Perhaps I mis-stated. What I actually need is an EMC design checklist that
a
design project team can use to determine and satisfy themselves that EMC
has been considered and implemented on a given design project.
Bob Heller
Senior EMC Engineer
3M EMC Laboratory, 76-1-01
St. Paul, MN 55107-1208
Tel: 651- 778-6336
Fax: 651-778-6252
=======================================================
"Grasso, Charles"
<Charles.Grasso@ec To: "'robert Macy'"
<[email protected]>
hostar.com> "'[email protected]'"
<[email protected]>
"'[email protected]'" <[email protected]>
03/08/2004 12:08 cc:
PM Subject: RE: EMC Checklist
I would hesitate in implementing a checklist.
They are OK as a first cut - but a much better approach
would be to look up a local EMC Chapter and attend a
few pertinent meetings.
Best Regards
Charles Grasso
Senior Compliance Engineer
Echostar Communications Corp.
Tel: 303-706-5467
Fax: 303-799-6222
Cell: 303-204-2974
Email: [email protected];
Email Alternate: [email protected]
From: robert Macy [mailto:[email protected]]
Sent: Monday, March 08, 2004 9:12 AM
To: [email protected]; [email protected]
Subject: Re: EMC Checklist
These appeared here earlier.
PCB Checklist
http://www.xilinx.com/xlnx/xil_prodcat_product.jsp?title=si_pcbcheck
page of EMC info
http://www.credencetech.com/emc.htm
Someone's thesis?
http://www.geocities.com/timfoo6143/Design_Rules.pdf
another section
http://www.geocities.com/timfoo6143/SI_vs_EMI.pdf
- Robert -
Robert A. Macy, PE .. [email protected]
408 286 3985 . . . .. . . fx 408 297 9121
AJM International Electronics Consultants
101 E San Fernando, Suite 402
San Jose, CA 95112
On Mon, 8 Mar 2004 04:17:32 -0600
[email protected] wrote:
>
>
>
>
>
> Does anyone have an EMC checklist for PC board designers
> that they could
> share?
> Or could you point me to where I may obtain one? I have
> the opportunity to
> provide
>
> Thanks in advance,
> Bob Heller
> Senior EMC Engineer
> 3M EMC Laboratory, 76-1-01
> St. Paul, MN 55107-1208
> Tel: 651- 778-6336
> Fax: 651-778-6252
> =======================================================
>
>
> -------------------------------------------
> This message is from the IEEE EMC Society Product Safety
> Technical Committee emc-pstc discussion list.
>
> Visit our web site at: http://www.ieee-pses.org/
>
> To cancel your subscription, send mail to:
> [email protected]
> with the single line:
> unsubscribe emc-pstc
>
> For help, send mail to the list administrators:
> Ron Pickard: [email protected]
> Dave Heald: [email protected]
>
> For policy questions, send mail to:
> Richard Nute: [email protected]
> Jim Bacher: [email protected]
>
> All emc-pstc postings are archived and searchable on the
> web at:
> http://www.ieeecommunities.org/emc-pstc
This message is from the IEEE EMC Society Product Safety
Technical Committee emc-pstc discussion list.
Visit our web site at: http://www.ieee-pses.org/
To cancel your subscription, send mail to:
[email protected]
with the single line:
unsubscribe emc-pstc
For help, send mail to the list administrators:
Ron Pickard: [email protected]
Dave Heald: [email protected]
For policy questions, send mail to:
Richard Nute: [email protected]
Jim Bacher: [email protected]
All emc-pstc postings are archived and searchable on the web at:
http://www.ieeecommunities.org/emc-pstc
This message is from the IEEE EMC Society Product Safety
Technical Committee emc-pstc discussion list.
Visit our web site at: http://www.ieee-pses.org/
To cancel your subscription, send mail to:
[email protected]
with the single line:
unsubscribe emc-pstc
For help, send mail to the list administrators:
Ron Pickard: [email protected]
Dave Heald: [email protected]
For policy questions, send mail to:
Richard Nute: [email protected]
Jim Bacher: [email protected]
All emc-pstc postings are archived and searchable on the web at:
http://www.ieeecommunities.org/emc-pstc
