I've found another thread where you were talking about router pw on an ASR1k.
He is the config i've done so far : *ASR 1001X : * l2 vfi TEST2 manual vpn id 258 bridge-domain 4093 neighbor 2.2.2.2 11 encapsulation mpls interface BDI4093 mtu 1530 ip vrf forwarding TEST2 ip address 172.31.0.253 255.255.255.0 standby 1 ip 172.31.0.254 standby 1 priority 110 standby 1 preempt delay minimum 60 end interface GigabitEthernet0/0/4 no ip address load-interval 30 negotiation auto service instance 4093 ethernet encapsulation dot1q 4093 exact rewrite ingress tag pop 1 symmetric bridge-domain 4093 ! *ISR 2801 : * interface FastEthernet0/1.4093 encapsulation dot1Q 4093 no cdp enable xconnect 1.1.1.1 11 encapsulation mpls // For some reason the xconnect is not coming up... RTI-MPLS-SAB-01#sh xconnect all DN pri vfi OCTEY UP mpls 2.2.2.2:11 DN UP pri bd 4093 UP vfi TEST2 UP Thanks for your help. # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - # - - Nicolas KARP # - - Network and Security Engineer # - - Email : [email protected] <[email protected]> # - - Linkedin : http://www.linkedin.com/in/nicolaskarp # - - Viadeo : http://www.viadeo.com/fr/profile/nicolas.karp <http://www.viadeo.com/fr/profile/nicolas.karp%20> # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2014-12-03 11:14 GMT+01:00 Nicolas KARP <[email protected]>: > Hi Adam, > > I don't have the xconnect command under the bdi interface : > > RTI-MPLS-SAB-01(config)#interface BDI4093 > RTI-MPLS-SAB-01(config-if)#xconnect ? > % Unrecognized command > > I'm using ASR1001X , ves 03.13.01.S > > > Any thought ? > > > > # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > - - - - - - - - - - - - - - - - - - - - > # - - Nicolas KARP > # - - Network and Security Engineer > # - - Email : [email protected] <[email protected]> > # - - Linkedin : http://www.linkedin.com/in/nicolaskarp > # - - Viadeo : http://www.viadeo.com/fr/profile/nicolas.karp > <http://www.viadeo.com/fr/profile/nicolas.karp%20> > # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > - - - - - - - - - - - - - - - - - - - - > > > > 2014-12-03 10:21 GMT+01:00 Vitkovský Adam <[email protected]>: > >> Hi Nicolas, >> >> This is the config for mixing EFPs and PWs in a common BD + IP interface >> for the BD. >> Manual hub and spoke type of configuration with IP address + VFR at the >> hub location. >> >> interface TenGigabitEthernet0/3 >> mtu 9000 >> service instance 8000 ethernet >> description CUSTOMER-B >> encapsulation dot1q 20,30,40 >> rewrite ingress tag pop 1 symmetric >> bridge-domain 8000 >> >> interface BDI8000 >> mtu 9000 >> vrf CUST-B >> ip add 192.0.2.1 255.255.255.0 >> xconnect vfi CUST-B-BD >> >> l2 vfi CUST-B-BD manual >> vpn id 1 >> neighbor 10.0.1.3 100 encapsulation mpls >> neighbor 10.0.1.4 200 encapsulation mpls >> neighbor 10.0.1.5 300 encapsulation mpls >> >> Spokes would have just EFPs with xconnect. >> >> >> adam >> > -----Original Message----- >> > From: cisco-nsp [mailto:[email protected]] On Behalf Of >> > Nicolas KARP >> > Sent: Tuesday, December 02, 2014 6:03 PM >> > To: [email protected] >> > Subject: [c-nsp] ASR 1K : EFP / XCONNECT / BDI >> > >> > Hi, >> > >> > I need to interconnect 2 platforms on 2 different datacenters. >> > >> > The idea is to create several EFPs on each PE (one at each side) and >> create a >> > default xconnect pw in order to encapsulate the layer2 traffic over our >> MPLS >> > network. I also have some layer 3 interfaces for different vlans which >> need to >> > be used on both datacenters : >> > >> > >> > *PE1 : (same config on PE2, except for the BDI interface)* >> > >> > >> > *interface GigabitEthernet0/0/4* >> > * no ip address* >> > * load-interval 30* >> > * negotiation auto* >> > >> > *## default XCONNECT to DC2* >> > * service instance 1 ethernet* >> > * encapsulation default* >> > * xconnect 1.1.1.1 9999 encapsulation mpls pw-class EOMPLS-ETH-TO-VLAN* >> > * !* >> > >> > *## Layer 3 interface via BDI* >> > * service instance 4093 ethernet* >> > * encapsulation dot1q 4093 exact* >> > * rewrite ingress tag pop 1 symmetric* >> > * bridge-domain 4093* >> > * !* >> > >> > *interface BDI4093* >> > * ip vrf forwarding TEST2* >> > * ip address 172.31.0.253 255.255.255.0* >> > * standby 1 ip 172.31.0.254* >> > * standby 1 priority 110* >> > * standby 1 preempt delay minimum 60* >> > *end* >> > >> > *--> I'm missing a xconnect for the vlan 4093...* >> > >> > >> > How can I create a layer3 interface and run a xconnect on the same EFP ? >> > The idea would be to use the same vlans at both locations and terminate >> the >> > Layer3 on a BDI interface in Datacenter1. >> > >> > Do you think it's possible ? >> > I'm not too sure if i'm really clear. Don't hesitate to ask me if you >> have any >> > questions :) >> > >> > Many Thanks for your help ! >> > >> > # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - >> - - >> > - - - - - - - - - - - - - - - - - - - >> > # - - Nicolas KARP >> > # - - Network and Security Engineer >> > # - - Email : [email protected] <[email protected]> >> > # - - Linkedin : http://www.linkedin.com/in/nicolaskarp >> > # - - Viadeo : http://www.viadeo.com/fr/profile/nicolas.karp >> > <http://www.viadeo.com/fr/profile/nicolas.karp%20> >> > # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - >> - - >> > - - - - - - - - - - - - - - - - - - - >> > _______________________________________________ >> > cisco-nsp mailing list [email protected] >> > https://puck.nether.net/mailman/listinfo/cisco-nsp >> > archive at http://puck.nether.net/pipermail/cisco-nsp/ >> > > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
