I did a little test tonight on hot swapping between ABS colours, and the results turned out pretty decently:
https://pic.twitter.com/0ybanbLmKP https://pic.twitter.com/61b6oqfnpJ Note: These instructions assume that the ABS types are similar enough to have the same settings when generating gcode. The natural and black seemed to work fine with the settings we've been using so far. 1) Print until you wish to change colours 2) Immediately enter the following commands: PAUSE - Reverse 4mm (approx) - Go up 40 units on the Z axis. The reverse is so you don't spill over what you've printed already 3) Replace the filament with your second colour 4) extrude 20mm to make sure the new roll is loaded, using a pair of needle-nose pliers to keep anything from dripping onto your model. 5) resume the print 6) There is no step 6 WARNING: Never return the head to home while the printer is paused! When the print resumes, it reverses every action you performed to get back into position. What's the reverse of going to Z-Home? Burrowing down into the center of the earth, that's what. I had the print head crash into the bed today on account of the issue above - thankfully I had one hand on the kill switch. I re-taped and leveled the bed before printing again, it looks to be in perfect working order. Re-taping was probably overkill, but I figured it was time to clean it up a bit. - Jay / @Sporked On Wed, Oct 2, 2013 at 12:25 PM, Brian Kulyk <br...@kulyk.ca> wrote: > I just ordered us some more natural abs. > > > Brian Kulyk > 204.887.6988 > > > On Wed, Oct 2, 2013 at 8:21 AM, Stefan H.A <stefan...@gmail.com> wrote: >> >> We left it mounted to the top to avoid having to update the firmware. >> >> On 2013-10-02 8:16 AM, "Benjamin Bergman" <b...@benbergman.ca> wrote: >>> >>> Thanks a lot, guys! Just curious, is the switch still mounted at the >>> top, or did you try mounting the new switch at the bottom? >>> >>> On Tue, Oct 1, 2013 at 11:18 PM, Brian Kulyk <br...@kulyk.ca> wrote: >>> > Thanks to the amazing help from Stephan, Dr. West, Aemilianus and Thor >>> > we >>> > managed to get the new mechanical switch in place and homing properly. >>> > It >>> > looks to be working great and people should be able to use the printer >>> > again, but it looks like the print bed will require some additional >>> > leveling. Small parts in the center of the bed should be fine, but you >>> > may >>> > experience warping in larger parts. >>> > >>> > Thanks again to everyone who has helped get the printer running again! >>> > Amazing team work. >>> > >>> > >>> > Brian Kulyk >>> > 204.887.6988 >>> > >>> > >>> > On Tue, Oct 1, 2013 at 3:47 PM, Brian Kulyk <br...@kulyk.ca> wrote: >>> >> >>> >> I bought one this afternoon, I will bring it to the meeting today. >>> >> >>> >> >>> >> Brian Kulyk >>> >> 204.887.6988 >>> >> >>> >> >>> >> On Tue, Oct 1, 2013 at 2:45 PM, Stefan H.A <stefan...@gmail.com> >>> >> wrote: >>> >>> >>> >>> I believe there are some at the space(can anyone confirm). If not I >>> >>> have >>> >>> some at home. I can stop there and grab a couple on my way to the >>> >>> meeting. >>> >>> >>> >>> On 2013-10-01 2:33 PM, "Benjamin Bergman" <b...@benbergman.ca> wrote: >>> >>>> >>> >>>> Ya, I think my vote is for the microswitch as well, but I'll toss a >>> >>>> couple hall effect sensors in with my order so we can fix up the >>> >>>> other >>> >>>> board in case we want to use it again. Do we have extra >>> >>>> microswitches, >>> >>>> or should I grab a few of those too? >>> >>>> >>> >>>> On Tue, Oct 1, 2013 at 2:06 PM, Stefan H.A <stefan...@gmail.com> >>> >>>> wrote: >>> >>>> > Yeah, I think a micro switch (as picture in the link in the IRC >>> >>>> > conversation) will work fine. We could use an opto-interupter ( >>> >>>> > >>> >>>> > >>> >>>> > http://www.jameco.com/1/1/25649-h21a1-opto-electronic-interrupter-switch-transistor-sensors.html >>> >>>> > ) if we want to get fancy but I think a microswitch will work just >>> >>>> > as >>> >>>> > well. >>> >>>> > >>> >>>> > On 2013-10-01 1:48 PM, "Brian Kulyk" <br...@kulyk.ca> wrote: >>> >>>> >> >>> >>>> >> I was looking on Digikey for the sensor we need and noticed many >>> >>>> >> different >>> >>>> >> versions so I decided to contact Maker's Tool Works to find out >>> >>>> >> the >>> >>>> >> specifics of the sensor they used. They (as well as the folks on >>> >>>> >> IRC) >>> >>>> >> suggest using a mechanical switch. Eventually I found that this >>> >>>> >> is >>> >>>> >> the >>> >>>> >> part we need if we want to continue using the hall effect sensor. >>> >>>> >> >>> >>>> >> >>> >>>> >> http://www.digikey.ca/product-detail/en/TLE4905L%20E6433/TLE4905LE6433INCT-ND/1650234 >>> >>>> >> >>> >>>> >> If we decide to order these we should get a few backups. Ben, >>> >>>> >> it's >>> >>>> >> not >>> >>>> >> too late to