THat came out nice! Good job! Cheers!!
On Oct 4, 2013, at 1:49 AM, Jay Smith <jayvsm...@gmail.com> wrote: > I did a little test tonight on hot swapping between ABS colours, and > the results turned out pretty decently: > > https://pic.twitter.com/0ybanbLmKP > https://pic.twitter.com/61b6oqfnpJ > > Note: These instructions assume that the ABS types are similar enough > to have the same settings when generating gcode. The natural and black > seemed to work fine with the settings we've been using so far. > > 1) Print until you wish to change colours > 2) Immediately enter the following commands: PAUSE - Reverse 4mm > (approx) - Go up 40 units on the Z axis. The reverse is so you don't > spill over what you've printed already > 3) Replace the filament with your second colour > 4) extrude 20mm to make sure the new roll is loaded, using a pair of > needle-nose pliers to keep anything from dripping onto your model. > 5) resume the print > 6) There is no step 6 > > WARNING: Never return the head to home while the printer is paused! > When the print resumes, it reverses every action you performed to get > back into position. What's the reverse of going to Z-Home? Burrowing > down into the center of the earth, that's what. > > I had the print head crash into the bed today on account of the issue > above - thankfully I had one hand on the kill switch. I re-taped and > leveled the bed before printing again, it looks to be in perfect > working order. Re-taping was probably overkill, but I figured it was > time to clean it up a bit. > > - Jay / @Sporked > > On Wed, Oct 2, 2013 at 12:25 PM, Brian Kulyk <br...@kulyk.ca> wrote: >> I just ordered us some more natural abs. >> >> >> Brian Kulyk >> 204.887.6988 >> >> >> On Wed, Oct 2, 2013 at 8:21 AM, Stefan H.A <stefan...@gmail.com> wrote: >>> >>> We left it mounted to the top to avoid having to update the firmware. >>> >>> On 2013-10-02 8:16 AM, "Benjamin Bergman" <b...@benbergman.ca> wrote: >>>> >>>> Thanks a lot, guys! Just curious, is the switch still mounted at the >>>> top, or did you try mounting the new switch at the bottom? >>>> >>>> On Tue, Oct 1, 2013 at 11:18 PM, Brian Kulyk <br...@kulyk.ca> wrote: >>>>> Thanks to the amazing help from Stephan, Dr. West, Aemilianus and Thor >>>>> we >>>>> managed to get the new mechanical switch in place and homing properly. >>>>> It >>>>> looks to be working great and people should be able to use the printer >>>>> again, but it looks like the print bed will require some additional >>>>> leveling. Small parts in the center of the bed should be fine, but you >>>>> may >>>>> experience warping in larger parts. >>>>> >>>>> Thanks again to everyone who has helped get the printer running again! >>>>> Amazing team work. >>>>> >>>>> >>>>> Brian Kulyk >>>>> 204.887.6988 >>>>> >>>>> >>>>> On Tue, Oct 1, 2013 at 3:47 PM, Brian Kulyk <br...@kulyk.ca> wrote: >>>>>> >>>>>> I bought one this afternoon, I will bring it to the meeting today. >>>>>> >>>>>> >>>>>> Brian Kulyk >>>>>> 204.887.6988 >>>>>> >>>>>> >>>>>> On Tue, Oct 1, 2013 at 2:45 PM, Stefan H.A <stefan...@gmail.com> >>>>>> wrote: >>>>>>> >>>>>>> I believe there are some at the space(can anyone confirm). If not I >>>>>>> have >>>>>>> some at home. I can stop there and grab a couple on my way to the >>>>>>> meeting. >>>>>>> >>>>>>> On 2013-10-01 2:33 PM, "Benjamin Bergman" <b...@benbergman.ca> wrote: >>>>>>>> >>>>>>>> Ya, I think my vote is for the microswitch as well, but I'll toss a >>>>>>>> couple hall effect sensors in with my order so we can fix up the >>>>>>>> other >>>>>>>> board in case we want to use it again. Do we have extra >>>>>>>> microswitches, >>>>>>>> or should I grab a few of those too? >>>>>>>> >>>>>>>> On Tue, Oct 1, 2013 at 2:06 PM, Stefan H.A <stefan...