As previously noted, the new revision of EN 301489-1(EMC for radio) does
increase the range to 2 GHz and does reference EN61000-4-3. It appears to be
the first product/family standard to do so. Will shall see if others follow.
Richard Woods
----------
From: Pettit, Ghery [SMTP:[email protected]]
Sent: Thursday, September 06, 2001 12:18 PM
To: '[email protected]'; [email protected]
Cc: [email protected]
Subject: RE: Power Amplifier for 2 GHz Immunity
The question that would then arise is this - what standard using EN
61000-4-3 calls out immunity testing above 1 GHz? EN 55024:1998 for
ITE
does not, nor does CISPR 24 upon which it is based. Unless a
standard using
EN 61000-4-3 as a test method requires immunity testing above 1 GHz,
the
added procedure has no meaning for a particular product.
Ghery Pettit
Intel
-----Original Message-----
From: [email protected]
[mailto:[email protected]]
Sent: Thursday, September 06, 2001 8:41 AM
To: [email protected]
Cc: [email protected]
Subject: RE: Power Amplifier for 2 GHz Immunity
Bob,
EN 301489-1 due in 2003 calls for radiated immunity testing to 2
GHz.
EN61000-4-3 also indicates testing to 2 GHz due to the portable
phone
market.
Best regards,
Don Umbdenstock
Sensormatic Electronics Corporation
> ----------
> From: [email protected][SMTP:[email protected]]
> Sent: Thursday, September 06, 2001 11:15 AM
> To: [email protected]
> Cc: [email protected]
> Subject: Re: Power Amplifier for 2 GHz Immunity
>
>
> We have recently purchased an Amplifier Research Model 25SIG4A and
we use
> an
> AR FP2080 probe. We have two antennas for that range, a Schaffner
bilog
> and
> an
> A. H. Systems horn.
>
> Other than the upcoming 60601-1-2 for medical equipment, are there
any
> other upcoming
> standards that call out immunity testing over a gig? To my
knowledge no
> present standard
> does.
>
> Bob Heller
> 3M Product Safety, 76-1-01
> St. Paul, MN 55107-1208
> Tel: 651- 778-6336
> Fax: 651-778-6252
>
>
==========================================================================
> ====
>
>
>
>
> UMBDENSTOCK@Senso
>
> rmatic.com To:
> [email protected]
> cc: (bcc: Robert E.
> Heller/US-Corporate/3M/US)
> 09/05/2001 10:19 Subject: Power
Amplifier
> for 2 GHz Immunity
> AM
>
> Please respond to
>
> UMBDENSTOCK
>
>
>
>
>
>
>
>
>
>
>
> Hello Forum,
>
> I was wondering what amplifier you are using for the 2 GHz testing
> requirement of EN61000-4-3? Any comments regarding "if I had to
do it
> over
> again, I would have . . . " relative to your 2 GHz setup?
>
> Best regards,
>
> Don Umbdenstock
>
> Sensormatic
>
>
>
> -------------------------------------------
> This message is from the IEEE EMC Society Product Safety
> Technical Committee emc-pstc discussion list.
>
> Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/
>
> To cancel your subscription, send mail to:
> [email protected]
> with the single line:
> unsubscribe emc-pstc
>
> For help, send mail to the list administrators:
> Michael Garretson: [email protected]
> Dave Heald [email protected]
>
> For policy questions, send mail to:
> Richard Nute: [email protected]
> Jim Bacher: [email protected]
>
> All emc-pstc postings are archived and searchable on the web at:
> No longer online until our new server is brought online and
the old
> messages are imported into the new server.
>
>
>
>
-------------------------------------------
This message is from the IEEE EMC Society Product Safety
Technical Committee emc-pstc discussion list.
Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/
To cancel your subscription, send mail to:
[email protected]
with the single line:
unsubscribe emc-pstc
For help, send mail to the list administrators:
Michael Garretson: [email protected]
Dave Heald [email protected]
For policy questions, send mail to:
Richard Nute: [email protected]
Jim Bacher: [email protected]
All emc-pstc postings are archived and searchable on the web at:
No longer online until our new server is brought online and the
old
messages are imported into the new server.
-------------------------------------------
This message is from the IEEE EMC Society Product Safety
Technical Committee emc-pstc discussion list.
Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/
To cancel your subscription, send mail to:
[email protected]
with the single line:
unsubscribe emc-pstc
For help, send mail to the list administrators:
Michael Garretson: [email protected]
Dave Heald [email protected]
For policy questions, send mail to:
Richard Nute: [email protected]
Jim Bacher: [email protected]
All emc-pstc postings are archived and searchable on the web at:
No longer online until our new server is brought online and the
old messages are imported into the new server.
-------------------------------------------
This message is from the IEEE EMC Society Product Safety
Technical Committee emc-pstc discussion list.
Visit our web site at: http://www.ewh.ieee.org/soc/emcs/pstc/
To cancel your subscription, send mail to:
[email protected]
with the single line:
unsubscribe emc-pstc
For help, send mail to the list administrators:
Michael Garretson: [email protected]
Dave Heald [email protected]
For policy questions, send mail to:
Richard Nute: [email protected]
Jim Bacher: [email protected]
All emc-pstc postings are archived and searchable on the web at:
No longer online until our new server is brought online and the old
messages are imported into the new server.
