thanks peter

and just to confirm

is there any possibility of using the 7i77 for this?  I am just a bit cagey
to connect up if it is not optically isolated as I have a 30 years old
fanuc vfd I am connecting to and I really don't want to blow it up lol

regards

Andrew

On Fri, Nov 6, 2020 at 12:05 PM Peter C. Wallace <p...@mesanet.com> wrote:

> On Fri, 6 Nov 2020, andrew beck wrote:
>
> > Date: Fri, 6 Nov 2020 11:47:58 +1300
> > From: andrew beck <andrewbeck0...@gmail.com>
> > Reply-To: "Enhanced Machine Controller (EMC)"
> >     <emc-users@lists.sourceforge.net>
> > To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net
> >
> > Subject: Re: [Emc-users] how to control lathe spindle with a mesa 7i77
> card
> >
> > just another question for peter
> >
> > can you just confirm how the 7i77 and 7i77 spindle controls differ
> please.
> > and if I connect up a spinx1 board do I need flash a pin file into the
> 6i25
> > or should it just work with the stock 6i52x7i77 config regards
> >
> > andrew
>
> You would need firmware that has a PWMgen on the second 6I25 connector
> (5i25_7i77_7i78.bit is one possibility)
>
> >
> > On Fri, Nov 6, 2020 at 8:56 AM andrew beck <andrewbeck0...@gmail.com>
> wrote:
> >
> >> hey peter just a quick question on this spinx1 card
> >>
> >> this looks just what I need  just want to confirm a few things
> >>
> >> my fanuc drive takes a 0-10v signal.  10v comes out from drive and it
> has
> >> a wiper and 0v just like a POT.  I know I can use a 7i76 easily to run
> it.
> >>
> >> just checking that the spindx1 is the same idea.  I saw reference in the
> >> manual to a 5-18v input voltage from drive.  since my input voltage is
> 10v
> >> am I good to go?
> >>
> >> the price is right on that little card and it looks perfect.  I might
> use
> >> a spare 7i76 now with the 7i77 and replace it once make my next order of
> >> mesa cards
> >> regards
> >>
> >> Andrew
> >>
> >> On Tue, Nov 3, 2020 at 4:42 AM Peter C. Wallace <p...@mesanet.com>
> wrote:
> >>
> >>> On Mon, 2 Nov 2020, andrew beck wrote:
> >>>
> >>>> Date: Mon, 2 Nov 2020 22:31:32 +1300
> >>>> From: andrew beck <andrewbeck0...@gmail.com>
> >>>> Reply-To: "Enhanced Machine Controller (EMC)"
> >>>>     <emc-users@lists.sourceforge.net>
> >>>> To: "Enhanced Machine Controller (EMC)" <
> >>> emc-users@lists.sourceforge.net>
> >>>> Subject: Re: [Emc-users] how to control lathe spindle with a mesa 7i77
> >>> card
> >>>>
> >>>> Thanks Jon.
> >>>>
> >>>> I am controlling a 1988 fanuc velocity spindle drive.  And no Idea
> about
> >>>> isolation.  Not keen to try it lol.  Really I just want a isolated
> 0-10v
> >>>> virtual pot like the Mesa 7i76 has.  Otherwise I might daisy chain in
> a
> >>>> 7i76 just for the spindle io. but that is such a waste lol.
> >>>
> >>>
> >>> If you have a spare parallel expansion slot, you could use a SPINx1
> >>>
> >>> Peter Wallace
> >>> Mesa Electronics
> >>>
> >>>
> >>>
> >>> _______________________________________________
> >>> Emc-users mailing list
> >>> Emc-users@lists.sourceforge.net
> >>> https://lists.sourceforge.net/lists/listinfo/emc-users
> >>>
> >>
> >
> > _______________________________________________
> > Emc-users mailing list
> > Emc-users@lists.sourceforge.net
> > https://lists.sourceforge.net/lists/listinfo/emc-users
> >
>
> Peter Wallace
> Mesa Electronics
>
> (\__/)
> (='.'=) This is Bunny. Copy and paste bunny into your
> (")_(") signature to help him gain world domination.
>
>
>
> _______________________________________________
> Emc-users mailing list
> Emc-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/emc-users
>

_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Reply via email to