@gmail.com> >>>>>>>> wrote: >>>>>>>>> Yeah, I think a micro switch (as picture in the link in the IRC >>>>>>>>> conversation) will work fine. We could use an opto-interupter ( >>>>>>>>> >>>>>>>>> >>>>>>>>> http://www.jameco.com/1/1/25649-h21a1-opto-electronic-interrupter-switch-transistor-sensors.html >>>>>>>>> ) if we want to get fancy but I think a microswitch will work just >>>>>>>>> as >>>>>>>>> well. >>>>>>>>> >>>>>>>>> On 2013-10-01 1:48 PM, "Brian Kulyk" <br...@kulyk.ca> wrote: >>>>>>>>>> >>>>>>>>>> I was looking on Digikey for the sensor we need and noticed many >>>>>>>>>> different >>>>>>>>>> versions so I decided to contact Maker's Tool Works to find out >>>>>>>>>> the >>>>>>>>>> specifics of the sensor they used. They (as well as the folks on >>>>>>>>>> IRC) >>>>>>>>>> suggest using a mechanical switch. Eventually I found that this >>>>>>>>>> is >>>>>>>>>> the >>>>>>>>>> part we need if we want to continue using the hall effect sensor. >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> http://www.digikey.ca/product-detail/en/TLE4905L%20E6433/TLE4905LE6433INCT-ND/1650234 >>>>>>>>>> >>>>>>>>>> If we decide to order these we should get a few backups. Ben, >>>>>>>>>> it's >>>>>>>>>> not >>>>>>>>>> too late to combine with your order that would be great. I can >>>>>>>>>> give >>>>>>>>>> you >>>>>>>>>> some cash for the order tonight at the meeting. >>>>>>>>>> >>>>>>>>>> ME: >>>>>>>>>> >>>>>>>>>>> >>>>>>>>>>> I have broken the sensor off of the "Cheep O" board. I would >>>>>>>>>>> order >>>>>>>>>>> another one from you, but the store appears to be about can I >>>>>>>>>>> please >>>>>>>>>>> get >>>>>>>>>>> some additional information about the sensor so I can order a >>>>>>>>>>> replacement >>>>>>>>>>> elsewhere. >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> Maker's Tool Works >>>>>>>>>> >>>>>>>>>>> Unfortunately we are not expecting to have them back in stock >>>>>>>>>>> for >>>>>>>>>>> quiet a >>>>>>>>>>> while. You're kit should have another mechanical endstop. All >>>>>>>>>>> current kits >>>>>>>>>>> do not have a cheap-o and we are finding the mechanical just as >>>>>>>>>>> effective. >>>>>>>>>>> The Cheap-o hall endsop is designed by BLDDK, I have seen one >>>>>>>>>>> clone >>>>>>>>>>> online >>>>>>>>>>> and some diy versions on thingiverse. >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> I found that I can order a replacement board from here: >>>>>>>>>> http://www.elecfreaks.com/store/hall-endstop-p-654.html Though >>>>>>>>>> it >>>>>>>>>> does look >>>>>>>>>> a little different they are both based off the BLDDK's design. >>>>>>>>>> >>>>>>>>>> Chat log from IRC: >>>>>>>>>> >>>>>>>>>>>> [11:48] <grumpy> I broke the sensor off of my cheap-o hall z >>>>>>>>>>>> endstop. >>>>>>>>>>>> Can anybody tell me where I can order a replacement (the >>>>>>>>>>>> official >>>>>>>>>>>> store is >>>>>>>>>>>> sold out). >>>>>>>>>>>> >>>>>>>>>>>> [11:48] <skywurz> grumpy i too did that >>>>>>>>>>>> >>>>>>>>>>>> [11:48] <skywurz> grumpy i dont like that sensor >>>>>>>>>>>> >>>>>>>>>>>> [11:49] <grumpy> skywurz what are you using now? >>>>>>>>>>>> >>>>>>>>>>>> [11:49] <skywurz> grumpy may i recommend >>>>>>>>>>>> http://www.wuala.com/skywurz/Public/IMG_20130519_122911.jpg/ >>>>>>>>>>>> >>>>>>>>>>>> [11:51] <grumpy> skywurz I was thinking of going with something >>>>>>>>>>>> like >>>>>>>>>>>> that, but others were worried that it might not be as accurate >>>>>>>>>>>> as >>>>>>>>>>>> the >>>>>>>>>>>> hall-effect thing, I take you are not having any troubles with >>>>>>>>>>>> your >>>>>>>>>>>> replacement? >>>>>>>>>>>> >>>>>>>>>>>> [11:51] <skywurz> grumpy it really does not make that much of a >>>>>>>>>>>> difference >>>>>>>>>>>> >>>>>>>>>>>> [11:52] <skywurz> think about how far off you could have thrown >>>>>>>>>>>> that >>>>>>>>>>>> cheap-o off by bumping the sensor >>>>>>>>>>>> >>>>>>>>>>>> [11:54] <grumpy> skywurz Sounds good I will give it shot. I >>>>>>>>>>>> already >>>>>>>>>>>> printed off a bracket to use a switch like that anyway. >>>>>>>>>>>> >>>>>>>>>>>> [11:54] <skywurz> never answered my imagineer question >>>>>>>>>>>> >>>>>>>>>>>> [11:54] <skywurz> grumpy sweet >>>>>>>>>>>> >>>>>>>>>>>> [11:54] <skywurz> grumpy if you have no interest in saving the >>>>>>>>>>>> old >>>>>>>>>>>> cheap >>>>>>>>>>>> o you can re use the wires on it >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> Brian Kulyk >>>>>>>>>> 204.887.6988 >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> On Sat, Sep 28, 2013 at 7:11 PM, Benjamin Bergman >>>>>>>>>> <b...