Hello,
John G. Heim, le lun. 09 févr. 2026 10:49:58 -0600, a ecrit:
> I am not sure what you guys are up to but if it helps, here is a udev rule
> that I think will load the DECtalk module for your DECtalk USB when you plug
> it in. Note: It matches the tty subsystem instead of USB because that way
> you can use "%k" to point Speakup at the device. Also, it sets action = add
> so that the rule is triggered only once. I have similar rules for my
> TripleTalk and for my Raspberry Pi synths.
>
> === begin
>
> ACTION=="add", \
> SUBSYSTEM=="tty", \
> ATTRS{idVendor}=="0dd0", \
> ATTRS{idProduct}=="2001", \
> RUN+="/sbin/modprobe speakup_dectlk tty=%k"
> === end
That's interesting for the list, but won't work in his case, since the
kernel driver is not recognizing this device as a ttyUSB0.
Thanks anyway,
Samuel
> On 2/8/26 3:45 PM, Chime Hart wrote:
> > OK Samuel, this is 90lines, hope it makes it through
> > sudo lsusb -v -d 0dd0:2001
> >
> > Bus 005 Device 004: ID 0dd0:2001 Access Solutions DECtalk USB
> > Negotiated speed: Full Speed (12Mbps)
> > Device Descriptor:
> > bLength 18
> > bDescriptorType 1
> > bcdUSB 1.00
> > bDeviceClass 0 [unknown]
> > bDeviceSubClass 0 [unknown]
> > bDeviceProtocol 0
> > bMaxPacketSize0 64
> > idVendor 0x0dd0 Access Solutions
> > idProduct 0x2001 DECtalk USB
> > bcdDevice 2.06
> > iManufacturer 1 Access Solutions
> > iProduct 2 DECtalk USB
> > iSerial 0
> > bNumConfigurations 1
> > Configuration Descriptor:
> > bLength 9
> > bDescriptorType 2
> > wTotalLength 0x0035
> > bNumInterfaces 1
> > bConfigurationValue 1
> > iConfiguration 0
> > bmAttributes 0xa0
> > (Bus Powered)
> > Remote Wakeup
> > MaxPower 400mA
> > Interface Descriptor:
> > bLength 9
> > bDescriptorType 4
> > bInterfaceNumber 0
> > bAlternateSetting 0
> > bNumEndpoints 5
> > bInterfaceClass 255 Vendor Specific Class
> > bInterfaceSubClass 0 [unknown]
> > bInterfaceProtocol 0
> > iInterface 0
> > Endpoint Descriptor:
> > bLength 7
> > bDescriptorType 5
> > bEndpointAddress 0x02 EP 2 OUT
> > bmAttributes 3
> > Transfer Type Interrupt
> > Synch Type None
> > Usage Type Data
> > wMaxPacketSize 0x0040 1x 64 bytes
> > bInterval 1
> > Endpoint Descriptor:
> > bLength 7
> > bDescriptorType 5
> > bEndpointAddress 0x04 EP 4 OUT
> > bmAttributes 3
> > Transfer Type Interrupt
> > Synch Type None
> > Usage Type Data
> > wMaxPacketSize 0x0040 1x 64 bytes
> > bInterval 1
> > Endpoint Descriptor:
> > bLength 7
> > bDescriptorType 5
> > bEndpointAddress 0x06 EP 6 OUT
> > bmAttributes 3
> > Transfer Type Interrupt
> > Synch Type None
> > Usage Type Data
> > wMaxPacketSize 0x0040 1x 64 bytes
> > bInterval 1
> > Endpoint Descriptor:
> > bLength 7
> > bDescriptorType 5
> > bEndpointAddress 0x86 EP 6 IN
> > bmAttributes 3
> > Transfer Type Interrupt
> > Synch Type None
> > Usage Type Data
> > wMaxPacketSize 0x0040 1x 64 bytes
> > bInterval 1
> > Endpoint Descriptor:
> > bLength 7
> > bDescriptorType 5
> > bEndpointAddress 0x84 EP 4 IN
> > bmAttributes 3
> > Transfer Type Interrupt
> > Synch Type None
> > Usage Type Data
> > wMaxPacketSize 0x0040 1x 64 bytes
> > bInterval 1
> > Device Status: 0x0000
> > (Bus Powered)
> > Chime
> >
> >
>
--
Samuel
"2 + 2 = 5 pour d'assez grandes valeurs de 2"
