Thanks Ziv. I think that's good advice since the compression took me from 123082 bytes to 20154 bytes.
Thanks again. -Nick > From: Ziv Leyes <[EMAIL PROTECTED]> > Date: Tue, 29 Apr 2008 10:15:51 +0300 > To: Nick Voth <[EMAIL PROTECTED]>, "[email protected]" > <[email protected]> > Conversation: Configuration buffer on 7206 > Subject: RE: Configuration buffer on 7206 > > > Perhaps you could copy the cerf_report to somewhere else and then delete it > from NVRAM, but as you can see, it's not taking up a lot of space so you > better leave them all alone, especially after the compress-config solved your > problem. > > Ziv > > > -----Original Message----- > From: Nick Voth [mailto:[EMAIL PROTECTED] > Sent: Tuesday, April 29, 2008 12:10 AM > To: Ziv Leyes; [email protected] > Subject: Re: Configuration buffer on 7206 > > Thanks Ziv. The comression works and here's the output of the dir nvram: > > Directory of nvram:/ > > 105 -rw- 20290 <no date> startup-config > 106 ---- 27 <no date> private-config > 107 -rw- 20290 <no date> underlying-config > 1 ---- 32 <no date> persistent-data > 2 -rw- 0 <no date> ifIndex-table > 3 -rw- 1661 <no date> cerf_report > > Is any of that expendable? > > Thanks, > > -Nick Voth > > >> From: Ziv Leyes <[EMAIL PROTECTED]> >> Date: Mon, 28 Apr 2008 23:52:40 +0300 >> To: Nick Voth <[EMAIL PROTECTED]>, "[email protected]" >> <[email protected]> >> Conversation: Configuration buffer on 7206 >> Subject: RE: Configuration buffer on 7206 >> >> Did you try using "service compress-config" on the global config? >> Also check what else do you have saved on the NVRAM, perhaps there is some >> unnecesary file that is taking up space >> Type dir nvram: and post us the output. >> Ziv >> >> ________________________________________ >> From: [EMAIL PROTECTED] [EMAIL PROTECTED] >> On >> Behalf Of Nick Voth [EMAIL PROTECTED] >> Sent: Monday, April 28, 2008 11:39 PM >> To: [email protected] >> Subject: [c-nsp] Configuration buffer on 7206 >> >> Hello folks, >> >> I just started running in to this error when doing a "copy run start" >> command on my 7206VXR: >> >> ============== >> copy run start >> Destination filename [startup-config]? >> Building configuration... >> >> % Warning: Saving this config to nvram may corrupt any network management or >> security files stored at the end of nvram. >> Continue? [no]: no >> % Configuration buffer full, can't add command: ntp clock-period 17179886 >> %Aborting Save. Compress the config, Save it to flash or Free up space on >> device[OK] >> ============== >> >> I've saved my running config to disk0 and to an off site FTP server, but I'm >> stumped about how to get the running config to be saved to the >> "startup-config" in nvram... >> >> Our config is pretty large because we have over 1000 VCI's configured on an >> ATM DS3 card. >> >> Any help would be wonderful! >> >> Thanks, >> >> -Nick Voth >> >> >> _______________________________________________ >> cisco-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >> >> >> >> >> >> *****************************************************************************>> * >> ****** >> This footnote confirms that this email message has been scanned by >> PineApp Mail-SeCure for the presence of malicious code, vandals & computer >> viruses. >> *****************************************************************************>> * >> ****** >> >> >> >> >> >> *****************************************************************************>> * >> ****** >> This footnote confirms that this email message has been scanned by >> PineApp Mail-SeCure for the presence of malicious code, vandals & computer >> viruses. >> *****************************************************************************>> * >> ****** >> >> >> > > > > > > > > ****************************************************************************** > ****** > This footnote confirms that this email message has been scanned by > PineApp Mail-SeCure for the presence of malicious code, vandals & computer > viruses. > ****************************************************************************** > ****** > > > > > ***************************************************************************** > ******* This footnote confirms that this email message has been scanned > by PineApp Mail-SeCure for the presence of malicious code, vandals & computer > viruses. ********************************************************************* > *************** _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
