I feel like I've wet my pants in front of 2 million people.... ____________________________ Jim Hughes 603-271-5586 "There's no sense in being precise when you don't even know what you're talking about." John von Neumann
=>-----Original Message----- =>From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On =>Behalf Of Bill Munson =>Sent: Friday, July 20, 2007 2:59 PM =>To: [email protected] =>Subject: Re: ZVM 5.3 - Z890 - Second Level Install => =>NO NO it is a virtual console =>from your userid enter q cons =>like this => =>q cons =>CONS 0009 ON LDEV L0004 TERM START HOST TCPIP FROM 10.37.60.218 => 0009 CL A CONT NOHOLD COPY 001 READY FORM STD4 => 0009 TO OTSMUNS PRT DIST 6059 FLASHC 000 DEST OFF => 0009 FLASH CHAR MDFY 0 FCB LPP OFF => 0009 3215 NOEOF OPEN 2730 NOKEEP NOMSG NONAME => 0009 SUBCHANNEL = 0004 => =>your cons sole is 0009 => =>good luck => =>Bill Munson =>VM System Programmer =>Office of Information Technology =>State of New Jersey =>(609) 984-4065 => =>President MVMUA =>http://www.marist.edu/~mvmua => => => =>Hughes, Jim - OIT wrote: =>> The console address when I was using the OSA TN3270 was 0090. The =>> console address when using ZVM 5.2 TN3270 is L00C3. I guess Ill try =>> L00C3 and see what happens. =>> =>> =>> =>> Thanks. =>> =>> =>> =>> ____________________________ =>> Jim Hughes =>> 603-271-5586 =>> "There's no sense in being precise when you don't even know what you're =>> talking about." =>> John von Neumann =>> =>> ------------------------------------------------------------------------ =>> =>> *From:* The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] =>> *On Behalf Of *David Kreuter =>> *Sent:* Friday, July 20, 2007 2:44 PM =>> *To:* [email protected] =>> *Subject:* Re: ZVM 5.3 - Z890 - Second Level Install =>> =>> =>> =>> Is 00C3 your console address? Are you sure? =>> David =>> =>> =>> -----Original Message----- =>> From: The IBM z/VM Operating System on behalf of Hughes, Jim - OIT =>> Sent: Fri 7/20/2007 2:37 PM =>> To: [email protected] =>> Subject: [IBMVM] ZVM 5.3 - Z890 - Second Level Install =>> =>> I am stumped. =>> =>> I have loaded the 530RES volume and trying to IPL. =>> =>> My virtual machine is defined as 64M, class BG, Machine XA. I did the =>> terminal commode 3270. I did the system reset. =>> =>> I did the IPL 1002 CLEAR LOADPARM 00C3. =>> =>> I did not receive the SAL screen. It jumped past it and is now asking =>> for input. The messge "H HCPSED6013A A CP read is pending." Is on the =>> screen. =>> =>> The state is "RUNNING". I type COLD DRAIN NOAUTOLOG and press the Enter =>> key. Its been a couple of hours with no movement. =>> =>> I've done this a few times with identical results. =>> =>> Two times my emulator session was connected via the OSA TN3270 service. =>> Then I logged in using the ZVM 5.2 TN3270 service and the results are =>> identical. =>> =>> What am I doing wrong? I am no getting the SAL screen. And it acts as if =>> my response to COLD DRAIN NOAUTOLOG is not going anywhere. =>> =>> EXPLORE/VM is showing no dasd activity for any of my ZVM53 volumes. =>> =>> What a way to end the week.....<sigh> =>> =>> ____________________________ =>> Jim Hughes =>> 603-271-5586 =>> "There's no sense in being precise when you don't even know what you're =>> talking about." =>> John von Neumann =>>