combine with your order that would be great. I can >>> >>>> >> give >>> >>>> >> you >>> >>>> >> some cash for the order tonight at the meeting. >>> >>>> >> >>> >>>> >> ME: >>> >>>> >> >>> >>>> >>> >>> >>>> >>> I have broken the sensor off of the "Cheep O" board. I would >>> >>>> >>> order >>> >>>> >>> another one from you, but the store appears to be about can I >>> >>>> >>> please >>> >>>> >>> get >>> >>>> >>> some additional information about the sensor so I can order a >>> >>>> >>> replacement >>> >>>> >>> elsewhere. >>> >>>> >> >>> >>>> >> >>> >>>> >> Maker's Tool Works >>> >>>> >> >>> >>>> >>> Unfortunately we are not expecting to have them back in stock >>> >>>> >>> for >>> >>>> >>> quiet a >>> >>>> >>> while. You're kit should have another mechanical endstop. All >>> >>>> >>> current kits >>> >>>> >>> do not have a cheap-o and we are finding the mechanical just as >>> >>>> >>> effective. >>> >>>> >>> The Cheap-o hall endsop is designed by BLDDK, I have seen one >>> >>>> >>> clone >>> >>>> >>> online >>> >>>> >>> and some diy versions on thingiverse. >>> >>>> >> >>> >>>> >> >>> >>>> >> I found that I can order a replacement board from here: >>> >>>> >> http://www.elecfreaks.com/store/hall-endstop-p-654.html Though >>> >>>> >> it >>> >>>> >> does look >>> >>>> >> a little different they are both based off the BLDDK's design. >>> >>>> >> >>> >>>> >> Chat log from IRC: >>> >>>> >> >>> >>>> >>>> [11:48] <grumpy> I broke the sensor off of my cheap-o hall z >>> >>>> >>>> endstop. >>> >>>> >>>> Can anybody tell me where I can order a replacement (the >>> >>>> >>>> official >>> >>>> >>>> store is >>> >>>> >>>> sold out). >>> >>>> >>>> >>> >>>> >>>> [11:48] <skywurz> grumpy i too did that >>> >>>> >>>> >>> >>>> >>>> [11:48] <skywurz> grumpy i dont like that sensor >>> >>>> >>>> >>> >>>> >>>> [11:49] <grumpy> skywurz what are you using now? >>> >>>> >>>> >>> >>>> >>>> [11:49] <skywurz> grumpy may i recommend >>> >>>> >>>> http://www.wuala.com/skywurz/Public/IMG_20130519_122911.jpg/ >>> >>>> >>>> >>> >>>> >>>> [11:51] <grumpy> skywurz I was thinking of going with something >>> >>>> >>>> like >>> >>>> >>>> that, but others were worried that it might not be as accurate >>> >>>> >>>> as >>> >>>> >>>> the >>> >>>> >>>> hall-effect thing, I take you are not having any troubles with >>> >>>> >>>> your >>> >>>> >>>> replacement? >>> >>>> >>>> >>> >>>> >>>> [11:51] <skywurz> grumpy it really does not make that much of a >>> >>>> >>>> difference >>> >>>> >>>> >>> >>>> >>>> [11:52] <skywurz> think about how far off you could have thrown >>> >>>> >>>> that >>> >>>> >>>> cheap-o off by bumping the sensor >>> >>>> >>>> >>> >>>> >>>> [11:54] <grumpy> skywurz Sounds good I will give it shot. I >>> >>>> >>>> already >>> >>>> >>>> printed off a bracket to use a switch like that anyway. >>> >>>> >>>> >>> >>>> >>>> [11:54] <skywurz> never answered my imagineer question >>> >>>> >>>> >>> >>>> >>>> [11:54] <skywurz> grumpy sweet >>> >>>> >>>> >>> >>>> >>>> [11:54] <skywurz> grumpy if you have no interest in saving the >>> >>>> >>>> old >>> >>>> >>>> cheap >>> >>>> >>>> o you can re use the wires on it >>> >>>> >> >>> >>>> >> >>> >>>> >> >>> >>>> >> >>> >>>> >> Brian Kulyk >>> >>>> >> 204.887.6988 >>> >>>> >> >>> >>>> >> >>> >>>> >> On Sat, Sep 28, 2013 at 7:11 PM, Benjamin Bergman >>> >>>> >> <b...@benbergman.ca> >>> >>>> >> wrote: >>> >>>> >>> >>> >>>> >>> I just took a look at the sensor and I doubt it can be >>> >>>> >>> resoldered. I >>> >>>> >>> was about to get some stuff from digikey, so we can toss a few >>> >>>> >>> sensors >>> >>>> >>> into that order as well. Shipping isn't much and it arrives >>> >>>> >>> fast. >>> >>>> >>> I'm >>> >>>> >>> just not sure when our order is going out (should be this week >>> >>>> >>> though). >>> >>>> >>> >>> >>>> >>> On Sat, Sep 28, 2013 at 3:38 PM, Brian Kulyk <br...@kulyk.ca> >>> >>>> >>> wrote: >>> >>>> >>> > I just broke off the board, one of the leads is now really >>> >>>> >>> > small. >>> >>>> >>> > Someone >>> >>>> >>> > might be able to solder it back together, but it's beyond my >>> >>>> >>> > skill >>> >>>> >>> > level. >>> >>>> >>> > >>> >>>> >>> > I found a mount for a physical switch on thingiverse, we could >>> >>>> >>> > try >>> >>>> >>> > that >>> >>>> >>> > until the new sensor gets here or until someone with more >>> >>>> >>> > skill >>> >>>> >>> > than I >>> >>>> >>> > can >>> >>>> >>> > re-solder the old one. >>> >>>> >>> > >>> >>>> >>> > >>> >>>> >>> > >>> >>>> >>> > >>> >>>> >>> > Brian Kulyk >>> >>>> >>> > 204.887.6988 >>> >>>> >>> > >>> >>>> >>> > >>> >>>> >>> > On Sat, Sep 28, 2013 at 3:19 PM, Stefan H.A >>> >>>> >>> > <stefan...