The brakes on the H36 move slightly backwards before moving upwards. Get someone to place their fingertips on the brakes with light pressure and try to extend them - that will tell you if you if the problem is present. Regarding anything you do at the back of the brakes like sanding...be careful because if it lets the brakes sit lower the problem will get worse. Gluing some appropriate blocks in the brake cavity can stop the brakes sitting down too low and will resolve the problem. Rob
............................................. ________________________________ From: Nigel Baker <[email protected]> To: [email protected] Sent: Tue, 2 November, 2010 2:12:50 PM Subject: Re: [DOG mailing list] Re:Sticking airbrake G'day Ian. (In the PIKs case I was on final and it is frightening not annoying!!!!). Yes "frightening" is a better description but "annoying" fits my sarcastic sense of humour better. I just lept my cool and worked through the problem same as Rob did. Nige. ----- Original Message ----- >From: Ian Mc Phee >To: [email protected] >Sent: Tuesday, November 02, 2010 1:08 PM >Subject: Re: [DOG mailing list] Re:Sticking airbrake > >I have been caught 3 times in my life and in each case it was soon after >painting First was PIK20E second ?? and third was dimona which had just >been >flown down from Archerfield after being bought from Geoff Edwards (the >Dimona >s importer) Ever since on ground I load all gliders new to me or after >painting with 2 wing stands to simulate flying and check brakes then and >when >airborne check brakes well before landing. In the PIKs case I was on final >and it is frightening not annoying!!!! A quick bunt and it worked but >after >that we (the late Klaus Bretxxxx) set one airbrake to open 3mm before the >other. > > > >On another topic I have now heard of the 3rd failure of coil in Slick 4330 >mag 2 were dimona and other was falke and in all cases none had a jet of >cool >air onto the magneto. I personally think it is a good simple mod on slick >(or >Bendix on L0540). > > > >Bottom line annually always load up glider as if it is flying on ground >and >test brakes then > > >Ian McPhee > > >On 2 November 2010 12:37, Nigel Baker <[email protected]> wrote: > >Yep. >>It's more annoying on final approach. Slowing down seems to fix it when >>that happens. >>With age the spoilers warp. Probably also why yours has had a second >>spring >>added to the spoiler for closing. >>From Rob's and my experience it is due to the rear edge of the spoiler >>catching on the rebate in the wings skin. Fine when they were new >>and straight but not so good at age. >> >>You will have noticed that when the spoiler starts to open it slides >>rearwards first as it lifts. This is a function of the drive geometry. >>We >>chamfered the rear bottom edge of the spoiler with sand paper on on >>sending >>block. Also had to scrape the inside corner of the rebate in the wing >>clean >>off 20 years of Thai Airforce quality maintenance. We used a Stanley >>knife >>blade for this. On one wing we also had to chamfer the top edge of the >>rebate. We did this by dragging a Stanley blade at 90deg to the wing >>along >>this edge to scrape a chamfer. The idea is to make sure all this creates >>a >>ramp affect for the spoiler to pop up over the wing surface in that >>initial >>rearward sliding movement as the spoiler opens. >>Placing cardboard a couple of mm thick under the length of the back edge >>of >>the spoiler then operating will prove if the problems described are the >>true cause. >>Cheers. >>Nige. >> >>----- Original Message ----- >>>From: neville swan >>>To: [email protected] >>>Sent: Tuesday, November 02, 2010 6:06 AM >>>Subject: [DOG mailing list] Re:Sticking airbrake >>> >>> >>>Hi All. >>> >>>Has anyone come across the problem of an airbrake that wont extend? >>>No >>>problem until last weekend when, during the DI, I found it impossible >>>to >>>extend the brakes with the cockpit handle, using a fairly hefty >>>pulling >>>force. I had to slide a feeler gauge under the rear edge brfore I >>>could >>>open the starboard brake panel (the port one is not a problem). I >>>could >>>not see anything amiss and added a small rubber 'buffer' to lift the >>>rear >>>edge a couple of mm., but it did not make any difference. Almost >>>feels >>>as if the torque tube is 'over centre'. Any ideas? >>> >>>Incidently, my brake panels have a small spring at the inboard ends, >>>presumeably to help keep them closed. One panel has had an extra >>>spring >>>added about 3/4 out (not the sticking one). What is the norm? >>> >>>Neville. >