@benbergman.ca> >>>>>>>>>> wrote: >>>>>>>>>>> >>>>>>>>>>> I just took a look at the sensor and I doubt it can be >>>>>>>>>>> resoldered. I >>>>>>>>>>> was about to get some stuff from digikey, so we can toss a few >>>>>>>>>>> sensors >>>>>>>>>>> into that order as well. Shipping isn't much and it arrives >>>>>>>>>>> fast. >>>>>>>>>>> I'm >>>>>>>>>>> just not sure when our order is going out (should be this week >>>>>>>>>>> though). >>>>>>>>>>> >>>>>>>>>>> On Sat, Sep 28, 2013 at 3:38 PM, Brian Kulyk <br...@kulyk.ca> >>>>>>>>>>> wrote: >>>>>>>>>>>> I just broke off the board, one of the leads is now really >>>>>>>>>>>> small. >>>>>>>>>>>> Someone >>>>>>>>>>>> might be able to solder it back together, but it's beyond my >>>>>>>>>>>> skill >>>>>>>>>>>> level. >>>>>>>>>>>> >>>>>>>>>>>> I found a mount for a physical switch on thingiverse, we could >>>>>>>>>>>> try >>>>>>>>>>>> that >>>>>>>>>>>> until the new sensor gets here or until someone with more >>>>>>>>>>>> skill >>>>>>>>>>>> than I >>>>>>>>>>>> can >>>>>>>>>>>> re-solder the old one. >>>>>>>>>>>> >>>>>>>>>>>> >>>>>>>>>>>> >>>>>>>>>>>> >>>>>>>>>>>> Brian Kulyk >>>>>>>>>>>> 204.887.6988 >>>>>>>>>>>> >>>>>>>>>>>> >>>>>>>>>>>> On Sat, Sep 28, 2013 at 3:19 PM, Stefan H.A >>>>>>>>>>>> <stefan...@gmail.com> >>>>>>>>>>>> wrote: >>>>>>>>>>>>> >>>>>>>>>>>>> Yeah that will likely work. I've been looking for a schematic >>>>>>>>>>>>> for >>>>>>>>>>>>> that >>>>>>>>>>>>> board to ensure the hall effect sensor is the same as the one >>>>>>>>>>>>> sold at >>>>>>>>>>>>> sparkfun but can't seem to find it using my phone though. >>>>>>>>>>>>> Odds >>>>>>>>>>>>> are >>>>>>>>>>>>> very good >>>>>>>>>>>>> they are equivalent. >>>>>>>>>>>>> >>>>>>>>>>>>> Did the actual sensor break or did it just break off the >>>>>>>>>>>>> board. >>>>>>>>>>>>> If it >>>>>>>>>>>>> just >>>>>>>>>>>>> broke off the board maybe we can reattach it. >>>>>>>>>>>>> >>>>>>>>>>>>> On 2013-09-28 2:19 PM, "Brian Kulyk" <br...@kulyk.ca> wrote: >>>>>>>>>>>>>> >>>>>>>>>>>>>> Unfortunately maker stool works is out of the "Cheap-O Hall >>>>>>>>>>>>>> Endstop >>>>>>>>>>>>>> Sensor". Perhaps I can just order a new sensor from >>>>>>>>>>>>>> sparkfun >>>>>>>>>>>>>> and >>>>>>>>>>>>>> solder it >>>>>>>>>>>>>> onto the existing board. >>>>>>>>>>>>>> >>>>>>>>>>>>>> Thoughts? >>>>>>>>>>>>>> >>>>>>>>>>>>>> >>>>>>>>>>>>>> Brian Kulyk >>>>>>>>>>>>>> 204.887.6988 >>>>>>>>>>>>>> >>>>>>>>>>>>>> >>>>>>>>>>>>>> On Sat, Sep 28, 2013 at 2:07 PM, Stefan H.A >>>>>>>>>>>>>> <stefan...@gmail.com> >>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>> >>>>>>>>>>>>>>> If we are ordering something from makerstoolworks.com maybe >>>>>>>>>>>>>>> we >>>>>>>>>>>>>>> should >>>>>>>>>>>>>>> see if anything changed from the beta kit we got and have >>>>>>>>>>>>>>> that >>>>>>>>>>>>>>> included in >>>>>>>>>>>>>>> the shipment. Also I think there were some parts that were >>>>>>>>>>>>>>> not >>>>>>>>>>>>>>> right >>>>>>>>>>>>>>> in the >>>>>>>>>>>>>>> original kit we might like to get replaced. >>>>>>>>>>>>>>> >>>>>>>>>>>>>>> On 2013-09-28 1:37 PM, "Stefan H.A" <stefan...@gmail.com> >>>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>> If you are going to use the 'peice of paper' method you >>>>>>>>>>>>>>>> need >>>>>>>>>>>>>>>> to >>>>>>>>>>>>>>>> remove >>>>>>>>>>>>>>>> homing lines from custom gcode section of the slicer >>>>>>>>>>>>>>>> config. I >>>>>>>>>>>>>>>> beleive the >>>>>>>>>>>>>>>> appropriate lines are g28 and g92 z183. >>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>> On 2013-09-28 1:30 PM, "Stefan H.A" <stefan...