I'm sorry the auto template is only used in ios In XR you can specify the autoroute announce under attribute set And than use that with the group
adam -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of ?? Sent: Thursday, February 23, 2012 10:48 AM To: Oliver Boehmer (oboehmer) Cc: [email protected] Subject: Re: [c-nsp] MPLS TE conver from IOS to IOS-XR Hi Oil, Below is my whole config of the ASR9K, now the tunnel can up. mpls traffic-eng interface TenGigE0/0/0/0 ! interface TenGigE0/1/0/0.1700 ! auto-tunnel mesh group 1 destination-list 1 ! group 2 destination-list 2 ! tunnel-id min 1001 max 2000 ! auto-tunnel backup tunnel-id min 2001 max 3000 ! reoptimize 25 ! mpls ldp graceful-restart traffic-eng auto-tunnel mesh group 1 group 2 ! interface TenGigE0/0/0/0 ! interface TenGigE0/1/0/0.1700 ! router ospf 100 area 0.0.0.0 mpls traffic-eng mpls traffic-eng router-id Loopback0 But i don't find the autoroute-announce under traffic-engineering submode or under the group 1& 2. Many thanks. Hu Xu 在 2012年2月21日 下午7:38，Oliver Boehmer (oboehmer) <[email protected]>写道： > Hu,**** > > ** ** > > you indeed want to configure **** > > ** ** > > rsvp**** > > interface ..**** > > bandwidth …**** > > ** ** > > in order to be able to use non-zero banwdith reservations. That’s part of > your basic MPLS-TE config, which I didn’t include in my config example.. * > *** > > By default, the bandwidth is zero on interfaces enabled for MPLS-TE (i.e. > the ones enabled under “mpls traffic-eng”).. **** > > ** ** > > oli**** > > ** ** > > *From:* 许虎 [mailto:[email protected]] > *Sent:* 21 February 2012 10:03 > *To:* Oliver Boehmer (oboehmer) > *Cc:* [email protected] > > *Subject:* Re: [c-nsp] MPLS TE conver from IOS to IOS-XR**** > > ** ** > > The MPLS TE signaling usually uses the RSVP, but in the global > configuration i didn't see any RSVP configuration, why? Is the the default > configuraion? **** > > **** > > Many thanks.**** > > Hu Xu**** > > 在 2012年2月20日 下午9:03，Oliver Boehmer (oboehmer) <[email protected]>写道：**** > > ok.. you can also leave out the “autoroute-announce” for the beginning, > then the tunnel won’t take any traffic and you will be able to check if > everything is set up correctly (i.e. the primary/mesh tunnels are being > built and the backups are being installed), without any impact to the live > traffic..**** > > **** > > oli**** > > **** > > *From:* 许虎 [mailto:[email protected]] > *Sent:* 20 February 2012 14:00 > *To:* Oliver Boehmer (oboehmer) > *Subject:* Re: [c-nsp] MPLS TE conver from IOS to IOS-XR**** > > **** > > Thanks, oil, i will try in the live network tomorrow.**** > > 在 2012年2月20日 下午6:16，Oliver Boehmer (oboehmer) <[email protected]>写道：**** > > Hi,**** > > > > > Since now I can make sure the "Group" command in IOS-XR is the same to > the > > "Auto-Template" in IOS, but my problem is that in the IOS > "Auto-Template" I > > can use the below command : > > > > interface Auto-Template1 > > mpls mtu 17916 > > tunnel mpls traffic-eng autoroute announce > > tunnel mpls traffic-eng path-option 1 dynamic > > > > but in the Group, we just have the below command: > > > > XXXX(config-mpls-te)#auto-tunnel mesh > > XXXX(config-te-auto-mesh)#group 1 ? > > attribute-set Attribute-set name of type auto-mesh > > destination-list Destination-list (prefix-list) name > > disable Disable the mesh group > > <cr> > > > > So I am again wondering the group is not the same compared to the Auto- > > Template.**** > > you need to configure autoroute-announce and attribute-set, which you in > turn reference in the group.. look at the "autoroute announce" in the > config I sent. > As far as I know, path-option is always dynamic for auto-tunnel mesh in > XR, so no need to configure this. > > oli**** > > **** > > ** ** > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
