But what about us old Head bangers?
From: Wayne Burdick <[email protected]>
To: Elecraft Reflector <[email protected]>
Sent: Sunday, February 15, 2015 4:29 PM
Subject: Re: [Elecraft] KSYN3A - installation question
It is quite easy to swap the synthesizer boards without removing the KRX3
module. I did it blindfolded with a long-haired cat on my lap and the latest
Tom Petty album blasting away.
Wayne
N6KR
On Feb 14, 2015, at 12:38 PM, "Joe Subich, W4TV" <[email protected]> wrote:
>
> I doubt it ... there is not all that much room between the front
> bulkhead and the edge of the KRX3 case. In addition, Wayne mentioned
> the need to reroute some of the cables with may not be possible if
> the KRX3 is in place.
>
> 73,
>
> ... Joe, W4TV
>
>
> On 2015-02-14 10:33 AM, Ken K3IU wrote:
>> I believe that you should ne able to install both boards without
>> removing the KRX3
>> 73, Ken K3IU
>> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>> On 2/14/2015 10:03 AM, Dauer, Edward wrote:
>>> First question that came to my mind when I saw the announcement was
>>> whether the KRX3 had to be removed and reinstalled in order to replace
>>> the
>>> synths. I found installing the KRX3 exasperating when I assembled the K3
>>> - success came on about the 12th try.
>>>
>>> My K3 is 100 miles from where I am right now, so I looked at the
>>> photos in
>>> the K3 assembly manual and those in the new synth instructions, from
>>> which
>>> it appears that the swap could be done without removing the KRX3. Could
>>> we confirm whether R&R is required? Message below says it is.
>>>
>>> If the sub does have to be R&R¹d, anyone have suggestions about how to
>>> reinstall it without the major fuss I experienced?
>>>
>>>
>>> Ted, KN1CBR
>>>
>>>
>>>> ------------------------------
>>>>
>>>> Date: Fri, 13 Feb 2015 13:21:20 -0800
>>>> From: Richard Thorpe <[email protected]>
>>>> To: Elecraft List <[email protected]>
>>>> Subject: [Elecraft] More KSYN3A
>>>> Message-ID: <[email protected]>
>>>> Content-Type: text/plain; charset=utf-8
>>>>
>>>> I talked to Elecraft and you must remove the second receiver not just
>>>> unplug it and remove its ?old? synth board. . . .
>>>>
>>>> R Thorpe K6CG
>>>>
>>>> ------------------------------
>>> ______________________________________________________________
>>> Elecraft mailing list
>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>>> Help: http://mailman.qth.net/mmfaq.htm
>>> Post: mailto:[email protected]
>>>
>>> This list hosted by: http://www.qsl.net
>>> Please help support this email list: http://www.qsl.net/donate.html
>>> Message delivered to [email protected]
>>>
>>
>> ______________________________________________________________
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:[email protected]
>>
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to [email protected]
>>
> ______________________________________________________________
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:[email protected]
>
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to [email protected]