@gmail.com> >>>>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>> We got the end stop with the kit. A replacement should be >>>>>>>>>>>>>>>>> available >>>>>>>>>>>>>>>>> from makerstoolworks.com. A microswitch could also be >>>>>>>>>>>>>>>>> used if >>>>>>>>>>>>>>>>> we >>>>>>>>>>>>>>>>> can figure >>>>>>>>>>>>>>>>> a way to attach it. In the mean time we can still use the >>>>>>>>>>>>>>>>> "piece >>>>>>>>>>>>>>>>> of paper" >>>>>>>>>>>>>>>>> method of zeroing. If you need a refresher check old >>>>>>>>>>>>>>>>> revisions of >>>>>>>>>>>>>>>>> the wiki. >>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>> This should not have happened. Is it possible the endstop >>>>>>>>>>>>>>>>> came >>>>>>>>>>>>>>>>> disconnected? I suppose the firmware could have gone >>>>>>>>>>>>>>>>> insane >>>>>>>>>>>>>>>>> when >>>>>>>>>>>>>>>>> it froze up >>>>>>>>>>>>>>>>> and that is why it didn't obey the endstop. In the >>>>>>>>>>>>>>>>> future, we >>>>>>>>>>>>>>>>> should >>>>>>>>>>>>>>>>> probably completely power down and disconnect the usb >>>>>>>>>>>>>>>>> cable >>>>>>>>>>>>>>>>> when >>>>>>>>>>>>>>>>> recovering >>>>>>>>>>>>>>>>> from a crash to ensure the firmware gets reset. This now >>>>>>>>>>>>>>>>> makes me >>>>>>>>>>>>>>>>> wonder if >>>>>>>>>>>>>>>>> the freezing problem is caused by the firmware and not >>>>>>>>>>>>>>>>> the >>>>>>>>>>>>>>>>> computer. Maybe >>>>>>>>>>>>>>>>> we should see if any other user are reporting this and >>>>>>>>>>>>>>>>> check >>>>>>>>>>>>>>>>> if >>>>>>>>>>>>>>>>> there is a >>>>>>>>>>>>>>>>> more recent version of the Marlin firmware. >>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>> On 2013-09-28 1:05 PM, "Brian Kulyk" <br...@kulyk.ca> >>>>>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>> Somehow I managed to break the z axis end-stop sensor. >>>>>>>>>>>>>>>>>> I >>>>>>>>>>>>>>>>>> was >>>>>>>>>>>>>>>>>> printing this morning, and the print failed. I hit the >>>>>>>>>>>>>>>>>> button to >>>>>>>>>>>>>>>>>> disconnect, and reconnected to the printer then hit the >>>>>>>>>>>>>>>>>> z >>>>>>>>>>>>>>>>>> home >>>>>>>>>>>>>>>>>> button so I >>>>>>>>>>>>>>>>>> could remove the failed print. The z axis did NOT stop >>>>>>>>>>>>>>>>>> at 0, >>>>>>>>>>>>>>>>>> it >>>>>>>>>>>>>>>>>> kept going >>>>>>>>>>>>>>>>>> and broke a little black piece off of the z end-stop >>>>>>>>>>>>>>>>>> sensor. >>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>> If someone can tell me where we got the sensor from I >>>>>>>>>>>>>>>>>> can go >>>>>>>>>>>>>>>>>> and >>>>>>>>>>>>>>>>>> get >>>>>>>>>>>>>>>>>> or order us another one as soon as possible. >>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>> Sorry for the inconvenience. >>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>> Brian Kulyk >>>>>>>>>>>>>>>>>> 204.887.6988 >>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>> On Fri, Sep 27, 2013 at 4:33 PM, Stefan H.A >>>>>>>>>>>>>>>>>> <stefan...@gmail.com> >>>>>>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>> Yeah, I think slowing down more and using the fan >>>>>>>>>>>>>>>>>>> less(read: >>>>>>>>>>>>>>>>>>> almost >>>>>>>>>>>>>>>>>>> never) is the solution to the cracks we are getting in >>>>>>>>>>>>>>>>>>> some >>>>>>>>>>>>>>>>>>> parts. >>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>> On 2013-09-27 3:12 PM, "d-_-b" >>>>>>>>>>>>>>>>>>> <thor.robin...@gmail.com> >>>>>>>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>> Parts with fine detail can be run with a lower minimum >>>>>>>>>>>>>>>>>>>> speed ( >>>>>>>>>>>>>>>>>>>> default 10mm/s ). we ran the second triforce at 1mm/s >>>>>>>>>>>>>>>>>>>> minimum >>>>>>>>>>>>>>>>>>>> speed and that >>>>>>>>>>>>>>>>>>>> was a tad low, but gave us excellent detail. >>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>> On Fri, Sep 27, 2013 at 10:36 AM, Stefan H.A >>>>>>>>>>>>>>>>>>>> <stefan...