10.10.10.10 is a static IP hardcoded into the 7i92 hardware. If you get "ETH device 7i92 at ip 10.10.10.10", then the card's on a working ethernet and powered up and responding to mesaflash's ping. I asked for the dump of its pinout config and it responded correctly.
My internet's off a USB dongle. It's been working fine. No, no LinuxCNC axis moves. If I expand FERROR way out, the display says it's moving like 0.5" before erroring- but the physical axis never moves. Danny On 5/27/2016 11:21 PM, Gene Heskett wrote: > On Friday 27 May 2016 23:30:23 dan...@austin.rr.com wrote: > > And you are top podsting, making it hard to follow the conversation. >> OK the interfaces file is: >> # The loopback network interface >> auto lo >> iface lo inet loopback >> auto eth1 >> iface eth1 inet static >> address 10.10.10.1 >> >> BTW that dmesg gave that from grepping "eth" alone. There is no eth1 >> there, only eth0. >> >> So I changed "eth1" to "eth0" in interfaces and "sudo service >> networking restart". >> >> Now I asked mesaflash and got: >> ETH device 7I92 at ip=10.10.10.10 >> > Now I am confused, and I don't think the 10.10.10.10 address is coming > from eth0, but from the mesanet cards, and I am not familiar with the > ethernet interfaces the mesa cards can expose, so I believe I'll bow out > and ask Peter C. Wallace to bail us out as he knows this stuff much much > better than I. > >> So, GREAT, ran LinuxCNC, but got the same following error upon axis >> motion. > Is the axis moving? > >> Rebooted. LinuxCNC still gives the same following error. >> >> Now dmesg has: >> [ 1.837260] tg3 0000:03:08.0: eth0: Tigon3 [partno(BCM95788) rev >> 3003] (PCI:33MHz:32-bit) MAC address 00:16:17:ad:3f:ea [ 1.837266] >> tg3 0000:03:08.0: eth0: attached PHY is 5705 (10/100/1000Base-T >> Ethernet) (WireSpeed[0], EEE[0]) [ 1.837271] tg3 0000:03:08.0: >> eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ >> 1.837275] tg3 0000:03:08.0: eth0: dma_rwctrl[763f0000] >> dma_mask[32-bit] [ 12.808639] ADDRCONF(NETDEV_UP): eth0: link is not >> ready >> > Then something is amiss in the interfaces file. Which is a different path > than the mesa cards are showing. That is not thru the eth0 interface at > all. > >> But again, mesaflash says it's there at 10.10.10.10. And if you try >> to start LinuxCNC without the 7i92 powered up, it won't let you start >> LinuxCNC, not wait to move an axis. >> >> Danny >> >> ---- dan...@austin.rr.com wrote: >>> Alrighty! >>> >>> OK, found and renamed that .rules to a .rules.bak file and rebooted. >>> >>> Can't see the 7i92 now. Mesaflash --device 7i92 --addr 10.10.10.10 >>> gives "not found". >>> >>> dmesg has no "ifname" in it at all. >>> >>> It does have: >>> [ 1.820851] tg3 0000:03:08.0: eth0: Tigon3 [partno(BCM95788) rev >>> 3003] (PCI:33MHz:32-bit) MAC address 00:16:17:ad:3f:ea [ >>> 1.820858] tg3 0000:03:08.0: eth0: attached PHY is 5705 >>> (10/100/1000Base-T Ethernet) (WireSpeed[0], EEE[0]) [ 1.820862] >>> tg3 0000:03:08.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] >>> TSOcap[1] [ 1.820866] tg3 0000:03:08.0: eth0: >>> dma_rwctrl[763f0000] dma_mask[32-bit] >>> >>> Danny >>> >>> ---- Gene Heskett <ghesk...@shentel.net> wrote: >>>> On Friday 27 May 2016 12:54:22 dan...@austin.rr.com wrote: >>>> >>>> I've sent this message 3 times now. What black hole is gobbling >>>> it up? >>>> >>>>> It's a direct dd copy of the drive. If that wasn't complete, a >>>>> lot more would be broken. >>>>> >>>>> I would not dismantle the (mostly) working system like that. >>>>> There's a risk of something getting stored wrong on the working >>>>> drive while it's on the new machine, and I don't see anything to >>>>> prove by moving it. >>>>> >>>>> 99.9% sure it's just something different about the ethernet >>>>> driver on the new motherboard. Something small. No idea how to >>>>> fix it, though. >>>> See my reply to Peter, delete >>>> /etc/udev/rules.d/70-persistent-net.rules