Hello everyone, The idea would be to do something like :
*interface bdi4093* * ip vrf forwarding TEST2* * ip address 172.31.0.253 255.255.255.0* * xconnect 1.1.1.1 10000 encapsulation mpls pw-class EOMPLS-ETH-TO-VLAN* But i'm not too sure if we can do this with an ASR... I may have to configure a vpls or something similar with vfi ? Thanks. # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - # - - Nicolas KARP # - - Network and Security Engineer # - - Email : [email protected] <[email protected]> # - - Linkedin : http://www.linkedin.com/in/nicolaskarp # - - Viadeo : http://www.viadeo.com/fr/profile/nicolas.karp <http://www.viadeo.com/fr/profile/nicolas.karp%20> # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2014-12-02 18:03 GMT+01:00 Nicolas KARP <[email protected]>: > Hi, > > I need to interconnect 2 platforms on 2 different datacenters. > > The idea is to create several EFPs on each PE (one at each side) and > create a default xconnect pw in order to encapsulate the layer2 traffic > over our MPLS network. I also have some layer 3 interfaces for different > vlans which need to be used on both datacenters : > > > *PE1 : (same config on PE2, except for the BDI interface)* > > > *interface GigabitEthernet0/0/4* > * no ip address* > * load-interval 30* > * negotiation auto* > > *## default XCONNECT to DC2* > * service instance 1 ethernet* > * encapsulation default* > * xconnect 1.1.1.1 9999 encapsulation mpls pw-class EOMPLS-ETH-TO-VLAN* > * !* > > *## Layer 3 interface via BDI* > * service instance 4093 ethernet* > * encapsulation dot1q 4093 exact* > * rewrite ingress tag pop 1 symmetric* > * bridge-domain 4093* > * !* > > *interface BDI4093* > * ip vrf forwarding TEST2* > * ip address 172.31.0.253 255.255.255.0* > * standby 1 ip 172.31.0.254* > * standby 1 priority 110* > * standby 1 preempt delay minimum 60* > *end* > > *--> I'm missing a xconnect for the vlan 4093...* > > > How can I create a layer3 interface and run a xconnect on the same EFP ? > The idea would be to use the same vlans at both locations and terminate the > Layer3 on a BDI interface in Datacenter1. > > Do you think it's possible ? > I'm not too sure if i'm really clear. Don't hesitate to ask me if you have > any questions :) > > Many Thanks for your help ! > > # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > - - - - - - - - - - - - - - - - - - - - > # - - Nicolas KARP > # - - Network and Security Engineer > # - - Email : [email protected] <[email protected]> > # - - Linkedin : http://www.linkedin.com/in/nicolaskarp > # - - Viadeo : http://www.viadeo.com/fr/profile/nicolas.karp > <http://www.viadeo.com/fr/profile/nicolas.karp%20> > # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > - - - - - - - - - - - - - - - - - - - - > > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
