I've concluded there's just something wrong with the card. For some reason, it just causes the ports to enter a blocking state. Other cards and configs work. The same ports work without this card installed. Different cables work. The chassis/cards/cables work connected to any number of different switches and routers--just not with this management card.
I don't know why. Curse, maybe? In any case, I'm giving up on this WSM6-1, at least temporarily. Thanks everyone for your help. --Chuck On Mon, Feb 23, 2009 at 6:43 PM, sujith kumar <[email protected]> wrote: > Hi chuck, > Does the other ports in the same slot is working with 2402? Could you try > by connecting a laptop to the SI-GT to confirm your port is working or not? > Have you tried using an another patch cable? Probably it should be a port > failure since you have tested all the combination. > > -jith > > On Tue, Feb 24, 2009 at 4:30 AM, Chuck Ufarley <[email protected]>wrote: > >> Thanks, daniel-- >> >> But it's still blocking. Reloading the SI-GT, blocking. Trying "no >> span," blocking. Trying "enable," blocking. Strange. I can't figure out >> what's causing it. >> >> On Mon, Feb 23, 2009 at 10:59 AM, Daniel Kekai < >> [email protected]> wrote: >> >>> On the GT go to the interface config on 4/9 and type in: >>> >>> >>> >>> no spanning-tree >>> >>> >>> >>> Then test again >>> >>> >>> >>> -daniel >>> >>> >>> >>> *From:* Chuck Ufarley [mailto:[email protected]] >>> *Sent:* Friday, February 20, 2009 1:19 PM >>> >>> *To:* Daniel Kekai >>> *Cc:* [email protected] >>> *Subject:* Re: [f-nsp] Port state blocking? >>> >>> >>> >>> Thanks. At this point I'm just trying to get the ports to come up, so >>> it's the simplest config in the world. 2402 connected via port 26 to SI-GT >>> on port 4/9 with a crossover cable. It's 11.0 code, and it's worked in >>> other machines, though I don't have any currently running that code. >>> >>> 2402: >>> >>> FES2402 Switch#sho run >>> Current configuration: >>> ! >>> ver 04.0.00aTc1 >>> ! >>> ! >>> ! >>> ! >>> ! >>> ! >>> ! >>> ip address 192.168.0.64 255.255.255.0 >>> ! >>> ! >>> ! >>> ! >>> ! >>> ! >>> end >>> >>> FES2402 Switch#sho int e 26 >>> GigabitEthernet26 is up >>> Link Error Dampening is Disabled >>> Hardware is GigabitEthernet, address is 000c.db1d.4769 (bia >>> 000c.db1d.4769) >>> Configured speed 1Gbit, actual 1Gbit, configured duplex fdx, actual fdx >>> Configured mdi mode AUTO, actual MDI >>> Member of L2 VLAN ID 1, port is untagged, port state is FORWARDING >>> BPDU guard is Disabled, ROOT protect is Disabled >>> Link Error Dampening is Disabled >>> STP configured to ON, priority is level0 >>> Flow Control is config enabled, oper enabled, negotiation disabled >>> mirror disabled, monitor disabled >>> Not member of any active trunks >>> Not member of any configured trunks >>> No port name >>> IP MTU 1500 bytes >>> 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization >>> 300 second output rate: 640 bits/sec, 1 packets/sec, 0.00% utilization >>> 6461218 packets input, 423261535 bytes, 0 no buffer >>> Received 4282 broadcasts, 21834 multicasts, 6424644 unicasts >>> 0 input errors, 0 CRC, 0 frame, 0 ignored >>> 0 runts, 0 giants, DMA received 6461218 packets >>> 6746678 packets output, 1994941951 bytes, 0 underruns >>> Transmitted 189434 broadcasts, 124538 multicasts, 6432706 unicasts >>> 0 output errors, 0 collisions, DMA transmitted 6746678 packets >>> FES2402 Switch#sho int bri >>> >>> Port Link State Dupl Speed Trunk Tag Priori MAC Name >>> 1 Down None None None None No level0 000c.db1d.4750 >>> 2 Down None None None None No level0 000c.db1d.4751 >>> 3 Down None None None None No level0 000c.db1d.4752 >>> 4 Down None None None None No level0 000c.db1d.4753 >>> 5 Down None None None None No level0 000c.db1d.4754 >>> 6 Down None None None None No level0 000c.db1d.4755 >>> 7 Down None None None None No level0 000c.db1d.4756 >>> 8 Down None None None None No level0 000c.db1d.4757 >>> 9 Down None None None