On Tue, 17 Jun 2008, Pham, Loc wrote:
Another interesting command to explore is:
petach-tikva-gp#sho platfor hard capa fabr
Switch Fabric Resources
Bus utilization: current: 0%, peak was 8% at 09:10:06 IST Thu Feb 28
2008
Fabric utilization: Ingress Egress
Module Chanl Speed rate peak rate peak
1 0 8G 0% 3% @06:07 03Feb08 0% 15% @10:04
28Feb08
2 0 8G 0% 0% 0% 3% @06:43
03Feb08
3 0 8G 0% 3% @04:47 03Feb08 0% 7% @12:41
26Mar08
4 0 8G 0% 2% @17:01 17May08 0% 3% @21:58
03Feb08
7 0 20G 0% 12% @10:09 28Feb08 0% 6% @19:20
03Mar08
9 0 20G 0% 4% @12:32 03Feb08 0% 7% @16:13
11Feb08
9 1 20G 0% 3% @19:27 03Feb08 1% 11% @18:13
19Mar08
10 0 20G 0% 1% @10:41 09Feb08 0% 1% @05:57
03Feb08
10 1 20G 1% 6% @19:20 03Mar08 0% 7% @19:20
03Mar08
11 0 20G 1% 11% @10:51 12May08 1% 3% @11:23
27Mar08
Switching mode: Module Switching
mode
1
compact
2
compact
3
compact
4
compact
7
compact
9
compact
10
compact
11
compact
-Hank
Thanks Pete : this is what I have
sh fab sw
Global switching mode is Flow through
dCEF mode is not enforced for system to operate
Fabric module is not required for system to operate
Modules are allowed to operate in bus mode
Truncated mode is not allowed unless threshold is met
Threshold for truncated mode operation is 2 SFM-capable cards
Module Slot Switching Mode
1 Bus
2 Bus
3 Bus <<<< can be
--------------
I read about cycle the power ;-) thanks for the head up....
So I need to plan for a maint-window then. Since I have mix cards, I
need to use truncate mode, right ?
Regards,
Loc Pham, # 17030 R/S
"We switch our network dedicately :One packet at a time... "
-----Original Message-----
From: Peter Rathlev [mailto:[EMAIL PROTECTED]
Sent: Tuesday, June 17, 2008 2:27 PM
To: Pham, Loc
Cc: Cisco NSPs
Subject: Re: [c-nsp] fabric switching enable
On Tue, 2008-06-17 at 12:35 -0700, Pham, Loc wrote:
How can I identify whether our module is switched on mix mode and how
to change it ? any gotcha ?
xxx#sh fab sw mo all
Module Slot Switching Mode
1 Bus
2 Bus
3 Bus
XXX#sh fab sta
slot channel speed module fabric
status status
1 0 20G OK OK
You wouldn't happen to have a "fabric switching-mode force bus-mode" in
your running config?
Try doing a "show fabric switching-mode" without the "module all", it
gives some interesting lines in the beginning.
Changing switching mode power cycles the modules by the way. I guess
that's a gotcha. :-)
Regards,
Peter
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
