Hello the problem is solved - the problem has been raised not due to any configsetting and macros - it was my cat, which was walking behind the radio. And over her "cable-walk" she has removed parts of the cables between the different units. So after I replaced and secured all cable again - everything is working well again.
So finally I put up a "Cat-Stop-note" at the shack-table, hihi Thanks everybody for their hints... 73 Karl DL2FAG am Mittwoch, 11. April 2012 um 21:49 schrieben Sie: > Hi Carl: > I assume everything was fine before you made any macro/menu setting changes. > Did you save a K3 configuration file before you made those changes? If so, > try to restore to that configuration using the K3 Utility. I don't beliove > reloading the firmware will do anything as the K3 will remember its settings > independently of the firmware version. > GL > Elliott > ----- Original Message ----- > From: "Karl-Heinz - DL2FAG" <[email protected]> > To: <[email protected]> > Sent: Wednesday, April 11, 2012 12:24 PM > Subject: Re: [Elecraft] Troubel TX on K3 > Hi Elliott > Even with VOX or PTT the same result - no power output in SSB and CW. > In Data Mode - if I push the microphone PTT - a diddle is produced and > I have a power output. > Karl > am Mittwoch, 11. April 2012 um 21:17 schrieben Sie: >> Did you turn on the VOX?? >> ----- Original Message ----- >> From: "Karl-Heinz - DL2FAG" <[email protected]> >> To: <[email protected]> >> Sent: Wednesday, April 11, 2012 11:51 AM >> Subject: Re: [Elecraft] Troubel TX on K3 >> Hello, >> the TX isn't blinking. Have done further test and recognized, that if I >> chooes the FM-Mode - the Power Output was ok. Seems be the K3 does not >> work >> in CW and SSB so far. >> As well the TUNE-button is working as well. >> Karl >> ============================= >> am Mittwoch, 11. April 2012 um 19:58 schrieben Sie: >> Lieber Karl-Heinz, >> First thing to check: Make sure "TX" on right side of display isn't >> blinking. If it is, press and hold TEST. >> 73, >> Hank, W6SX >> On Wed, Apr 11, 2012 at 10:53 AM, Karl-Heinz - DL2FAG <[email protected]> >> wrote: >> Hello, >> I am running into some trouble with the K3 after playing around >> with the unit (macro, settigs etc.) >> After a while I recognized, that the K3 does not transmit - no output in >> CW >> nor >> in SSB - even PTT does work. >> Tuning with the "TUNE-Button" works and give the adjusted output >> power. >> Seems that maybe I have misconfigured a parameter - but doesn't find >> it. >> Any idea from the readers of the refelctors - where I have to look >> for? >> Thanks >> -- >> 73 de >> Karl-Heinz - DL2FAG >> mailto:[email protected] >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> -- >> Mit freundlichen Grüßen >> Karl-Heinz - DL2FAG >> mailto:[email protected] >> ===8<============== Ende des Original Nachrichtentextes ============= -- Mit freundlichen Grüßen Karl-Heinz - DL2FAG mailto:[email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