@gmail.com> >>>>>>>>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>> I've added some useful links to the tuning section of >>>>>>>>>>>>>>>>>>>>> 3d >>>>>>>>>>>>>>>>>>>>> printer >>>>>>>>>>>>>>>>>>>>> wiki page. >>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>> Based on the 'too cold' section of the trouble >>>>>>>>>>>>>>>>>>>>> shooting >>>>>>>>>>>>>>>>>>>>> guide >>>>>>>>>>>>>>>>>>>>> I >>>>>>>>>>>>>>>>>>>>> beleive we are cooling the part too much with the >>>>>>>>>>>>>>>>>>>>> fan. I >>>>>>>>>>>>>>>>>>>>> think >>>>>>>>>>>>>>>>>>>>> that when >>>>>>>>>>>>>>>>>>>>> printing with ABS the fan should remain off unless >>>>>>>>>>>>>>>>>>>>> absolutely >>>>>>>>>>>>>>>>>>>>> necessary (ie. >>>>>>>>>>>>>>>>>>>>> Very short layers). Thinking back to the triforce, it >>>>>>>>>>>>>>>>>>>>> only had >>>>>>>>>>>>>>>>>>>>> trouble at >>>>>>>>>>>>>>>>>>>>> the very top where the layers were taking only few >>>>>>>>>>>>>>>>>>>>> seconds. >>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>> On 2013-09-26 12:14 AM, "Stefan H.A" >>>>>>>>>>>>>>>>>>>>> <stefan...@gmail.com> >>>>>>>>>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>> Be advised, I changed the infill patern to >>>>>>>>>>>>>>>>>>>>>> honeycomb. >>>>>>>>>>>>>>>>>>>>>> Don't >>>>>>>>>>>>>>>>>>>>>> be >>>>>>>>>>>>>>>>>>>>>> alarmed if the printer appears to have a convulsion >>>>>>>>>>>>>>>>>>>>>> while >>>>>>>>>>>>>>>>>>>>>> printing infill. >>>>>>>>>>>>>>>>>>>>>> Do keep an eye out for screws coming loose. >>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>> I've also set it to print a solid layer every 40 >>>>>>>>>>>>>>>>>>>>>> layers. >>>>>>>>>>>>>>>>>>>>>> These >>>>>>>>>>>>>>>>>>>>>> settings should increase part strength considerably. >>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>> On 2013-09-24 3:39 PM, "Benjamin Bergman" >>>>>>>>>>>>>>>>>>>>>> <b...@benbergman.ca> >>>>>>>>>>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>> The second one I linked >>>>>>>>>>>>>>>>>>>>>>> (http://www.thingiverse.com/thing:124533) is >>>>>>>>>>>>>>>>>>>>>>> basically a proper version of the one that I >>>>>>>>>>>>>>>>>>>>>>> cobbled >>>>>>>>>>>>>>>>>>>>>>> together >>>>>>>>>>>>>>>>>>>>>>> months >>>>>>>>>>>>>>>>>>>>>>> ago that we are currently using. No disassembly >>>>>>>>>>>>>>>>>>>>>>> required to >>>>>>>>>>>>>>>>>>>>>>> install >>>>>>>>>>>>>>>>>>>>>>> that one. >>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>> It would have been nice if all their end plates had >>>>>>>>>>>>>>>>>>>>>>> cutouts >>>>>>>>>>>>>>>>>>>>>>> for >>>>>>>>>>>>>>>>>>>>>>> t-nuts >>>>>>>>>>>>>>>>>>>>>>> to be inserted, like the main back plate has. It >>>>>>>>>>>>>>>>>>>>>>> would >>>>>>>>>>>>>>>>>>>>>>> make >>>>>>>>>>>>>>>>>>>>>>> upgrading >>>>>>>>>>>>>>>>>>>>>>> things way easier. >>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>> On Tue, Sep 24, 2013 at 3:18 PM, Stefan H.A >>>>>>>>>>>>>>>>>>>>>>> <stefan...@gmail.com> wrote: >>>>>>>>>>>>>>>>>>>>>>>> Depending where the bracket attaches, the printer >>>>>>>>>>>>>>>>>>>>>>>> may >>>>>>>>>>>>>>>>>>>>>>>> need >>>>>>>>>>>>>>>>>>>>>>>> to >>>>>>>>>>>>>>>>>>>>>>>> be partially >>>>>>>>>>>>>>>>>>>>>>>> disassembled to add the t-nuts into the channels >>>>>>>>>>>>>>>>>>>>>>>> (looks >>>>>>>>>>>>>>>>>>>>>>>> like >>>>>>>>>>>>>>>>>>>>>>>> that may be the >>>>>>>>>>>>>>>>>>>>>>>> case for the top most screw). I have been looking >>>>>>>>>>>>>>>>>>>>>>>> for >>>>>>>>>>>>>>>>>>>>>>>> a >>>>>>>>>>>>>>>>>>>>>>>> solution that only >>>>>>>>>>>>>>>>>>>>>>>> needs t-nuts in accessable channels. >>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>> On 2013-09-24 3:09 PM, "Brian Kulyk" >>>>>>>>>>>>>>>>>>>>>>>> <br...@kulyk.ca> >>>>>>>>>>>>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> I like the first one Ben suggested >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> (http://www.thingiverse.com/thing:77301/#remixes) >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> Brian Kulyk >>>>>>>>>>>>>>>>>>>>>>>>> 204.887.6988 >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> On Tue, Sep 24, 2013 at 1:50 PM, Benjamin >>>>>>>>>>>>>>>>>>>>>>>>> Bergman >>>>>>>>>>>>>>>>>>>>>>>>> <b...