ok, it normally does this if it can't find a suitable ssid to associate to.
Are you sure the AP is setup to accept WPA-PSK?
-a
On 25 January 2015 at 09:56, Kostya Berger <berger...@yahoo.co.uk> wrote:
> It only keeps repeating this:
> <3>CTRL-EVENT-SCAN-RESULTS
> <3>WPS-AP-AVAILABLE-PIN
> <3>CTRL-EVENT-SCAN-RESULTS
> <3>WPS-AP-AVAILABLE-PIN
> .......
> when I ask for 'status' it says:
> wpa_state=SCANNING
> address=60:6c:66:4d:28:a3
>
> With kindest regards,
> Kostya Berger
>
>
>
> On Sunday, 25 January 2015, 19:46, Adrian Chadd <adr...@freebsd.org> wrote:
>
>
>
> Ok, need to see if it's trying to associate>
>
> in wpa_cli, do:
>
> log_level debug
>
> Or, run it like this
>
> wpa_supplicant -i wlan0 -d -d -d -v -c /etc/wpa_supplicant.conf
>
> (making sure no other supplicant is running)
>
>
> -a
>
>
> On 25 January 2015 at 09:16, Kostya Berger <berger...@yahoo.co.uk> wrote:
>> Hi Adrian,
>>
>> no, it shows only iwn0 as "associated". Here is `ifconfig wlan0` output:
>>
>> wlan0: flags=8c43<UP,BROADCAST,RUNNING,OACTIVE,SIMPLEX,MULTICAST> metric 0
>> mtu 1500
>> ether 60:6c:66:4d:28:a3
>> inet6 fe80::626c:66ff:fe4d:28a3%wlan0 prefixlen 64 scopeid 0x5
>> nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
>> media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
>> status: no carrier
>> ssid "" channel 12 (2467 MHz 11g)
>> country US authmode WPA1+WPA2/802.11i privacy MIXED deftxkey UNDEF
>> txpower 15 bmiss 10 scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250
>> roam:rssi 7 roam:rate 5 protmode CTS wme roaming MANUAL bintval 0
>>
>>
>> With kindest regards,
>> Kostya Berger
>>
>>
>>
>> On Sunday, 25 January 2015, 18:44, Adrian Chadd <adr...@freebsd.org>
>> wrote:
>>
>>
>>
>> Hi,
>>
>> Does ifconfig wlan0 list it as associated?
>>
>>
>>
>> -a
>>
>>
>> On 24 January 2015 at 19:07, Kostya Berger <berger...@yahoo.co.uk> wrote:
>>> Here's my ifconfig output:
>>> wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu
>>> 1500
>>> ether 60:6c:66:4d:28:a3
>>> inet6 fe80::626c:66ff:fe4d:28a3%wlan0 prefixlen 64 scopeid 0x5
>>> nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
>>> media: IEEE 802.11 Wireless Ethernet autoselect (autoselect)
>>> status: no carrier
>>> ssid "" channel 12 (2467 MHz 11g)
>>> country US authmode WPA1+WPA2/802.11i privacy MIXED deftxkey UNDEF
>>> txpower 15 bmiss 10 scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250
>>> roam:rssi 7 roam:rate 5 protmode CTS wme roaming MANUAL bintval 0
>>>
>>> So dhclient starts with the words "no link" and soon gives up. At that,
>>> ifconfig wlan0 list scan returnes full list of available WiFi
>>> networks.Here
>>> is my wpa_supplicant.conf (pretty generic):
>>> ctrl_interface=/var/run/wpa_supplicant
>>> ctrl_interface_group=wheel
>>>
>>> network={
>>> ssid="MyHOME-NET"
>>> scan_ssid=1
>>> key_mgmt=WPA-PSK
>>> psk="my passphrase"
>>> }
>>>
>>> and here my /var/log/messages part to the point (not much):
>>> Jan 25 05:49:45 kostya-home kernel: wlan0:
>>> Jan 25 05:49:45 kostya-home kernel: Ethernet address: 60:6c:66:4d:28:a3
>>> Jan 25 05:49:45 kostya-home devd: Executing '/etc/pccard_ether wlan0
>>> start'
>>> Jan 25 05:49:45 kostya-home wpa_supplicant[83148]: Successfully
>>> initialized wpa_supplicant
>>> Jan 25 05:49:45 kostya-home kernel: iwn0: iwn_read_firmware: ucode
>>> rev=0x12a80601
>>> Jan 25 05:49:56 kostya-home root: /etc/rc.d/dhclient: WARNING: failed to
>>> start dhclient With kindest regards,
>>> Kostya Berger
>>>
>>>
>>>
>>> On Saturday, 24 January 2015, 1:51, Kostya Berger
>>> <berger...@yahoo.co.uk> wrote:
>>>
>>>
>>>
>>> Hello everyone,
>>> glad to meet you. I subscribed to this list in order to get my above
>>> mentioned card to work.Currently, the situation is as follows:It's Intel
>>> Centrino wireless-N 2230 Mini PCIe that came pre-installed on my
>>> GA-Z77N-wifi motherboard.I'm running 11.0-CURRENT, downloaded
>>> pre-compiled
>>> txz distro files, dated 22.01.2015.
>>> iwn0 interface gets created (in 10.1-RELEASE it doesn't), also wlan0
>>> interface gets created all right.ifconfig wlan0 list scan command returns
>>> the list of the available SSIDs with parameters.However, wpa_supplicant
>>> fails to connect to my router's SSID, though it is present among the scan
>>> results.ifconfig wlan0 shows, among other things, "no carrier" for wlan0.
>>> Manual connection using wpa_cli is no better.
>>> BTW, can I somehow apply the needed code to 10.1-STABLE source tree and
>>> compile there, or do I need 11-CURRENT to run the latest version of this
>>> driver? Because 11-CURRENT will require rebuilding all ports. So right
>>> now
>>> I'm running it on a separate spare HDD, only base system.
>>> Thanks to everyone for your hard work :)))
>>> With kindest regards,
>>> Kostya Berger
>>
>>>
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>> freebsd-wireless@freebsd.org mailing list
>>> http://lists.freebsd.org/mailman/listinfo/freebsd-wireless
>>> To unsubscribe, send any mail to
>>> "freebsd-wireless-unsubscr...@freebsd.org
>> "
>>
>>
>
>
_______________________________________________
freebsd-wireless@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-wireless
To unsubscribe, send any mail to "freebsd-wireless-unsubscr...@freebsd.org"