None No level0 000c.db1d.4758 >>> 10 Down None None None None No level0 000c.db1d.4759 >>> 11 Down None None None None No level0 000c.db1d.475a >>> 12 Down None None None None No level0 000c.db1d.475b >>> 13 Down None None None None No level0 000c.db1d.475c >>> 14 Down None None None None No level0 000c.db1d.475d >>> 15 Down None None None None No level0 000c.db1d.475e >>> 16 Down None None None None No level0 000c.db1d.475f >>> 17 Down None None None None No level0 000c.db1d.4760 >>> 18 Down None None None None No level0 000c.db1d.4761 >>> 19 Down None None None None No level0 000c.db1d.4762 >>> 20 Down None None None None No level0 000c.db1d.4763 >>> 21 Down None None None None No level0 000c.db1d.4764 >>> 22 Down None None None None No level0 000c.db1d.4765 >>> 23 Up Forward Full 100M None No level0 000c.db1d.4766 >>> 24 Up Forward Full 100M None No level0 000c.db1d.4767 >>> 25 Up Forward Full 1G None No level0 000c.db1d.4768 >>> 26 Up Forward Full 1G None No level0 000c.db1d.4769 >>> FES2402 Switch# >>> >>> SI-GT: >>> >>> ServerIronGT E-1#sho run >>> !Building configuration... >>> !Current configuration : 378 bytes >>> ! >>> ver 11.0.00TD4 >>> ! >>> module 1 bi-0-port-wsm6-management-module >>> module 3 bi-jc-2-port-gig-module >>> module 4 bi-jc-16-port-gig-copper-module >>> ! >>> context default >>> ! >>> aaa authentication web-server default local >>> no enable aaa console >>> telnet server >>> username admin password ..... >>> snmp-server >>> ! >>> interface ethernet 4/9 >>> ip address 192.168.0.77 255.255.255.0 >>> ! >>> end >>> >>> ServerIronGT E-1#sho int e 4/9 >>> GigabitEthernet4/9 is down, line protocol is down >>> Hardware is GigabitEthernet, address is 000c.dbb5.b668 (bia >>> 000c.dbb5.b668) >>> Configured speed auto, actual unknown, configured duplex fdx, actual >>> unknown >>> Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING >>> STP configured to ON, priority is level0, flow control enabled >>> mirror disabled, monitor disabled >>> Not member of any active trunks >>> Not member of any configured trunks >>> No port name >>> Internet address is 192.168.0.77/24, MTU 1518 bytes, encapsulation >>> ethernet >>> 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization >>> 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization >>> 6096 packets input, 507641 bytes, 0 no buffer >>> Received 4256 broadcasts, 1838 multicasts, 2 unicasts >>> 0 input errors, 0 CRC, 0 frame, 0 ignored >>> 0 runts, 0 giants, DMA received 0 packets >>> 0 packets output, 0 bytes, 0 underruns >>> Transmitted 0 broadcasts, 0 multicasts, 0 unicasts >>> 0 output errors, 0 collisions, DMA transmitted 0 packets >>> ServerIronGT E-1#sho int bri >>> >>> Port Link State Dupl Speed Trunk Tag Priori MAC Name >>> 4/1 Down None None None None No level0 000c.dbb5.b660 >>> 4/2 Down None None None None No level0 000c.dbb5.b661 >>> 4/3 Down None None None None No level0 000c.dbb5.b662 >>> 4/4 Down None None None None No level0 000c.dbb5.b663 >>> 4/5 Down None None None None No level0 000c.dbb5.b664 >>> 4/6 Down None None None None No level0 000c.dbb5.b665 >>> 4/7 Down None None None None No level0 000c.dbb5.b666 >>> 4/8 Down None None None None No level0 000c.dbb5.b667 >>> 4/9 Down None None None None No level0 000c.dbb5.b668 >>> 4/10 Down None None None None No level0 000c.dbb5.b669 >>> 4/11 Down None None None None No level0 000c.dbb5.b66a >>> 4/12 Down None None None None No level0 000c.dbb5.b66b >>> 4/13 Down None None None None No level0 000c.dbb5.b66c >>> 4/14 Down None None None None No level0 000c.dbb5.b66d >>> 4/15 Down None None None None No level0 000c.dbb5.b66e >>> 4/16 Down None None None None No level0 000c.dbb5.b66f >>> ServerIronGT E-1# >>> >>> On Fri, Feb 20, 2009 at 12:06 PM, Daniel Kekai < >>> [email protected]> wrote: >>> >>> Send the output on the FES side interface and if possible the configs for >>> both the GT and FES >>> >>> Also do you have this setup working with other GT's – FES? If so are you >>> running the same code? >>> >>> >>> >>> -D >>> >>> >>> >>> *From:* Chuck Ufarley [mailto:[email protected]] >>> *Sent:* Friday, February 20, 2009 11:17 AM >>> *To:* Daniel Kekai >>> *Cc:* [email protected] >>> *Subject:* Re: [f-nsp] Port state blocking? >>> >>> >>> >>> It seems to be disabled. Should I enable it? This hasn't been an issue >>> in past configs. >>> >>> ServerIronGT E-1#sho span >>> >>> Spanning-tree is not configured on port-vlan 1. >>> >>> Thanks again. >>> >>> On Fri, Feb 20, 2009 at 11:01 AM, Daniel Kekai < >>> [email protected]> wrote: >>> >>> Check your spanning tree >>> >>> -D >>> >>> >>> >>> *From:* [email protected] [mailto: >>> [email protected]] *On Behalf Of *Chuck Ufarley >>> *Sent:* Friday, February 20, 2009 9:51 AM >>> *To:* [email protected] >>> *Subject:* [f-nsp] Port state blocking? >>> >>> >>> >>> This might be a silly question, but I can't get a port to come up on a >>> ServerIron. I enabled the interface and connected it properly to a >>> FES-X2402 switch, but the J-B16GC and the J-B2Gx ports just won't come up >>> and forward. The cards have worked in other configs, but I can't get >>> anything to come out of "blocking" mode. Here are the shows (any help >>> greatly appreciated): >>> >>> ServerIronGT E-1#sho run >>> !Building configuration... >>> !Current configuration : 378 bytes >>> ! >>> ver 11.0.00TD4 >>> ! >>> module 1 bi-0-port-wsm6-management-module >>> module 3 bi-jc-2-port-gig-module >>> module 4 bi-jc-16-port-gig-copper-module >>> ! >>> context default >>> ! >>> aaa authentication web-server default local >>> no enable aaa console >>> telnet server >>> username admin password ..... >>> snmp-server >>> ! >>> interface ethernet 4/9 >>> ip address 192.168.0.77 255.255.255.0 >>> ! >>> end >>> >>> ServerIronGT E-1#sho run >>> !Building configuration... >>> !Current configuration : 378 bytes >>> ! >>> ver 11.0.00TD4 >>> ! >>> module 1 bi-0-port-wsm6-management-module >>> module 3 bi-jc-2-port-gig-module >>> module 4 bi-jc-16-port-gig-copper-module >>> ! >>> context default >>> ! >>> aaa authentication web-server default local >>> no enable aaa console >>> telnet server >>> username admin password ..... >>> snmp-server >>> ! >>> interface ethernet 4/9 >>> ip address 192.168.0.77 255.255.255.0 >>> ! >>> end >>> >>> ServerIronGT E-1#sho mod >>> Module Status Ports Starting MAC >>> S1: B0GMR WSM6 Management Module, SYSIF 2 M6, ACTIV 0 >>> S2: >>> S3: J-BxG2 JetCore Gig Fiber Module, SYSIF OK 2 000c.dbb5.b640 >>> S4: J-BxGC16 JetCore Gig Copper Module, SY OK 16 000c.dbb5.b660 >>> ServerIronGT E-1#sho int e 4/9 >>> GigabitEthernet4/9 is down, line protocol is down >>> Hardware is GigabitEthernet, address is 000c.dbb5.b668 (bia >>> 000c.dbb5.b668) >>> Configured speed auto, actual unknown, configured duplex fdx, actual >>> unknown >>> Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING >>> STP configured to ON, priority is level0, flow control enabled >>> mirror disabled, monitor disabled >>> Not member of any active trunks >>> Not member of any configured trunks >>> No port name >>> Internet address is 192.168.0.77/24, MTU 1518 bytes, encapsulation >>> ethernet >>> 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization >>> 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization >>> 991 packets input, 77378 bytes, 0 no buffer >>> Received 581 broadcasts, 410 multicasts, 0 unicasts >>> 0 input errors, 0 CRC, 0 frame, 0 ignored >>> 0 runts, 0 giants, DMA received 0 packets >>> 0 packets output, 0 bytes, 0 underruns >>> Transmitted 0 broadcasts, 0 multicasts, 0 unicasts >>> 0 output errors, 0 collisions, DMA transmitted 0 packets >>> ServerIronGT E-1# >>> >>> +++++ >>> >>> Thanks much, everyone. >>> >>> >>> >>> >>> >> >> >> _______________________________________________ >> foundry-nsp mailing list >> [email protected] >> http://puck.nether.net/mailman/listinfo/foundry-nsp >> > > > > -- > -Sujith >
_______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