@benbergman.ca> >>>>>>>>>>>>>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>> A few more options (all designed to attach to >>>>>>>>>>>>>>>>>>>>>>>>>> the >>>>>>>>>>>>>>>>>>>>>>>>>> MendelMax >>>>>>>>>>>>>>>>>>>>>>>>>> 2.0): >>>>>>>>>>>>>>>>>>>>>>>>>> http://www.thingiverse.com/thing:77301/#remixes >>>>>>>>>>>>>>>>>>>>>>>>>> http://www.thingiverse.com/thing:124533 >>>>>>>>>>>>>>>>>>>>>>>>>> http://www.thingiverse.com/thing:78741 >>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>> On Tue, Sep 24, 2013 at 12:33 PM, Stefan H.A >>>>>>>>>>>>>>>>>>>>>>>>>> <stefan...@gmail.com> wrote: >>>>>>>>>>>>>>>>>>>>>>>>>>> This would probably work but a stand alone >>>>>>>>>>>>>>>>>>>>>>>>>>> spool >>>>>>>>>>>>>>>>>>>>>>>>>>> would >>>>>>>>>>>>>>>>>>>>>>>>>>> take more space. >>>>>>>>>>>>>>>>>>>>>>>>>>> The >>>>>>>>>>>>>>>>>>>>>>>>>>> brackets I posted look like they could be >>>>>>>>>>>>>>>>>>>>>>>>>>> attached to >>>>>>>>>>>>>>>>>>>>>>>>>>> the >>>>>>>>>>>>>>>>>>>>>>>>>>> back of >>>>>>>>>>>>>>>>>>>>>>>>>>> printer. >>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>> On 2013-09-24 11:32 AM, "d-_-b" >>>>>>>>>>>>>>>>>>>>>>>>>>> <thor.robin...@gmail.com> >>>>>>>>>>>>>>>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> http://www.thingiverse.com/thing:52927 <- >>>>>>>>>>>>>>>>>>>>>>>>>>>> another >>>>>>>>>>>>>>>>>>>>>>>>>>>> option >>>>>>>>>>>>>>>>>>>>>>>>>>>> for the >>>>>>>>>>>>>>>>>>>>>>>>>>>> spool >>>>>>>>>>>>>>>>>>>>>>>>>>>> holder >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> On Mon, Sep 23, 2013 at 12:28 PM, Stefan H.A >>>>>>>>>>>>>>>>>>>>>>>>>>>> <stefan...@gmail.com> >>>>>>>>>>>>>>>>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> Some interesting and helpful links I found >>>>>>>>>>>>>>>>>>>>>>>>>>>>> surfing >>>>>>>>>>>>>>>>>>>>>>>>>>>>> thingiverse and >>>>>>>>>>>>>>>>>>>>>>>>>>>>> the >>>>>>>>>>>>>>>>>>>>>>>>>>>>> reprap wiki. >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> This might work for a spool holder. >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> http://www.thingiverse.com/thing:63431 >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> Some info about abs and pla. Note the >>>>>>>>>>>>>>>>>>>>>>>>>>>>> suggestions >>>>>>>>>>>>>>>>>>>>>>>>>>>>> regarding print >>>>>>>>>>>>>>>>>>>>>>>>>>>>> surface. >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> http://reprap.org/wiki/ABS >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> http://reprap.org/wiki/PLA >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> Marlin firmware's home page which includes >>>>>>>>>>>>>>>>>>>>>>>>>>>>> a >>>>>>>>>>>>>>>>>>>>>>>>>>>>> list of >>>>>>>>>>>>>>>>>>>>>>>>>>>>> implimented G >>>>>>>>>>>>>>>>>>>>>>>>>>>>> and M >>>>>>>>>>>>>>>>>>>>>>>>>>>>> codes. >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> https://github.com/ErikZalm/Marlin >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> On 2013-08-28 1:00 PM, "Aemilianus Kehler" >>>>>>>>>>>>>>>>>>>>>>>>>>>>> <zew...@gmail.com> wrote: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Stupid huffer, why don't you learn to >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> share? >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Cheers!! >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> On Aug 27, 2013, at 5:04 PM, Justin Lacko >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> <jus...@takaji.ca> wrote: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Of course I huffed it all! How else could >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> I >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> say I'm >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> on >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> such a long >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> "trip" to "Denmark"? >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> On 27 August 2013 23:59, Jim MacKenzie >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> <protoj...