Yes, you will need the extra memory on the blades in question. You can do a “show system utilization storage” to see which modules do/don’t have the memory. Long ago, certain features required only 256MB on the module configured for the feature. Around the date of your firmware, it became a requirement to have 256MB in all modules within the chassis.
From Release Notes: The following features require that 256MB of DRAM be installed in all modules in the chassis: · Protocol Independent Multicast (PIM) · Extended routing capacities · Load Share Network Address Translation (LSNAT) · Network Address Translation (NAT) · Transparent Web Cache Balancing (TWCB) · Radius Snooping · NetFlow Likewise, you’ll need the 256MB upgrade for each blade if/when you upgrade the N7 to firmware 7.11 or later. There’s also a transition doc on how to work through the upgrade as some config items need to be tended to before upgrading. From: Luis Oliveira [mailto:[email protected]] Sent: Thursday, November 13, 2014 3:24 PM To: Enterasys Customer Mailing List Subject: Re: [enterasys] Cannot enable PIM on N7 You need at least 256M Ram to run pim . My two cents Regares Enviado do meu iPhone No dia 13/11/2014, às 21:18, "[email protected]<mailto:[email protected]>" <[email protected]<mailto:[email protected]>> escreveu: It's weird because I'm running it on one of the N7s but the other one doesn't have the option. I thought it was a problem with the advanced license but that unit has been running OSPF for years now which wouldn't be happening with a bad license. Joshua Sanders Asst. Vice President - Systems Operations Western Mutual Insurance Group PO Box 19626 | Irvine, CA 92623-9626 From: Reese Borel <[email protected]<mailto:[email protected]>> To: "Enterasys Customer Mailing List" <[email protected]<mailto:[email protected]>> Date: 11/13/2014 12:53 PM Subject: RE: [enterasys] Cannot enable PIM on N7 ________________________________ Same here. We are running it but with 7.x firmware. Thanks, Reese From: Yingst, Christopher [mailto:[email protected]] Sent: Thursday, November 13, 2014 9:57 AM To: Enterasys Customer Mailing List Subject: Re: [enterasys] Cannot enable PIM on N7 We are have PIM-SM running on those blades, but we are at FW 07.66.04.0002 Chris Yingst - Consultant ECE - Networking | Network Security 207.619.4472 From: "[email protected]<mailto:[email protected]>" <[email protected]<mailto:[email protected]>> Reply-To: "[email protected]<mailto:[email protected]>" <[email protected]<mailto:[email protected]>> Date: Thursday, November 13, 2014 at 10:43 AM To: Enterasys Customer Mailing List <[email protected]<mailto:[email protected]>> Subject: [enterasys] Cannot enable PIM on N7 I have two identical N7 chassis switches at my two corporate offices. The only differences is two blades in my corporate office are 10/100 7H4382-49s and the 2 blades in the matching chassis at my DR site are 10/100/1000 7G4285-49. Both units are running the 6.12.08.003 firmware and I have the advanced routing license installed on both units. For some reason I can't run a ip pim command from the router config. It looks like nat, slb, and twcb are unavailable as well. Is this a limitation of the 7H4382 DFE? Joshua Sanders Asst. Vice President - Systems Operations Western Mutual Insurance Group PO Box 19626 | Irvine, CA 92623-9626 * --To unsubscribe from enterasys, send email to [email protected]<mailto:[email protected]> with the body: unsubscribe enterasys [email protected]<mailto:[email protected]> ________________________________ NOTICE - This communication may contain confidential and privileged information that is for the sole use of the intended recipient. Any viewing, copying or distribution of, or reliance on this message by unintended recipients is strictly prohibited. If you have received this message in error, please notify us immediately by replying to the message and deleting it from your computer. * --To unsubscribe from enterasys, send email to [email protected]<mailto:[email protected]> with the body: unsubscribe enterasys [email protected]<mailto:[email protected]> The information transmitted, including any attachments, is intended only for the person or entity to which it is addressed and may contain confidential and/or privileged material. Any review, retransmission, dissemination or other use of, or taking of any action in reliance upon, this information by persons or entities other than the intended recipient is prohibited, and all liability arising therefrom is disclaimed. If you received this in error, please contact the sender and delete the material from any computer. Axiall Corporation (formerly known as Georgia Gulf corporation) is a Delaware corporation. This communication may come from Axiall Corporation or one of its subsidiaries. * --To unsubscribe from enterasys, send email to [email protected]<mailto:[email protected]> with the body: unsubscribe enterasys [email protected]<mailto:[email protected]> * --To unsubscribe from enterasys, send email to [email protected]<mailto:[email protected]> with the body: unsubscribe enterasys [email protected]<mailto:[email protected]> * --To unsubscribe from enterasys, send email to [email protected]<mailto:[email protected]> with the body: unsubscribe enterasys [email protected]<mailto:[email protected]> ________________________________ DISCLAIMER: This e-mail and any attachments to it may contain confidential and proprietary material and is solely for the use of the intended recipient. Any review, use, disclosure, distribution or copying of this transmittal is prohibited except by or on behalf of the intended recipient. If you have received this transmittal in error, please notify the sender and destroy this e-mail and any attachments and all copies, whether electronic or printed. --- To unsubscribe from enterasys, send email to [email protected] with the body: unsubscribe enterasys [email protected]