@gmail.com> >>> >>>> >>> > wrote: >>> >>>> >>> >> >>> >>>> >>> >> Yeah that will likely work. I've been looking for a schematic >>> >>>> >>> >> for >>> >>>> >>> >> that >>> >>>> >>> >> board to ensure the hall effect sensor is the same as the one >>> >>>> >>> >> sold at >>> >>>> >>> >> sparkfun but can't seem to find it using my phone though. >>> >>>> >>> >> Odds >>> >>>> >>> >> are >>> >>>> >>> >> very good >>> >>>> >>> >> they are equivalent. >>> >>>> >>> >> >>> >>>> >>> >> Did the actual sensor break or did it just break off the >>> >>>> >>> >> board. >>> >>>> >>> >> If it >>> >>>> >>> >> just >>> >>>> >>> >> broke off the board maybe we can reattach it. >>> >>>> >>> >> >>> >>>> >>> >> On 2013-09-28 2:19 PM, "Brian Kulyk" <br...@kulyk.ca> wrote: >>> >>>> >>> >>> >>> >>>> >>> >>> Unfortunately maker stool works is out of the "Cheap-O Hall >>> >>>> >>> >>> Endstop >>> >>>> >>> >>> Sensor". Perhaps I can just order a new sensor from >>> >>>> >>> >>> sparkfun >>> >>>> >>> >>> and >>> >>>> >>> >>> solder it >>> >>>> >>> >>> onto the existing board. >>> >>>> >>> >>> >>> >>>> >>> >>> Thoughts? >>> >>>> >>> >>> >>> >>>> >>> >>> >>> >>>> >>> >>> Brian Kulyk >>> >>>> >>> >>> 204.887.6988 >>> >>>> >>> >>> >>> >>>> >>> >>> >>> >>>> >>> >>> On Sat, Sep 28, 2013 at 2:07 PM, Stefan H.A >>> >>>> >>> >>> <stefan...@gmail.com> >>> >>>> >>> >>> wrote: >>> >>>> >>> >>>> >>> >>>> >>> >>>> If we are ordering something from makerstoolworks.com maybe >>> >>>> >>> >>>> we >>> >>>> >>> >>>> should >>> >>>> >>> >>>> see if anything changed from the beta kit we got and have >>> >>>> >>> >>>> that >>> >>>> >>> >>>> included in >>> >>>> >>> >>>> the shipment. Also I think there were some parts that were >>> >>>> >>> >>>> not >>> >>>> >>> >>>> right >>> >>>> >>> >>>> in the >>> >>>> >>> >>>> original kit we might like to get replaced. >>> >>>> >>> >>>> >>> >>>> >>> >>>> On 2013-09-28 1:37 PM, "Stefan H.A" <stefan...@gmail.com> >>> >>>> >>> >>>> wrote: >>> >>>> >>> >>>>> >>> >>>> >>> >>>>> If you are going to use the 'peice of paper' method you >>> >>>> >>> >>>>> need >>> >>>> >>> >>>>> to >>> >>>> >>> >>>>> remove >>> >>>> >>> >>>>> homing lines from custom gcode section of the slicer >>> >>>> >>> >>>>> config. I >>> >>>> >>> >>>>> beleive the >>> >>>> >>> >>>>> appropriate lines are g28 and g92 z183. >>> >>>> >>> >>>>> >>> >>>> >>> >>>>> On 2013-09-28 1:30 PM, "Stefan H.A" <stefan...@gmail.com> >>> >>>> >>> >>>>> wrote: >>> >>>> >>> >>>>>> >>> >>>> >>> >>>>>> We got the end stop with the kit. A replacement should be >>> >>>> >>> >>>>>> available >>> >>>> >>> >>>>>> from makerstoolworks.com. A microswitch could also be >>> >>>> >>> >>>>>> used if >>> >>>> >>> >>>>>> we >>> >>>> >>> >>>>>> can figure >>> >>>> >>> >>>>>> a way to attach it. In the mean time we can still use the >>> >>>> >>> >>>>>> "piece >>> >>>> >>> >>>>>> of paper" >>> >>>> >>> >>>>>> method of zeroing. If you need a refresher check old >>> >>>> >>> >>>>>> revisions of >>> >>>> >>> >>>>>> the wiki. >>> >>>> >>> >>>>>> >>> >>>> >>> >>>>>> This should not have happened. Is it possible the endstop >>> >>>> >>> >>>>>> came >>> >>>> >>> >>>>>> disconnected? I suppose the firmware could have gone >>> >>>> >>> >>>>>> insane >>> >>>> >>> >>>>>> when >>> >>>> >>> >>>>>> it froze up >>> >>>> >>> >>>>>> and that is why it didn't obey the endstop. In the >>> >>>> >>> >>>>>> future, we >>> >>>> >>> >>>>>> should >>> >>>> >>> >>>>>> probably completely power down and disconnect the usb >>> >>>> >>> >>>>>> cable >>> >>>> >>> >>>>>> when >>> >>>> >>> >>>>>> recovering >>> >>>> >>> >>>>>> from a crash to ensure the firmware gets reset. This now >>> >>>> >>> >>>>>> makes me >>> >>>> >>> >>>>>> wonder if >>> >>>> >>> >>>>>> the freezing problem is caused by the firmware and not >>> >>>> >>> >>>>>> the >>> >>>> >>> >>>>>> computer. Maybe >>> >>>> >>> >>>>>> we should see if any other user are reporting this and >>> >>>> >>> >>>>>> check >>> >>>> >>> >>>>>> if >>> >>>> >>> >>>>>> there is a >>> >>>> >>> >>>>>> more recent version of the Marlin firmware. >>> >>>> >>> >>>>>> >>> >>>> >>> >>>>>> On 2013-09-28 1:05 PM, "Brian Kulyk" <br...@kulyk.ca> >>> >>>> >>> >>>>>> wrote: >>> >>>> >>> >>>>>>> >>> >>>> >>> >>>>>>> Somehow I managed to break the z axis end-stop sensor. >>> >>>> >>> >>>>>>> I >>> >>>> >>> >>>>>>> was >>> >>>> >>> >>>>>>> printing this morning, and the print failed. I hit the >>> >>>> >>> >>>>>>> button to >>> >>>> >>> >>>>>>> disconnect, and reconnected to the printer then hit the >>> >>>> >>> >>>>>>> z >>> >>>> >>> >>>>>>> home >>> >>>> >>> >>>>>>> button so I >>> >>>> >>> >>>>>>> could remove the failed print. The z axis did NOT stop >>> >>>> >>> >>>>>>> at 0, >>> >>>> >>> >>>>>>> it >>> >>>> >>> >>>>>>> kept going >>> >>>> >>> >>>>>>> and broke a little black piece off of the z end-stop >>> >>>> >>> >>>>>>> sensor. >>> >>>> >>> >>>>>>> >>> >>>> >>> >>>>>>> If someone can tell me where we got the sensor from I >>> >>>> >>> >>>>>>> can go >>> >>>> >>> >>>>>>> and >>> >>>> >>> >>>>>>> get >>> >>>> >>> >>>>>>> or order us another one as soon as possible. >>> >>>> >>> >>>>>>> >>> >>>> >>> >>>>>>> Sorry for the inconvenience. >>> >>>> >>> >>>>>>> >>> >>>> >>> >>>>>>> >>> >>>> >>> >>>>>>> >>> >>>> >>> >>>>>>> Brian Kulyk >>> >>>> >>> >>>>>>> 204.887.6988 >>> >>>> >>> >>>>>>> >>> >>>> >>> >>>>>>> >>> >>>> >>> >>>>>>> On Fri, Sep 27, 2013 at 4:33 PM, Stefan H.A >>> >>>> >>> >>>>>>> <stefan...