@gmail.com> wrote: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> He probably huffed it all. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> On Aug 27, 2013 4:58 PM, "Roswyne" >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> <rosw...@gmail.com> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> wrote: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Justin had a 1L tin of it, IIRC. I doubt >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> he >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> took >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> it >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> to Denmark! >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> On Aug 27, 2013 4:26 PM, "Stefan H.A" >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> <stefan...@gmail.com> wrote: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> I am thinking it might be good to have >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> one >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> thread >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> for all things >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> 3d >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> printer so I am starting one. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> FYI - I won't be able to make it to the >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> space >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> until >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> sometime >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> after >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> the meeting, not sure when though. My >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> cousin is >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> visiting from >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Iceland and >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> she is interested in seeing the 3d >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> printer >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> so >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> I'll >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> be bringing >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> her along. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Also I hope to pick up some nail polish >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> remover >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> (acetone) to >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> clean >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> the print bed and maybe checking out >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> the >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> heated >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> bed >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> as it has >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> been acting >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> up. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> -- >>>>>>>>>>>>>>>>>>>>>>>>>>>> -- >>>>>>>>>>>>>>>>>>>>>>>>>>>> ) thor.robinson; >>>>>>>>>>>>>>>>>>>>>>>>>>>> ) icon/phreshlyspun/ppca/skullspace >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> -----BEGIN GEEK CODE BLOCK----- >>>>>>>>>>>>>>>>>>>>>>>>>>>> Version: 3.12 >>>>>>>>>>>>>>>>>>>>>>>>>>>> GMU/O/AT/! d- s+:+ a C++++ UL++++ P L+++@ >>>>>>>>>>>>>>>>>>>>>>>>>>>> E---- >>>>>>>>>>>>>>>>>>>>>>>>>>>> W@ N! >>>>>>>>>>>>>>>>>>>>>>>>>>>> o >>>>>>>>>>>>>>>>>>>>>>>>>>>> K? w--- >>>>>>>>>>>>>>>>>>>>>>>>>>>> O- M-- V? PS+++ PEY+ PGP+ t+ 5+ X R tv++ >>>>>>>>>>>>>>>>>>>>>>>>>>>> DI++ >>>>>>>>>>>>>>>>>>>>>>>>>>>> D++ G+ >>>>>>>>>>>>>>>>>>>>>>>>>>>> e* >>>>>>>>>>>>>>>>>>>>>>>>>>>> h-- r y+ z+ >>>>>>>>>>>>>>>>>>>>>>>>>>>> ------END GEEK CODE BLOCK------ >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>> -- >>>>>>>>>>>>>>>>>>>> -- >>>>>>>>>>>>>>>>>>>> ) thor.robinson; >>>>>>>>>>>>>>>>>>>> ) icon/phreshlyspun/ppca/skullspace >>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>> -----BEGIN GEEK CODE BLOCK----- >>>>>>>>>>>>>>>>>>>> Version: 3.12 >>>>>>>>>>>>>>>>>>>> GMU/O/AT/! d- s+:+ a C++++ UL++++ P L+++@ E---- W@ N! >>>>>>>>>>>>>>>>>>>> o K? >>>>>>>>>>>>>>>>>>>> w--- >>>>>>>>>>>>>>>>>>>> O- M-- V? PS+++ PEY+ PGP+ t+ 5+ X R tv++ DI++ D++ G+ >>>>>>>>>>>>>>>>>>>> e* >>>>>>>>>>>>>>>>>>>> h-- r >>>>>>>>>>>>>>>>>>>> y+ z+ >>>>>>>>>>>>>>>>>>>> ------END GEEK CODE BLOCK------ >>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>>>>> >>>>>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>>> >>>>>>>>>>>>>>> >>>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>>> Help: >>>>>>>>>>>>>>> >>>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>>> >>>>>>>>>>>>>> >>>>>>>>>>>>>> >>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>>> Help: >>>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>>> Archive: >>>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>>> >>>>>>>>>>>>> >>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>>> Help: >>>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>>> Archive: >>>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>>> >>>>>>>>>>>> >>>>>>>>>>>> >>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>>> Help: >>>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>>> Archive: >>>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>>> _______________________________________________ >>>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>>> Help: >>>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>>> Archive: >>>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> _______________________________________________ >>>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>>> Help: >>>>>>>>>> http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>>> Archive: >>>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>>> >>>>>>>>> >>>>>>>>> _______________________________________________ >>>>>>>>> SkullSpace Discuss Mailing List >>>>>>>>> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>>> Archive: >>>>>>>>> https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>>> _______________________________________________ >>>>>>>> SkullSpace Discuss Mailing List >>>>>>>> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>>> Archive: https://groups.google.com/group/skullspace-discuss-archive/ >>>>>>> >>>>>>> >>>>>>> _______________________________________________ >>>>>>> SkullSpace Discuss Mailing List >>>>>>> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>>>> Archive: https://groups.google.com/group/skullspace-discuss-archive/ >>>>>> >>>>>> >>>>> >>>>> >>>>> _______________________________________________ >>>>> SkullSpace Discuss Mailing List >>>>> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>>> Archive: https://groups.google.com/group/skullspace-discuss-archive/ >>>> _______________________________________________ >>>> SkullSpace Discuss Mailing List >>>> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>>> Archive: https://groups.google.com/group/skullspace-discuss-archive/ >>> >>> >>> _______________________________________________ >>> SkullSpace Discuss Mailing List >>> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >>> Archive: https://groups.google.com/group/skullspace-discuss-archive/ >> >> >> >> _______________________________________________ >> SkullSpace Discuss Mailing List >> Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss >> Archive: https://groups.google.com/group/skullspace-discuss-archive/ > _______________________________________________ > SkullSpace Discuss Mailing List > Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss > Archive: https://groups.google.com/group/skullspace-discuss-archive/ _______________________________________________ SkullSpace Discuss Mailing List Help: http://www.skullspace.ca/wiki/index.php/Mailing_List#Discuss Archive: https://groups.google.com/group/skullspace-discuss-archive/
