I know, but my situation is auto-tunnel mesh. Thanks and regards, Xu Hu
On 23 Feb, 2012, at 19:35, "Vitkovsky, Adam" <[email protected]> wrote: > In XR you’ll configure it the same - “path-option 1 dynamic” or “path-option > 1 explicit name” under the tunnel-te interface > > adam > ________________________________ > From: 许虎 [mailto:[email protected]] > Sent: Thursday, February 23, 2012 11:58 AM > To: Vitkovsky, Adam > Cc: Oliver Boehmer (oboehmer); [email protected] > Subject: Re: [c-nsp] MPLS TE conver from IOS to IOS-XR > > Yes, correct. One more thing, in the IOS we configure the " tunnel mpls > traffic-eng path-option 1 dynamic" to automatic calculate the path, now in > the IOS-XR, no more? > > Thanks/Xu Hu > 在 2012年2月23日 下午6:15，Vitkovsky, Adam > <[email protected]<mailto:[email protected]>>写道： > I'm sorry the auto template is only used in ios > In XR you can specify the autoroute announce under attribute set > And than use that with the group > > > adam > > -----Original Message----- > From: > [email protected]<mailto:[email protected]> > [mailto:[email protected]<mailto:[email protected]>] > On Behalf Of ?? > Sent: Thursday, February 23, 2012 10:48 AM > To: Oliver Boehmer (oboehmer) > Cc: [email protected]<mailto:[email protected]> > Subject: Re: [c-nsp] MPLS TE conver from IOS to IOS-XR > Hi Oil, > Below is my whole config of the ASR9K, now the tunnel can up. > > mpls traffic-eng > interface TenGigE0/0/0/0 > ! > interface TenGigE0/1/0/0.1700 > ! > auto-tunnel mesh > group 1 > destination-list 1 > ! > group 2 > destination-list 2 > ! > tunnel-id min 1001 max 2000 > ! > auto-tunnel backup > tunnel-id min 2001 max 3000 > ! > reoptimize 25 > ! > mpls ldp > graceful-restart > traffic-eng auto-tunnel mesh > group 1 > group 2 > ! > interface TenGigE0/0/0/0 > ! > interface TenGigE0/1/0/0.1700 > ! > router ospf 100 > area 0.0.0.0 > mpls traffic-eng > mpls traffic-eng router-id Loopback0 > But i don't find the autoroute-announce under traffic-engineering submode > or under the group 1& 2. > > Many thanks. > Hu Xu > > 在 2012年2月21日 下午7:38，Oliver Boehmer (oboehmer) > <[email protected]<mailto:[email protected]>>写道： >> Hu,**** >> >> ** ** >> >> you indeed want to configure **** >> >> ** ** >> >> rsvp**** >> >> interface ..**** >> >> bandwidth …**** >> >> ** ** >> >> in order to be able to use non-zero banwdith reservations. That’s part of >> your basic MPLS-TE config, which I didn’t include in my config example.. * >> *** >> >> By default, the bandwidth is zero on interfaces enabled for MPLS-TE (i.e. >> the ones enabled under “mpls traffic-eng”).. **** >> >> ** ** >> >> oli**** >> >> ** ** >> >> *From:* 许虎 [mailto:[email protected]<mailto:[email protected]>] >> *Sent:* 21 February 2012 10:03 >> *To:* Oliver Boehmer (oboehmer) >> *Cc:* [email protected]<mailto:[email protected]> >> >> *Subject:* Re: [c-nsp] MPLS TE conver from IOS to IOS-XR**** >> >> ** ** >> >> The MPLS TE signaling usually uses the RSVP, but in the global >> configuration i didn't see any RSVP configuration, why? Is the the default >> configuraion? **** >> >> **** >> >> Many thanks.**** >> >> Hu Xu**** >> >> 在 2012年2月20日 下午9:03，Oliver Boehmer (oboehmer) >> <[email protected]<mailto:[email protected]>>写道：**** >> >> ok.. you can also leave out the “autoroute-announce” for the beginning, >> then the tunnel won’t take any traffic and you will be able to check if >> everything is set up correctly (i.e. the primary/mesh tunnels are being >> built and the backups are being installed), without any impact to the live >> traffic..**** >> >> **** >> >> oli**** >> >> **** >> >> *From:* 许虎 [mailto:[email protected]<mailto:[email protected]>] >> *Sent:* 20 February 2012 14:00 >> *To:* Oliver Boehmer (oboehmer) >> *Subject:* Re: [c-nsp] MPLS TE conver from IOS to IOS-XR**** >> >> **** >> >> Thanks, oil, i will try in the live network tomorrow.**** >> >> 在 2012年2月20日 下午6:16，Oliver Boehmer (oboehmer) >> <[email protected]<mailto:[email protected]>>写道：**** >> >> Hi,**** >> >> >> >>> Since now I can make sure the "Group" command in IOS-XR is the same to >> the >>> "Auto-Template" in IOS, but my problem is that in the IOS >> "Auto-Template" I >>> can use the below command : >>> >>> interface Auto-Template1 >>> mpls mtu 17916 >>> tunnel mpls traffic-eng autoroute announce >>> tunnel mpls traffic-eng path-option 1 dynamic >>> >>> but in the Group, we just have the below command: >>> >>> XXXX(config-mpls-te)#auto-tunnel mesh >>> XXXX(config-te-auto-mesh)#group 1 ? >>> attribute-set Attribute-set name of type auto-mesh >>> destination-list Destination-list (prefix-list) name >>> disable Disable the mesh group >>> <cr> >>> >>> So I am again wondering the group is not the same compared to the Auto- >>> Template.**** >> >> you need to configure autoroute-announce and attribute-set, which you in >> turn reference in the group.. look at the "autoroute announce" in the >> config I sent. >> As far as I know, path-option is always dynamic for auto-tunnel mesh in >> XR, so no need to configure this. >> >> oli**** >> >> **** >> >> ** ** >> > _______________________________________________ > cisco-nsp mailing list > [email protected]<mailto:[email protected]> > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > > <winmail.dat> _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