@gmail.com> >>> >>>> >>> >>>>>>> wrote: >>> >>>> >>> >>>>>>>> >>> >>>> >>> >>>>>>>> Yeah, I think slowing down more and using the fan >>> >>>> >>> >>>>>>>> less(read: >>> >>>> >>> >>>>>>>> almost >>> >>>> >>> >>>>>>>> never) is the solution to the cracks we are getting in >>> >>>> >>> >>>>>>>> some >>> >>>> >>> >>>>>>>> parts. >>> >>>> >>> >>>>>>>> >>> >>>> >>> >>>>>>>> On 2013-09-27 3:12 PM, "d-_-b" >>> >>>> >>> >>>>>>>> <thor.robin...@gmail.com> >>> >>>> >>> >>>>>>>> wrote: >>> >>>> >>> >>>>>>>>> >>> >>>> >>> >>>>>>>>> Parts with fine detail can be run with a lower minimum >>> >>>> >>> >>>>>>>>> speed ( >>> >>>> >>> >>>>>>>>> default 10mm/s ). we ran the second triforce at 1mm/s >>> >>>> >>> >>>>>>>>> minimum >>> >>>> >>> >>>>>>>>> speed and that >>> >>>> >>> >>>>>>>>> was a tad low, but gave us excellent detail. >>> >>>> >>> >>>>>>>>> >>> >>>> >>> >>>>>>>>> >>> >>>> >>> >>>>>>>>> On Fri, Sep 27, 2013 at 10:36 AM, Stefan H.A >>> >>>> >>> >>>>>>>>> <stefan...@gmail.com> >>> >>>> >>> >>>>>>>>> wrote: >>> >>>> >>> >>>>>>>>>> >>> >>>> >>> >>>>>>>>>> I've added some useful links to the tuning section of >>> >>>> >>> >>>>>>>>>> 3d >>> >>>> >>> >>>>>>>>>> printer >>> >>>> >>> >>>>>>>>>> wiki page. >>> >>>> >>> >>>>>>>>>> >>> >>>> >>> >>>>>>>>>> Based on the 'too cold' section of the trouble >>> >>>> >>> >>>>>>>>>> shooting >>> >>>> >>> >>>>>>>>>> guide >>> >>>> >>> >>>>>>>>>> I >>> >>>> >>> >>>>>>>>>> beleive we are cooling the part too much with the >>> >>>> >>> >>>>>>>>>> fan. I >>> >>>> >>> >>>>>>>>>> think >>> >>>> >>> >>>>>>>>>> that when >>> >>>> >>> >>>>>>>>>> printing with ABS the fan should remain off unless >>> >>>> >>> >>>>>>>>>> absolutely >>> >>>> >>> >>>>>>>>>> necessary (ie. >>> >>>> >>> >>>>>>>>>> Very short layers). Thinking back to the triforce, it >>> >>>> >>> >>>>>>>>>> only had >>> >>>> >>> >>>>>>>>>> trouble at >>> >>>> >>> >>>>>>>>>> the very top where the layers were taking only few >>> >>>> >>> >>>>>>>>>> seconds. >>> >>>> >>> >>>>>>>>>> >>> >>>> >>> >>>>>>>>>> On 2013-09-26 12:14 AM, "Stefan H.A" >>> >>>> >>> >>>>>>>>>> <stefan...@gmail.com> >>> >>>> >>> >>>>>>>>>> wrote: >>> >>>> >>> >>>>>>>>>>> >>> >>>> >>> >>>>>>>>>>> Be advised, I changed the infill patern to >>> >>>> >>> >>>>>>>>>>> honeycomb. >>> >>>> >>> >>>>>>>>>>> Don't >>> >>>> >>> >>>>>>>>>>> be >>> >>>> >>> >>>>>>>>>>> alarmed if the printer appears to have a convulsion >>> >>>> >>> >>>>>>>>>>> while >>> >>>> >>> >>>>>>>>>>> printing infill. >>> >>>> >>> >>>>>>>>>>> Do keep an eye out for screws coming loose. >>> >>>> >>> >>>>>>>>>>> >>> >>>> >>> >>>>>>>>>>> I've also set it to print a solid layer every 40 >>> >>>> >>> >>>>>>>>>>> layers. >>> >>>> >>> >>>>>>>>>>> These >>> >>>> >>> >>>>>>>>>>> settings should increase part strength considerably. >>> >>>> >>> >>>>>>>>>>> >>> >>>> >>> >>>>>>>>>>> On 2013-09-24 3:39 PM, "Benjamin Bergman" >>> >>>> >>> >>>>>>>>>>> <b...@benbergman.ca> >>> >>>> >>> >>>>>>>>>>> wrote: >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>>>>>>>>>> The second one I linked >>> >>>> >>> >>>>>>>>>>>> (http://www.thingiverse.com/thing:124533) is >>> >>>> >>> >>>>>>>>>>>> basically a proper version of the one that I >>> >>>> >>> >>>>>>>>>>>> cobbled >>> >>>> >>> >>>>>>>>>>>> together >>> >>>> >>> >>>>>>>>>>>> months >>> >>>> >>> >>>>>>>>>>>> ago that we are currently using. No disassembly >>> >>>> >>> >>>>>>>>>>>> required to >>> >>>> >>> >>>>>>>>>>>> install >>> >>>> >>> >>>>>>>>>>>> that one. >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>>>>>>>>>> It would have been nice if all their end plates had >>> >>>> >>> >>>>>>>>>>>> cutouts >>> >>>> >>> >>>>>>>>>>>> for >>> >>>> >>> >>>>>>>>>>>> t-nuts >>> >>>> >>> >>>>>>>>>>>> to be inserted, like the main back plate has. It >>> >>>> >>> >>>>>>>>>>>> would >>> >>>> >>> >>>>>>>>>>>> make >>> >>>> >>> >>>>>>>>>>>> upgrading >>> >>>> >>> >>>>>>>>>>>> things way easier. >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>>>>>>>>>> On Tue, Sep 24, 2013 at 3:18 PM, Stefan H.A >>> >>>> >>> >>>>>>>>>>>> <stefan...