Does the MTU match on both ends please? You can see the MTU on both ends in the output of the cmd “sh mpls l2 vc det”
adam From: [email protected] [mailto:[email protected]] On Behalf Of Nicolas KARP Sent: Wednesday, December 03, 2014 12:29 PM To: Vitkovský Adam Cc: [email protected] Subject: Re: [c-nsp] ASR 1K : EFP / XCONNECT / BDI I've found another thread where you were talking about router pw on an ASR1k. He is the config i've done so far : ASR 1001X : l2 vfi TEST2 manual vpn id 258 bridge-domain 4093 neighbor 2.2.2.2 11 encapsulation mpls interface BDI4093 mtu 1530 ip vrf forwarding TEST2 ip address 172.31.0.253 255.255.255.0 standby 1 ip 172.31.0.254 standby 1 priority 110 standby 1 preempt delay minimum 60 end interface GigabitEthernet0/0/4 no ip address load-interval 30 negotiation auto service instance 4093 ethernet encapsulation dot1q 4093 exact rewrite ingress tag pop 1 symmetric bridge-domain 4093 ! ISR 2801 : interface FastEthernet0/1.4093 encapsulation dot1Q 4093 no cdp enable xconnect 1.1.1.1 11 encapsulation mpls // For some reason the xconnect is not coming up... RTI-MPLS-SAB-01#sh xconnect all DN pri vfi OCTEY UP mpls 2.2.2.2:11<http://2.2.2.2:11> DN UP pri bd 4093 UP vfi TEST2 UP Thanks for your help. # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - # - - Nicolas KARP # - - Network and Security Engineer # - - Email : [email protected]<mailto:[email protected]> # - - Linkedin : http://www.linkedin.com/in/nicolaskarp # - - Viadeo : http://www.viadeo.com/fr/profile/nicolas.karp <http://www.viadeo.com/fr/profile/nicolas.karp%20> # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2014-12-03 11:14 GMT+01:00 Nicolas KARP <[email protected]<mailto:[email protected]>>: Hi Adam, I don't have the xconnect command under the bdi interface : RTI-MPLS-SAB-01(config)#interface BDI4093 RTI-MPLS-SAB-01(config-if)#xconnect ? % Unrecognized command I'm using ASR1001X , ves 03.13.01.S Any thought ? # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - # - - Nicolas KARP # - - Network and Security Engineer # - - Email : [email protected]<mailto:[email protected]> # - - Linkedin : http://www.linkedin.com/in/nicolaskarp # - - Viadeo : http://www.viadeo.com/fr/profile/nicolas.karp <http://www.viadeo.com/fr/profile/nicolas.karp%20> # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2014-12-03 10:21 GMT+01:00 Vitkovský Adam <[email protected]<mailto:[email protected]>>: Hi Nicolas, This is the config for mixing EFPs and PWs in a common BD + IP interface for the BD. Manual hub and spoke type of configuration with IP address + VFR at the hub location. interface TenGigabitEthernet0/3 mtu 9000 service instance 8000 ethernet description CUSTOMER-B encapsulation dot1q 20,30,40 rewrite ingress tag pop 1 symmetric bridge-domain 8000 interface BDI8000 mtu 9000 vrf CUST-B ip add 192.0.2.1 255.255.255.0 xconnect vfi CUST-B-BD l2 vfi CUST-B-BD manual vpn id 1 neighbor 10.0.1.3 100 encapsulation mpls neighbor 10.0.1.4 200 encapsulation mpls neighbor 10.0.1.5 300 encapsulation mpls Spokes would have just EFPs with xconnect. adam > -----Original Message----- > From: cisco-nsp > [mailto:[email protected]<mailto:[email protected]>] > On Behalf Of > Nicolas KARP > Sent: Tuesday, December 02, 2014 6:03 PM > To: [email protected]<mailto:[email protected]> > Subject: [c-nsp] ASR 1K : EFP / XCONNECT / BDI > > Hi, > > I need to interconnect 2 platforms on 2 different datacenters. > > The idea is to create several EFPs on each PE (one at each side) and create a > default xconnect pw in order to encapsulate the layer2 traffic over our MPLS > network. I also have some layer 3 interfaces for different vlans which need to > be used on both datacenters : > > > *PE1 : (same config on PE2, except for the BDI interface)* > > > *interface GigabitEthernet0/0/4* > * no ip address* > * load-interval 30* > * negotiation auto* > > *## default XCONNECT to DC2* > * service instance 1 ethernet* > * encapsulation default* > * xconnect 1.1.1.1 9999 encapsulation mpls pw-class EOMPLS-ETH-TO-VLAN* > * !* > > *## Layer 3 interface via BDI* > * service instance 4093 ethernet* > * encapsulation dot1q 4093 exact* > * rewrite ingress tag pop 1 symmetric* > * bridge-domain 4093* > * !* > > *interface BDI4093* > * ip vrf forwarding TEST2* > * ip address 172.31.0.253 255.255.255.0* > * standby 1 ip 172.31.0.254* > * standby 1 priority 110* > * standby 1 preempt delay minimum 60* > *end* > > *--> I'm missing a xconnect for the vlan 4093...* > > > How can I create a layer3 interface and run a xconnect on the same EFP ? > The idea would be to use the same vlans at both locations and terminate the > Layer3 on a BDI interface in Datacenter1. > > Do you think it's possible ? > I'm not too sure if i'm really clear. Don't hesitate to ask me if you have any > questions :) > > Many Thanks for your help ! > > # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > - - - - - - - - - - - - - - - - - - - > # - - Nicolas KARP > # - - Network and Security Engineer > # - - Email : [email protected]<mailto:[email protected]> > <[email protected]<mailto:[email protected]>> > # - - Linkedin : http://www.linkedin.com/in/nicolaskarp > # - - Viadeo : http://www.viadeo.com/fr/profile/nicolas.karp > <http://www.viadeo.com/fr/profile/nicolas.karp%20> > # - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > - - - - - - - - - - - - - - - - - - - > _______________________________________________ > cisco-nsp mailing list > [email protected]<mailto:[email protected]> > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
