Gents Whilst neither of the amendments referred to below affect the sort of equipment we produce or test it is "interesting" and not uncommon that there is a delay between the publication of the IEC version and the BS EN version. I have always applied the BS EN version. Am I correct in following this rationale? The latest BS EN version is equivalent to IEC61326: 1997 including amendments 1 and 2. Ian Gordon > -----Original Message----- > From: Helge Knudsen [mailto:[email protected]] > Sent: 23 April 2004 07:48 > To: 'John Barnes'; [email protected] > Subject: SV: EN/IEC 61326 Harmonized Standard for Laboratory Equipment > > > > Hello John, > > Addition of Annex E and F are new, there are no other differences. > > ********* > Annex E (normative) Test configurations, operational conditions and > performance criteria for portable test, measuring and > monitoring equipment > used in low-voltage distribution systems. > Annex F (normative) Test configurations, operational conditions and > performance criteria for transducers with integrated or remote signal > conditioning. > ************ > > Best regards > > > Helge Knudsen > Test & Approval > Niros Telecommunication > Hirsemarken 5 > DK-3520 Farum > Tel +45 44 34 22 51 > Fax +45 44 99 28 08 > email [email protected] > > > -----Oprindelig meddelelse----- > Fra: John Barnes [mailto:[email protected]] > Sendt: 22. april 2004 17:41 > Til: [email protected] > Emne: EN/IEC 61326 Harmonized Standard for Laboratory Equipment > > > > EMC/PSTC'ers, > What are the differences (if any) between IEC 61326:2002 and IEC > 61326:1997 +A1:1998 +A2:2000? The title page on the 2002 > edition shows > "First edition 2002-02 Electrical equipment for measurement, control > and laboratory use - EMC requirements". > > The December 11, 2003 issue (C271) of the Official Journal of the > European Union (OJ) lists EN 61326:1997 +A1:1998 +A2:2001 as a > Harmonized Standard under the EMC Directive. The references show that > this EN standard is identical to IEC 61326:1997 +A1:1998 +A2:2000. > > We bought IEC 61326, and received the 2002 version, which on > page 7 says > "This standard cancels and replaces the first edition of IEC > 61326-1 published in 1997, its amendment 1 (1998) and its > amendment 2 (2000) and constitutes a technical revision. > > The text of this standard is based on the following documents: > FDIS Report on Voting > 85A/345/FDIS 65A/348/RVD" > > Thanks! > John Barnes KS4GL, PE, NCE, ESDC Eng, SM IEEE > dBi Corporation > http://www.dbicorporation.com/
*********************************************************************** This email is confidential and intended solely for the use of the individual to whom it is addressed. Any views or opinions presented are solely those of the author and do not necessarily represent those of the BOC Group plc or any of its affiliates. If you are not the intended recipient, be advised that you have received this email in error and that any use, dissemination, forwarding, printing, or copying of this email is strictly prohibited. If you have received this email in error please return the message to the sender by replying to it and then delete the message from your computer. This footnote also confirms that this email message has been checked by anti-virus software for the presence of computer viruses. However, the BOC Group plc or any of its affiliates accepts no responsibility for any virus or defect that might arise from opening this e-mail or attachments. This message is from the IEEE EMC Society Product Safety Technical Committee emc-pstc discussion list. Visit our web site at: http://www.ieee-pses.org/ To cancel your subscription, send mail to: [email protected] with the single line: unsubscribe emc-pstc For help, send mail to the list administrators: Ron Pickard: [email protected] Dave Heald: [email protected] For policy questions, send mail to: Richard Nute: [email protected] Jim Bacher: [email protected] All emc-pstc postings are archived and searchable on the web at: http://www.ieeecommunities.org/emc-pstc
