Try locking in the Codec on the inbound dialpeer.. there used to be a bug surrounding this...
On Fri, Feb 7, 2014 at 11:35 AM, <[email protected]> wrote: > It does work through PSTN. > > > > Here's the show output. > > > > ETUSSUNCME01#sh sdspfarm units > > > > conf-1 Device:confer1 TCP socket:[25] REGISTERED in SCCP ver 18/18 > > actual_stream:32 max_stream 32 IP:10.193.35.2 * 36967 Conference > Dixieland keepalive 744794 > > Supported codec: > > G711Ulaw > > G711Alaw > > G729 > > G729a > > G729b > > G729ab > > > > mtp-2 Device:xcode01 TCP socket:[100] REGISTERED in SCCP ver 18/18 > > actual_stream:14 max_stream 14 IP:10.193.35.2 * 39539 MTP Dixieland > keepalive 222496 > > Supported codec: > > G711Ulaw > > G711Alaw > > G729 > > G729a > > G729b > > G729ab > > > > *Zoltan Kelemen* > Global Communications and Information Security > Implementation Engineering > w: +40 374 132356 | m: +40 757 039093 > > > > *From:* Amit Kumar [mailto:[email protected]] > *Sent:* Friday, February 07, 2014 10:27 AM > *To:* Kelemen, Zoltan [CORP/RO] > > *Subject:* Re: [cisco-voip] Transcoding on a CME for a CUE > > > > Here is my 2 cents > > An "show sdspfarm units" will ensure if they are really registered. > > Have we tried calling cue pilot directly from pstn. To see if it's only > relevant to cfa. > > On 07-Feb-2014 8:00 pm, <[email protected]> wrote: > > Hi, > > Incoming codec is g.729. It does not show up in the config since that is > the default setting on a dial-peer. > > I'm well aware, that the two codecs differ, I have no choice (WAN is > strictly g729, CUE is g711 only). That is why I have transcoding set up, > see my original email in the thread. > I'm also aware that the call fails, because of codec mismatch. > > My problem is why? Why does the configured transcoding NOT work as > expected? > This will probably end up a TAC case early next week as I'm traveling > right now, just wanted to get some opinions if I was doing anything > obviously wrong and if I've missed something. > > Zoltan Kelemen > Global Communications and Information Security > Implementation Engineering > Emerson > > -----Original Message----- > From: cisco-voip [mailto:[email protected]] On Behalf Of > Andreas Sikkema > Sent: Friday, February 07, 2014 3:24 AM > To: [email protected] > Subject: Re: [cisco-voip] Transcoding on a CME for a CUE > > Zoltan, > > > The attached trace should have those debugs and more. > > > > > > > > Caller: +13***531042 > > Called: +19***465067 > > > > Forwarded to voicemail extension: 5110 > > Zoltan, the incoming call is G.729 only and all dialpeers in your config > appear to be G.711 only. > > > -- > Andreas Sikkema > _______________________________________________ > cisco-voip mailing list > [email protected] > https://puck.nether.net/mailman/listinfo/cisco-voip > > _______________________________________________ > cisco-voip mailing list > [email protected] > https://puck.nether.net/mailman/listinfo/cisco-voip > > _______________________________________________ > cisco-voip mailing list > [email protected] > https://puck.nether.net/mailman/listinfo/cisco-voip > >
_______________________________________________ cisco-voip mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-voip
