQ [REQsent] id 187 len 10 > *Oct 2 15:52:11.385: Vi2 LCP: MagicNumber 0x2FA635E8 (0x05062FA635E8) > *Oct 2 15:52:13.401: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:52:13.401: Vi2 LCP: O CONFREQ [REQsent] id 188 len 10 > *Oct 2 15:52:13.401: Vi2 LCP: MagicNumber 0x2FA635E8 (0x05062FA635E8) > *Oct 2 15:52:15.417: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:52:15.417: Vi2 LCP: O CONFREQ [REQsent] id 189 len 10 > *Oct 2 15:52:15.417: Vi2 LCP: MagicNumber 0x2FA635E8 (0x05062FA635E8) > *Oct 2 15:52:17.433: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:52:17.433: Vi2 LCP: O CONFREQ [REQsent] id 190 len 10 > *Oct 2 15:52:17.433: Vi2 LCP: MagicNumber 0x2FA635E8 (0x05062FA635E8) > *Oct 2 15:52:19.449: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:52:19.449: Vi2 LCP: O CONFREQ [REQsent] id 191 len 10 > *Oct 2 15:52:19.449: Vi2 LCP: MagicNumber 0x2FA635E8 (0x05062FA635E8) > *Oct 2 15:52:21.465: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:52:21.465: Vi2 LCP: O CONFREQ [REQsent] id 192 len 10 > *Oct 2 15:52:21.465: Vi2 LCP: MagicNumber 0x2FA635E8 (0x05062FA635E8) > *Oct 2 15:52:23.481: Vi2 LCP: TIMEout: State REQsent > *Oct 2 15:52:23.481: Vi2 LCP: State is Listen > > > ================= > DEBUG ATM EVENTS > ================= > *Oct 2 17:56:16.976: ATM0/0/0 check_lockup: scc = 0, output_qcount = 0, > head:(s)91, 92, > addr = (s)0x0, 0x0, count (s)67719, 67720 > *Oct 2 17:56:16.976: ATM0/0/0 check_lockup: scc = 1, output_qcount = 0, > head:(s)55, 55, > addr = (s)0x0, 0x0, count (s)112, 112 > *Oct 2 17:56:26.936: ATM0/0/0 check_lockup: scc = 0, output_qcount = 0, > head:(s)92, 92, > addr = (s)0x0, 0x0, count (s)67720, 67720 > *Oct 2 17:56:26.936: ATM0/0/0 check_lockup: scc = 1, output_qcount = 0, > head:(s)55, 55, > addr = (s)0x0, 0x0, count (s)112, 112 > *Oct 2 17:56:36.932: ATM0/0/0 check_lockup: scc = 0, output_qcount = 0, > head:(s)92, 92, > addr = (s)0x0, 0x0, count (s)67720, 67720 > *Oct 2 17:56:36.932: ATM0/0/0 check_lockup: scc = 1, output_qcount = 0, > head:(s)55, 55, > addr = (s)0x0, 0x0, count (s)112, 112 > > > > > > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
