I tried the cat method. He objected to the ground probe. When my arms heal, I'll try with a clip lead.
73, Mike NF4L > On Feb 15, 2015, at 6:04 PM, Walter Underwood <[email protected]> wrote: > > With no cat, I would recommend Sleater-Kinney. > > wunder > K6WRU > CM87wj > http://observer.wunderwood.org/ > > On Feb 15, 2015, at 2:34 PM, Phil Wheeler <[email protected]> wrote: > >> And those with no cat?:-) >> >> On 2/15/15 1:50 PM, Harry Yingst via Elecraft wrote: >>> But what about us old Head bangers? >>> >>> >>> >>> >>> From: Wayne Burdick <[email protected]> >>> To: Elecraft Reflector <[email protected]> >>> Sent: Sunday, February 15, 2015 4:29 PM >>> Subject: Re: [Elecraft] KSYN3A - installation question >>> It is quite easy to swap the synthesizer boards without removing the KRX3 >>> module. I did it blindfolded with a long-haired cat on my lap and the >>> latest Tom Petty album blasting away. >>> >>> Wayne >>> N6KR >>> >>> >>> On Feb 14, 2015, at 12:38 PM, "Joe Subich, W4TV" <[email protected]> wrote: >>> >>>> I doubt it ... there is not all that much room between the front >>>> bulkhead and the edge of the KRX3 case. In addition, Wayne mentioned >>>> the need to reroute some of the cables with may not be possible if >>>> the KRX3 is in place. >>>> >>>> 73, >>>> >>>> ... Joe, W4TV >>>> >>>> >>>> On 2015-02-14 10:33 AM, Ken K3IU wrote: >>>>> I believe that you should ne able to install both boards without >>>>> removing the KRX3 >>>>> 73, Ken K3IU >>>>> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ >>>>> On 2/14/2015 10:03 AM, Dauer, Edward wrote: >>>>>> First question that came to my mind when I saw the announcement was >>>>>> whether the KRX3 had to be removed and reinstalled in order to replace >>>>>> the >>>>>> synths. I found installing the KRX3 exasperating when I assembled the K3 >>>>>> - success came on about the 12th try. >>>>>> >>>>>> My K3 is 100 miles from where I am right now, so I looked at the >>>>>> photos in >>>>>> the K3 assembly manual and those in the new synth instructions, from >>>>>> which >>>>>> it appears that the swap could be done without removing the KRX3. Could >>>>>> we confirm whether R&R is required? Message below says it is. >>>>>> >>>>>> If the sub does have to be R&R¹d, anyone have suggestions about how to >>>>>> reinstall it without the major fuss I experienced? >>>>>> >>>>>> >>>>>> Ted, KN1CBR >>>>>> >>>>>> >>>>>>> ------------------------------ >>>>>>> >>>>>>> Date: Fri, 13 Feb 2015 13:21:20 -0800 >>>>>>> From: Richard Thorpe <[email protected]> >>>>>>> To: Elecraft List <[email protected]> >>>>>>> Subject: [Elecraft] More KSYN3A >>>>>>> Message-ID: <[email protected]> >>>>>>> Content-Type: text/plain; charset=utf-8 >>>>>>> >>>>>>> I talked to Elecraft and you must remove the second receiver not just >>>>>>> unplug it and remove its ?old? synth board. . . . >>>>>>> >>>>>>> R Thorpe K6CG >>>>>>> >>>>>>> ------------------------------ >>>>>> ______________________________________________________________ >>>>>> Elecraft mailing list >>>>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>>>> Help: http://mailman.qth.net/mmfaq.htm >>>>>> Post: mailto:[email protected] >>>>>> >>>>>> This list hosted by: http://www.qsl.net >>>>>> Please help support this email list: http://www.qsl.net/donate.html >>>>>> Message delivered to [email protected] >>>>>> >>>>> ______________________________________________________________ >>>>> Elecraft mailing list >>>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>>> Help: http://mailman.qth.net/mmfaq.htm >>>>> Post: mailto:[email protected] >>>>> >>>>> This list hosted by: http://www.qsl.net >>>>> Please help support this email list: http://www.qsl.net/donate.html >>>>> Message delivered to [email protected] >>>>> >>>> ______________________________________________________________ >>>> Elecraft mailing list >>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>> Help: http://mailman.qth.net/mmfaq.htm >>>> Post: mailto:[email protected] >>>> >>>> This list hosted by: http://www.qsl.net >>>> Please help support this email list: http://www.qsl.net/donate.html >>>> Message delivered to [email protected] >>> ______________________________________________________________ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:[email protected] >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> Message delivered to [email protected] >>> >>> ______________________________________________________________ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:[email protected] >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> Message delivered to [email protected] >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to [email protected] > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
