Yes, correct. One more thing, in the IOS we configure the " tunnel mpls traffic-eng path-option 1 dynamic" to automatic calculate the path, now in the IOS-XR, no more?
Thanks/Xu Hu 在 2012年2月23日 下午6:15，Vitkovsky, Adam <[email protected]>写道： > I'm sorry the auto template is only used in ios > In XR you can specify the autoroute announce under attribute set > And than use that with the group > > > adam > > -----Original Message----- > From: [email protected] [mailto: > [email protected]] On Behalf Of ?? > Sent: Thursday, February 23, 2012 10:48 AM > To: Oliver Boehmer (oboehmer) > Cc: [email protected] > Subject: Re: [c-nsp] MPLS TE conver from IOS to IOS-XR > > Hi Oil, > Below is my whole config of the ASR9K, now the tunnel can up. > > mpls traffic-eng > interface TenGigE0/0/0/0 > ! > interface TenGigE0/1/0/0.1700 > ! > auto-tunnel mesh > group 1 > destination-list 1 > ! > group 2 > destination-list 2 > ! > tunnel-id min 1001 max 2000 > ! > auto-tunnel backup > tunnel-id min 2001 max 3000 > ! > reoptimize 25 > ! > mpls ldp > graceful-restart > traffic-eng auto-tunnel mesh > group 1 > group 2 > ! > interface TenGigE0/0/0/0 > ! > interface TenGigE0/1/0/0.1700 > ! > router ospf 100 > area 0.0.0.0 > mpls traffic-eng > mpls traffic-eng router-id Loopback0 > But i don't find the autoroute-announce under traffic-engineering submode > or under the group 1& 2. > > Many thanks. > Hu Xu > > 在 2012年2月21日 下午7:38，Oliver Boehmer (oboehmer) <[email protected]>写道： > > > Hu,**** > > > > ** ** > > > > you indeed want to configure **** > > > > ** ** > > > > rsvp**** > > > > interface ..**** > > > > bandwidth …**** > > > > ** ** > > > > in order to be able to use non-zero banwdith reservations. That’s part of > > your basic MPLS-TE config, which I didn’t include in my config example.. > * > > *** > > > > By default, the bandwidth is zero on interfaces enabled for MPLS-TE (i.e. > > the ones enabled under “mpls traffic-eng”).. **** > > > > ** ** > > > > oli**** > > > > ** ** > > > > *From:* 许虎 [mailto:[email protected]] > > *Sent:* 21 February 2012 10:03 > > *To:* Oliver Boehmer (oboehmer) > > *Cc:* [email protected] > > > > *Subject:* Re: [c-nsp] MPLS TE conver from IOS to IOS-XR**** > > > > ** ** > > > > The MPLS TE signaling usually uses the RSVP, but in the global > > configuration i didn't see any RSVP configuration, why? Is the the > default > > configuraion? **** > > > > **** > > > > Many thanks.**** > > > > Hu Xu**** > > > > 在 2012年2月20日 下午9:03，Oliver Boehmer (oboehmer) <[email protected] > >写道：**** > > > > ok.. you can also leave out the “autoroute-announce” for the beginning, > > then the tunnel won’t take any traffic and you will be able to check if > > everything is set up correctly (i.e. the primary/mesh tunnels are being > > built and the backups are being installed), without any impact to the > live > > traffic..**** > > > > **** > > > > oli**** > > > > **** > > > > *From:* 许虎 [mailto:[email protected]] > > *Sent:* 20 February 2012 14:00 > > *To:* Oliver Boehmer (oboehmer) > > *Subject:* Re: [c-nsp] MPLS TE conver from IOS to IOS-XR**** > > > > **** > > > > Thanks, oil, i will try in the live network tomorrow.**** > > > > 在 2012年2月20日 下午6:16，Oliver Boehmer (oboehmer) <[email protected] > >写道：**** > > > > Hi,**** > > > > > > > > > Since now I can make sure the "Group" command in IOS-XR is the same to > > the > > > "Auto-Template" in IOS, but my problem is that in the IOS > > "Auto-Template" I > > > can use the below command : > > > > > > interface Auto-Template1 > > > mpls mtu 17916 > > > tunnel mpls traffic-eng autoroute announce > > > tunnel mpls traffic-eng path-option 1 dynamic > > > > > > but in the Group, we just have the below command: > > > > > > XXXX(config-mpls-te)#auto-tunnel mesh > > > XXXX(config-te-auto-mesh)#group 1 ? > > > attribute-set Attribute-set name of type auto-mesh > > > destination-list Destination-list (prefix-list) name > > > disable Disable the mesh group > > > <cr> > > > > > > So I am again wondering the group is not the same compared to the Auto- > > > Template.**** > > > > you need to configure autoroute-announce and attribute-set, which you in > > turn reference in the group.. look at the "autoroute announce" in the > > config I sent. > > As far as I know, path-option is always dynamic for auto-tunnel mesh in > > XR, so no need to configure this. > > > > oli**** > > > > **** > > > > ** ** > > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