and reboot. It will be >>>> rebuilt to match the ethernet hardware in finds as it reboots, and >>>> networking will likely be restored. >>>> >>>> If not, delete it again, grep ' ifname ' /var/log/dmesg to see >>>> what it did call it, you should get something that resembles this: >>>> >>>> gene@coyote:~$ grep ' ifname ' /var/log/dmesg >>>> [ 1.401462] forcedeth 0000:00:08.0: ifname eth0, PHY OUI 0x5043 >>>> @ 1, addr 00:1f:c6:62:fc:bb >>>> [ 1.929064] forcedeth 0000:00:09.0: ifname eth1, PHY OUI 0x5043 >>>> @ 1, addr 00:1f:c6:63:07:97 >>>> (word wrapped, darn it, what you want is the string after the >>>> first ifname. in this example eth0) >>>> >>>> then use an editor as root to look at the >>>> /etc/networking/interfaces file, and rename the stanza for eth0 to >>>> whatever the system found and named it to in the /var/log/dmesg >>>> file. >>>> >>>> You should at that point be able to do a "sudu service restart >>>> networking" and have the ability to "ping -C2 yahoo.com" and get a >>>> 2 normal ping responses from yahoo.com which indicates that >>>> networking is now working. >>>> >>>>> It is an AMD64 though, and the installation was an i686. >>>> A non-issue AFAIK. >>>> >>>>> Danny >>>>> >>>>> ---- "Peter C. Wallace" <p...@mesanet.com> wrote: >>>>>> On Fri, 27 May 2016, Danny Miller wrote: >>>>>>> Date: Fri, 27 May 2016 00:11:08 -0500 >>>>>>> From: Danny Miller <dan...@austin.rr.com> >>>>>>> Reply-To: "Enhanced Machine Controller (EMC)" >>>>>>> <emc-users@lists.sourceforge.net> >>>>>>> To: emc-users@lists.sourceforge.net >>>>>>> Subject: Re: [Emc-users] Copying an installation >>>>>>> >>>>>>> I do recall we went through much more than expected just >>>>>>> getting all that installed. And I don't have a complete >>>>>>> list of all that was done. >>>>>>> >>>>>>> I did poke around again on this machine. >>>>>>> >>>>>>> Mesaflash says the card's there at 10.10.10.10. >>>>>>> >>>>>>> After launching LinuxCNC, the VFD does respond to commands >>>>>>> just fine. >>>>>>> >>>>>>> I experimented with the FERROR value- it'll allow the >>>>>>> coordinates to change significantly before throwing an >>>>>>> error, but the axes will never move regardless. The 7i92 >>>>>>> won't put out steps at all. I don't have any enable line on >>>>>>> it. >>>>>>> >>>>>>> Danny >>>>>> Did you try swapping hard drives as someone suggested, in case >>>>>> something was forgotten when moving? >>>>>> >>>>>> (when linux using generic kernels its much easier to just swap >>>>>> hard drives than moving a setup to a new machine) >>>>>> >>>>>>> On 5/22/2016 6:27 PM, andy pugh wrote: >>>>>>>> On 22 May 2016 at 19:51, Danny Miller >>>>>>>> <dan...@austin.rr.com> >>>> wrote: >>>>>>>>> Any advice, folks? I've gotta move off that Dell machine >>>>>>>>> ASAP and really want to avoid a whole reinstall. >>>>>>>> I would suggest a complete reinstall of the OS and >>>>>>>> LinuxCNC, but keep the same config files. The LinuxCNC >>>>>>>> config files should be entirely portable. >>>>>>> ------------------------------------------------------------ >>>>>>> ------ ------------ What NetFlow Analyzer can do for you? >>>>>>> Monitors network bandwidth and traffic patterns at an >>>>>>> interface-level. Reveals which users, apps, and protocols >>>>>>> are consuming the most bandwidth. Provides multi-vendor >>>>>>> support for NetFlow, J-Flow, sFlow and other flows. Make >>>>>>> informed decisions using capacity planning reports. >>>>>>> https://ad.doubleclick.net/ddm/clk/305295220;132659582;e >>>>>>> _______________________________________________ >>>>>>> Emc-users mailing list >>>>>>> Emc-users@lists.sourceforge.net >>>>>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>>>> Peter Wallace >>>>>> Mesa Electronics >>>>>> >>>>>> (\__/) >>>>>> (='.'