@gmail.com> wrote: >>> >>>> >>> >>>>>>>>>>>> > Depending where the bracket attaches, the printer >>> >>>> >>> >>>>>>>>>>>> > may >>> >>>> >>> >>>>>>>>>>>> > need >>> >>>> >>> >>>>>>>>>>>> > to >>> >>>> >>> >>>>>>>>>>>> > be partially >>> >>>> >>> >>>>>>>>>>>> > disassembled to add the t-nuts into the channels >>> >>>> >>> >>>>>>>>>>>> > (looks >>> >>>> >>> >>>>>>>>>>>> > like >>> >>>> >>> >>>>>>>>>>>> > that may be the >>> >>>> >>> >>>>>>>>>>>> > case for the top most screw). I have been looking >>> >>>> >>> >>>>>>>>>>>> > for >>> >>>> >>> >>>>>>>>>>>> > a >>> >>>> >>> >>>>>>>>>>>> > solution that only >>> >>>> >>> >>>>>>>>>>>> > needs t-nuts in accessable channels. >>> >>>> >>> >>>>>>>>>>>> > >>> >>>> >>> >>>>>>>>>>>> > On 2013-09-24 3:09 PM, "Brian Kulyk" >>> >>>> >>> >>>>>>>>>>>> > <br...@kulyk.ca> >>> >>>> >>> >>>>>>>>>>>> > wrote: >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> I like the first one Ben suggested >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> (http://www.thingiverse.com/thing:77301/#remixes) >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> Brian Kulyk >>> >>>> >>> >>>>>>>>>>>> >> 204.887.6988 >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> On Tue, Sep 24, 2013 at 1:50 PM, Benjamin >>> >>>> >>> >>>>>>>>>>>> >> Bergman >>> >>>> >>> >>>>>>>>>>>> >> <b...@benbergman.ca> >>> >>>> >>> >>>>>>>>>>>> >> wrote: >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> A few more options (all designed to attach to >>> >>>> >>> >>>>>>>>>>>> >>> the >>> >>>> >>> >>>>>>>>>>>> >>> MendelMax >>> >>>> >>> >>>>>>>>>>>> >>> 2.0): >>> >>>> >>> >>>>>>>>>>>> >>> http://www.thingiverse.com/thing:77301/#remixes >>> >>>> >>> >>>>>>>>>>>> >>> http://www.thingiverse.com/thing:124533 >>> >>>> >>> >>>>>>>>>>>> >>> http://www.thingiverse.com/thing:78741 >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> On Tue, Sep 24, 2013 at 12:33 PM, Stefan H.A >>> >>>> >>> >>>>>>>>>>>> >>> <stefan...@gmail.com> wrote: >>> >>>> >>> >>>>>>>>>>>> >>> > This would probably work but a stand alone >>> >>>> >>> >>>>>>>>>>>> >>> > spool >>> >>>> >>> >>>>>>>>>>>> >>> > would >>> >>>> >>> >>>>>>>>>>>> >>> > take more space. >>> >>>> >>> >>>>>>>>>>>> >>> > The >>> >>>> >>> >>>>>>>>>>>> >>> > brackets I posted look like they could be >>> >>>> >>> >>>>>>>>>>>> >>> > attached to >>> >>>> >>> >>>>>>>>>>>> >>> > the >>> >>>> >>> >>>>>>>>>>>> >>> > back of >>> >>>> >>> >>>>>>>>>>>> >>> > printer. >>> >>>> >>> >>>>>>>>>>>> >>> > >>> >>>> >>> >>>>>>>>>>>> >>> > On 2013-09-24 11:32 AM, "d-_-b" >>> >>>> >>> >>>>>>>>>>>> >>> > <thor.robin...@gmail.com> >>> >>>> >>> >>>>>>>>>>>> >>> > wrote: >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> http://www.thingiverse.com/thing:52927 <- >>> >>>> >>> >>>>>>>>>>>> >>> >> another >>> >>>> >>> >>>>>>>>>>>> >>> >> option >>> >>>> >>> >>>>>>>>>>>> >>> >> for the >>> >>>> >>> >>>>>>>>>>>> >>> >> spool >>> >>>> >>> >>>>>>>>>>>> >>> >> holder >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> On Mon, Sep 23, 2013 at 12:28 PM, Stefan H.A >>> >>>> >>> >>>>>>>>>>>> >>> >> <stefan...@gmail.com> >>> >>>> >>> >>>>>>>>>>>> >>> >> wrote: >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> Some interesting and helpful links I found >>> >>>> >>> >>>>>>>>>>>> >>> >>> surfing >>> >>>> >>> >>>>>>>>>>>> >>> >>> thingiverse and >>> >>>> >>> >>>>>>>>>>>> >>> >>> the >>> >>>> >>> >>>>>>>>>>>> >>> >>> reprap wiki. >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> This might work for a spool holder. >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> http://www.thingiverse.com/thing:63431 >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> Some info about abs and pla. Note the >>> >>>> >>> >>>>>>>>>>>> >>> >>> suggestions >>> >>>> >>> >>>>>>>>>>>> >>> >>> regarding print >>> >>>> >>> >>>>>>>>>>>> >>> >>> surface. >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> http://reprap.org/wiki/ABS >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> http://reprap.org/wiki/PLA >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> Marlin firmware's home page which includes >>> >>>> >>> >>>>>>>>>>>> >>> >>> a >>> >>>> >>> >>>>>>>>>>>> >>> >>> list of >>> >>>> >>> >>>>>>>>>>>> >>> >>> implimented G >>> >>>> >>> >>>>>>>>>>>> >>> >>> and M >>> >>>> >>> >>>>>>>>>>>> >>> >>> codes. >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> https://github.com/ErikZalm/Marlin >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> On 2013-08-28 1:00 PM, "Aemilianus Kehler" >>> >>>> >>> >>>>>>>>>>>> >>> >>> <zew...@gmail.com> wrote: >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> Stupid huffer, why don't you learn to >>> >>>> >>> >>>>>>>>>>>> >>> >>>> share? >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> Cheers!! >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> On Aug 27, 2013, at 5:04 PM, Justin Lacko >>> >>>> >>> >>>>>>>>>>>> >>> >>>> <jus...@takaji.ca> wrote: >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> Of course I huffed it all! How else could >>> >>>> >>> >>>>>>>>>>>> >>> >>>> I >>> >>>> >>> >>>>>>>>>>>> >>> >>>> say I'm >>> >>>> >>> >>>>>>>>>>>> >>> >>>> on >>> >>>> >>> >>>>>>>>>>>> >>> >>>> such a long >>> >>>> >>> >>>>>>>>>>>> >>> >>>> "trip" to "Denmark"? >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> On 27 August 2013 23:59, Jim MacKenzie >>> >>>> >>> >>>>>>>>>>>> >>> >>>> <protoj...