Yes I do. I've tried two different crossover cables, each of which work in other physical connections.
At this point I'm wondering if it has something to do with 11.0 and the line cards. . . On Fri, Feb 20, 2009 at 10:55 AM, Wouter Prins <[email protected]> wrote: > Cat5E crosscable that is. :) > > 2009/2/20 Chuck Ufarley <[email protected]> > >> This might be a silly question, but I can't get a port to come up on a >> ServerIron. I enabled the interface and connected it properly to a >> FES-X2402 switch, but the J-B16GC and the J-B2Gx ports just won't come up >> and forward. The cards have worked in other configs, but I can't get >> anything to come out of "blocking" mode. Here are the shows (any help >> greatly appreciated): >> >> >> ServerIronGT E-1#sho run >> !Building configuration... >> !Current configuration : 378 bytes >> ! >> ver 11.0.00TD4 >> ! >> module 1 bi-0-port-wsm6-management-module >> module 3 bi-jc-2-port-gig-module >> module 4 bi-jc-16-port-gig-copper-module >> ! >> context default >> ! >> aaa authentication web-server default local >> no enable aaa console >> telnet server >> username admin password ..... >> snmp-server >> ! >> interface ethernet 4/9 >> ip address 192.168.0.77 255.255.255.0 >> ! >> end >> >> ServerIronGT E-1#sho run >> !Building configuration... >> !Current configuration : 378 bytes >> ! >> ver 11.0.00TD4 >> ! >> module 1 bi-0-port-wsm6-management-module >> module 3 bi-jc-2-port-gig-module >> module 4 bi-jc-16-port-gig-copper-module >> ! >> context default >> ! >> aaa authentication web-server default local >> no enable aaa console >> telnet server >> username admin password ..... >> snmp-server >> ! >> interface ethernet 4/9 >> ip address 192.168.0.77 255.255.255.0 >> ! >> end >> >> ServerIronGT E-1#sho mod >> Module Status Ports Starting MAC >> S1: B0GMR WSM6 Management Module, SYSIF 2 M6, ACTIV 0 >> S2: >> S3: J-BxG2 JetCore Gig Fiber Module, SYSIF OK 2 000c.dbb5.b640 >> S4: J-BxGC16 JetCore Gig Copper Module, SY OK 16 000c.dbb5.b660 >> ServerIronGT E-1#sho int e 4/9 >> GigabitEthernet4/9 is down, line protocol is down >> Hardware is GigabitEthernet, address is 000c.dbb5.b668 (bia >> 000c.dbb5.b668) >> Configured speed auto, actual unknown, configured duplex fdx, actual >> unknown >> Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING >> STP configured to ON, priority is level0, flow control enabled >> mirror disabled, monitor disabled >> Not member of any active trunks >> Not member of any configured trunks >> No port name >> Internet address is 192.168.0.77/24, MTU 1518 bytes, encapsulation >> ethernet >> 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization >> 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization >> 991 packets input, 77378 bytes, 0 no buffer >> Received 581 broadcasts, 410 multicasts, 0 unicasts >> 0 input errors, 0 CRC, 0 frame, 0 ignored >> 0 runts, 0 giants, DMA received 0 packets >> 0 packets output, 0 bytes, 0 underruns >> Transmitted 0 broadcasts, 0 multicasts, 0 unicasts >> 0 output errors, 0 collisions, DMA transmitted 0 packets >> ServerIronGT E-1# >> >> +++++ >> >> Thanks much, everyone. >> >> _______________________________________________ >> foundry-nsp mailing list >> [email protected] >> http://puck.nether.net/mailman/listinfo/foundry-nsp >> > >
_______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