=) This is Bunny. Copy and paste bunny into your >>>>>> (")_(") signature to help him gain world domination. >>>>>> >>>>>> >>>>>> -------------------------------------------------------------- >>>>>> ------ ---------- What NetFlow Analyzer can do for you? >>>>>> Monitors network bandwidth and traffic patterns at an >>>>>> interface-level. Reveals which users, apps, and protocols are >>>>>> consuming the most bandwidth. Provides multi-vendor support >>>>>> for NetFlow, J-Flow, sFlow and other flows. Make informed >>>>>> decisions using capacity planning reports. >>>>>> https://ad.doubleclick.net/ddm/clk/305295220;132659582;e >>>>>> _______________________________________________ >>>>>> Emc-users mailing list >>>>>> Emc-users@lists.sourceforge.net >>>>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>>> ---------------------------------------------------------------- >>>>> ------ -------- What NetFlow Analyzer can do for you? Monitors >>>>> network bandwidth and traffic patterns at an interface-level. >>>>> Reveals which users, apps, and protocols are consuming the most >>>>> bandwidth. Provides multi-vendor support for NetFlow, J-Flow, >>>>> sFlow and other flows. Make informed decisions using capacity >>>>> planning reports. >>>>> https://ad.doubleclick.net/ddm/clk/305295220;132659582;e >>>>> _______________________________________________ >>>>> Emc-users mailing list >>>>> Emc-users@lists.sourceforge.net >>>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>> Cheers, Gene Heskett >>>> -- >>>> "There are four boxes to be used in defense of liberty: >>>> soap, ballot, jury, and ammo. Please use in that order." >>>> -Ed Howdershelt (Author) >>>> Genes Web page <http://geneslinuxbox.net:6309/gene> >>>> >>>> ------------------------------------------------------------------ >>>> ------------ What NetFlow Analyzer can do for you? Monitors network >>>> bandwidth and traffic patterns at an interface-level. Reveals >>>> which users, apps, and protocols are consuming the most bandwidth. >>>> Provides multi-vendor support for NetFlow, J-Flow, sFlow and other >>>> flows. Make informed decisions using capacity planning reports. >>>> https://ad.doubleclick.net/ddm/clk/305295220;132659582;e >>>> _______________________________________________ >>>> Emc-users mailing list >>>> Emc-users@lists.sourceforge.net >>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>> -------------------------------------------------------------------- >>> ---------- What NetFlow Analyzer can do for you? Monitors network >>> bandwidth and traffic patterns at an interface-level. Reveals which >>> users, apps, and protocols are consuming the most bandwidth. >>> Provides multi-vendor support for NetFlow, J-Flow, sFlow and other >>> flows. Make informed decisions using capacity planning reports. >>> https://ad.doubleclick.net/ddm/clk/305295220;132659582;e >>> _______________________________________________ >>> Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users >> ---------------------------------------------------------------------- >> -------- What NetFlow Analyzer can do for you? Monitors network >> bandwidth and traffic patterns at an interface-level. Reveals which >> users, apps, and protocols are consuming the most bandwidth. Provides >> multi-vendor support for NetFlow, J-Flow, sFlow and other flows. Make >> informed decisions using capacity planning reports. >> https://ad.doubleclick.net/ddm/clk/305295220;132659582;e >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users > > Cheers, Gene Heskett ------------------------------------------------------------------------------ What NetFlow Analyzer can do for you? Monitors network bandwidth and traffic patterns at an interface-level. Reveals which users, apps, and protocols are consuming the most bandwidth. Provides multi-vendor support for NetFlow, J-Flow, sFlow and other flows. Make informed decisions using capacity planning reports. https://ad.doubleclick.net/ddm/clk/305295220;132659582;e _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