@gmail.com> wrote: >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> He probably huffed it all. >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> On Aug 27, 2013 4:58 PM, "Roswyne" >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> <rosw...@gmail.com> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> wrote: >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> Justin had a 1L tin of it, IIRC. I doubt >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> he >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> took >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> it >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> to Denmark! >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> On Aug 27, 2013 4:26 PM, "Stefan H.A" >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> <stefan...@gmail.com> wrote: >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> I am thinking it might be good to have >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> one >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> thread >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> for all things >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> 3d >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> printer so I am starting one. >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> FYI - I won't be able to make it to the >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> space >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> until >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> sometime >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> after >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> the meeting, not sure when though. My >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> cousin is >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> visiting from >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> Iceland and >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> she is interested in seeing the 3d >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> printer >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> so >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> I'll >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> be bringing >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> her along. >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> Also I hope to pick up some nail polish >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> remover >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> (acetone) to >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> clean >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> the print bed and maybe checking out >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> the >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> heated >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> bed >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> as it has >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> been acting >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> up. >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> _______________________________________________ >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> Help: >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> Archive: >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> _______________________________________________ >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> Help: >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> Archive: >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> _______________________________________________ >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> Help: >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> Archive: >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> _______________________________________________ >>> >>>> >>> >>>>>>>>>>>> >>> >>>> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>>>>> >>> >>>> Help: >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>>>>> >>> >>>> Archive: >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> _______________________________________________ >>> >>>> >>> >>>>>>>>>>>> >>> >>>> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>>>>> >>> >>>> Help: >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>>>>> >>> >>>> Archive: >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> _______________________________________________ >>> >>>> >>> >>>>>>>>>>>> >>> >>> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>>>>> >>> >>> Help: >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>>>>> >>> >>> Archive: >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> -- >>> >>>> >>> >>>>>>>>>>>> >>> >> -- >>> >>>> >>> >>>>>>>>>>>> >>> >> ) thor.robinson; >>> >>>> >>> >>>>>>>>>>>> >>> >> ) icon/phreshlyspun/ppca/skullspace >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> -----BEGIN GEEK CODE BLOCK----- >>> >>>> >>> >>>>>>>>>>>> >>> >> Version: 3.12 >>> >>>> >>> >>>>>>>>>>>> >>> >> GMU/O/AT/! d- s+:+ a C++++ UL++++ P L+++@ >>> >>>> >>> >>>>>>>>>>>> >>> >> E---- >>> >>>> >>> >>>>>>>>>>>> >>> >> W@ N! >>> >>>> >>> >>>>>>>>>>>> >>> >> o >>> >>>> >>> >>>>>>>>>>>> >>> >> K? w--- >>> >>>> >>> >>>>>>>>>>>> >>> >> O- M-- V? PS+++ PEY+ PGP+ t+ 5+ X R tv++ >>> >>>> >>> >>>>>>>>>>>> >>> >> DI++ >>> >>>> >>> >>>>>>>>>>>> >>> >> D++ G+ >>> >>>> >>> >>>>>>>>>>>> >>> >> e* >>> >>>> >>> >>>>>>>>>>>> >>> >> h-- r y+ z+ >>> >>>> >>> >>>>>>>>>>>> >>> >> ------END GEEK CODE BLOCK------ >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> _______________________________________________ >>> >>>> >>> >>>>>>>>>>>> >>> >> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>>>>> >>> >> Help: >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>>>>> >>> >> Archive: >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> >>> >>>> >>> >>>>>>>>>>>> >>> >> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>>>>>> >>> > >>> >>>> >>> >>>>>>>>>>>> >>> > >>> >>>> >>> >>>>>>>>>>>> >>> > >>> >>>> >>> >>>>>>>>>>>> >>> > _______________________________________________ >>> >>>> >>> >>>>>>>>>>>> >>> > SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>>>>> >>> > Help: >>> >>>> >>> >>>>>>>>>>>> >>> > >>> >>>> >>> >>>>>>>>>>>> >>> > >>> >>>> >>> >>>>>>>>>>>> >>> > >>> >>>> >>> >>>>>>>>>>>> >>> > http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>>>>> >>> > Archive: >>> >>>> >>> >>>>>>>>>>>> >>> > >>> >>>> >>> >>>>>>>>>>>> >>> > >>> >>>> >>> >>>>>>>>>>>> >>> > >>> >>>> >>> >>>>>>>>>>>> >>> > https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>>>>>> >>> _______________________________________________ >>> >>>> >>> >>>>>>>>>>>> >>> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>>>>> >>> Help: >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>>>>> >>> Archive: >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> >>> >>>> >>> >>>>>>>>>>>> >>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> _______________________________________________ >>> >>>> >>> >>>>>>>>>>>> >> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>>>>> >> Help: >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>>>>> >> Archive: >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> >>> >>>> >>> >>>>>>>>>>>> >> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>>>>>> > >>> >>>> >>> >>>>>>>>>>>> > >>> >>>> >>> >>>>>>>>>>>> > _______________________________________________ >>> >>>> >>> >>>>>>>>>>>> > SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>>>>> > Help: >>> >>>> >>> >>>>>>>>>>>> > >>> >>>> >>> >>>>>>>>>>>> > >>> >>>> >>> >>>>>>>>>>>> > >>> >>>> >>> >>>>>>>>>>>> > http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>>>>> > Archive: >>> >>>> >>> >>>>>>>>>>>> > >>> >>>> >>> >>>>>>>>>>>> > >>> >>>> >>> >>>>>>>>>>>> > >>> >>>> >>> >>>>>>>>>>>> > https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>>>>>> _______________________________________________ >>> >>>> >>> >>>>>>>>>>>> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>>>>> Help: >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>>>>> Archive: >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>>>>>>>>>> >>> >>>> >>> >>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>>>> >>> >>>> >>> >>>>>>>>>> >>> >>>> >>> >>>>>>>>>> _______________________________________________ >>> >>>> >>> >>>>>>>>>> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>>> Help: >>> >>>> >>> >>>>>>>>>> >>> >>>> >>> >>>>>>>>>> >>> >>>> >>> >>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>>> Archive: >>> >>>> >>> >>>>>>>>>> >>> >>>> >>> >>>>>>>>>> >>> >>>> >>> >>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>>> >>> >>>> >>> >>>>>>>>> >>> >>>> >>> >>>>>>>>> >>> >>>> >>> >>>>>>>>> >>> >>>> >>> >>>>>>>>> -- >>> >>>> >>> >>>>>>>>> -- >>> >>>> >>> >>>>>>>>> ) thor.robinson; >>> >>>> >>> >>>>>>>>> ) icon/phreshlyspun/ppca/skullspace >>> >>>> >>> >>>>>>>>> >>> >>>> >>> >>>>>>>>> -----BEGIN GEEK CODE BLOCK----- >>> >>>> >>> >>>>>>>>> Version: 3.12 >>> >>>> >>> >>>>>>>>> GMU/O/AT/! d- s+:+ a C++++ UL++++ P L+++@ E---- W@ N! >>> >>>> >>> >>>>>>>>> o K? >>> >>>> >>> >>>>>>>>> w--- >>> >>>> >>> >>>>>>>>> O- M-- V? PS+++ PEY+ PGP+ t+ 5+ X R tv++ DI++ D++ G+ >>> >>>> >>> >>>>>>>>> e* >>> >>>> >>> >>>>>>>>> h-- r >>> >>>> >>> >>>>>>>>> y+ z+ >>> >>>> >>> >>>>>>>>> ------END GEEK CODE BLOCK------ >>> >>>> >>> >>>>>>>>> >>> >>>> >>> >>>>>>>>> _______________________________________________ >>> >>>> >>> >>>>>>>>> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>>> Help: >>> >>>> >>> >>>>>>>>> >>> >>>> >>> >>>>>>>>> >>> >>>> >>> >>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>>> Archive: >>> >>>> >>> >>>>>>>>> >>> >>>> >>> >>>>>>>>> >>> >>>> >>> >>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>>> >>> >>>> >>> >>>>>>>> >>> >>>> >>> >>>>>>>> _______________________________________________ >>> >>>> >>> >>>>>>>> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>>> Help: >>> >>>> >>> >>>>>>>> >>> >>>> >>> >>>>>>>> >>> >>>> >>> >>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>>> Archive: >>> >>>> >>> >>>>>>>> >>> >>>> >>> >>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>>>>> >>> >>>> >>> >>>>>>> >>> >>>> >>> >>>>>>> >>> >>>> >>> >>>>>>> _______________________________________________ >>> >>>> >>> >>>>>>> SkullSpace Discuss Mailing List >>> >>>> >>> >>>>>>> Help: >>> >>>> >>> >>>>>>> >>> >>>> >>> >>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>>>>> Archive: >>> >>>> >>> >>>>>>> >>> >>>> >>> >>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>>> >>> >>>> >>> >>>> >>> >>>> >>> >>>> _______________________________________________ >>> >>>> >>> >>>> SkullSpace Discuss Mailing List >>> >>>> >>> >>>> Help: >>> >>>> >>> >>>> >>> >>>> >>> >>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>>> Archive: >>> >>>> >>> >>>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >>> >>> >>>> >>> >>> >>> >>>> >>> >>> >>> >>>> >>> >>> _______________________________________________ >>> >>>> >>> >>> SkullSpace Discuss Mailing List >>> >>>> >>> >>> Help: >>> >>>> >>> >>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >>> Archive: >>> >>>> >>> >>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> >> >>> >>>> >>> >> >>> >>>> >>> >> _______________________________________________ >>> >>>> >>> >> SkullSpace Discuss Mailing List >>> >>>> >>> >> Help: >>> >>>> >>> >> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> >> Archive: >>> >>>> >>> >> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> > >>> >>>> >>> > >>> >>>> >>> > >>> >>>> >>> > _______________________________________________ >>> >>>> >>> > SkullSpace Discuss Mailing List >>> >>>> >>> > Help: >>> >>>> >>> > http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> > Archive: >>> >>>> >>> > https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >>> _______________________________________________ >>> >>>> >>> SkullSpace Discuss Mailing List >>> >>>> >>> Help: >>> >>>> >>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >>> Archive: >>> >>>> >>> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> >> >>> >>>> >> >>> >>>> >> >>> >>>> >> _______________________________________________ >>> >>>> >> SkullSpace Discuss Mailing List >>> >>>> >> Help: >>> >>>> >> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> >> Archive: >>> >>>> >> https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> > >>> >>>> > >>> >>>> > _______________________________________________ >>> >>>> > SkullSpace Discuss Mailing List >>> >>>> > Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> > Archive: >>> >>>> > https://groups.google.com/group/skullspace-discuss-archive/ >>> >>>> _______________________________________________ >>> >>>> SkullSpace Discuss Mailing List >>> >>>> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>>> Archive: https://groups.google.com/group/skullspace-discuss-archive/ >>> >>> >>> >>> >>> >>> _______________________________________________ >>> >>> SkullSpace Discuss Mailing List >>> >>> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> >>> Archive: https://groups.google.com/group/skullspace-discuss-archive/ >>> >> >>> >> >>> > >>> > >>> > _______________________________________________ >>> > SkullSpace Discuss Mailing List >>> > Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> > Archive: https://groups.google.com/group/skullspace-discuss-archive/ >>> _______________________________________________ >>> SkullSpace Discuss Mailing List >>> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> Archive: https://groups.google.com/group/skullspace-discuss-archive/ >> >> >> _______________________________________________ >> SkullSpace Discuss Mailing List >> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >> Archive: https://groups.google.com/group/skullspace-discuss-archive/ > > > > _______________________________________________ > SkullSpace Discuss Mailing List > Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss > Archive: https://groups.google.com/group/skullspace-discuss-archive/ _______________________________________________ SkullSpace Discuss Mailing List Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss Archive: https://groups.google.com/group/skullspace-discuss-archive/
