congratz...lol..then it's confirmed as a V1.1 bug...my bad actually for forgetting to add the line with the value "1" to each device id...silly me..
that line is kinda improtant to GMA core as it actually consist of 2 device simultaneously...so the 2nd line is for the 2nd "virtual" device (which are important for double display and stuffs) to work...so far i didnt received any complain becoz most of us here use 945GM and not GME..that sums it up then..im gonna make an update on V1.1 "if" MAD_BEAST approve it...i guess V1.1 will finally support netbooks afterall....a very much Thanks telling me this bug Tribaljet!! ^^ the CP are meant to be user friendly....it's not possible of unclean registry...V1.1 installer are designed to be clean as possible... -1st, the installer cleans the registry from old drivers (new and old versions of MD) EXCEPT the addgame registry values which are kept for gaming purposes.. - after that only when the registry are clean. the installer install all the necessary file for the V1.1 to work flawlessly.. - mind that the installer also saves the important user's setting such as native resolution, openGL setting and etc on a temp file, after the installation, that temp file will fuse with the main registry as the final step before reboot.. hmm,about the HDD WEI rating.. im not sure about that but MSI compatible driver can effect all mobo IO in general..since GMA950 is PCI...thus it will effect other bus IO, including HDD in my theory...commonly all thing that connects to the mobo are connected to each other, im guessing that sums it up... finally, thanks for supporting V1.1 drivers ^^ On Fri, Jun 11, 2010 at 1:53 PM, tribaljet <[email protected]> wrote: > And so far shaders are going strong without any hiccups on media > player classic :) > > On Jun 11, 6:20 am, tribaljet <[email protected]> wrote: > > Seriously, someone give Angelic a big round of applauses... or at > > least a 1 year supply of pizza rolls. Right now I'm typing on a > > spanking new V1.1 install which on a few directdraw tests performs > > better than sigma 3.1. Still have to test direct3d, but for now things > > seem good. > > Out of curiosity, what significant changes were made when installing > > the driver through this alternate way? And there's this thing that > > bothers me, after uninstalling the previous driver and installing V1.1 > > all my CP settings were saved, perhaps due to me not cleaning the reg > > after uninstalling the previous drivers. > > > > Oh, the oddest thing happened with your drivers, and I say it was your > > drivers because I haven't changed anything, neither software nor > > hardware. My hdd rating on the wei went from 5.0 to 5.7! And I know > > wei sometimes changes its values, from what I heard, but it never > > happened to me in vista or 7. > > > > On Jun 11, 5:12 am, AngelicTears <[email protected]> wrote: > > > > > hmm, that's kinda odd since no one ever reported the problem before..i > > > assume u know how to edit inf file... > > > open the driver folder where u extracted it...find the graphics folder > and > > > open the igdlh.inf.. > > > > > in the file fine the "intel.mfg" section where the device id are > listed..u > > > can use find in note pad... > > > the u can find this line : > > > > > %iBWGX0% = i965GX0, PCI\VEN_8086&DEV_27AE > > > > > make a space under the line and paste this line. > > > > > %iBWGX1% = i965GX1, PCI\VEN_8086&DEV_27AE > > > > > save the inf file and run installation normally... > > > > > On Fri, Jun 11, 2010 at 11:08 AM, tribaljet <[email protected]> > wrote: > > > > Well, I uninstalled, rebooted and installed the drivers. Right where > > > > it says to press next to continue the screen immediately began > lagging > > > > and aero going back and forth with basic. Didn't even have the chance > > > > to reboot. So, neither installing on safe mode nor in a normal > session > > > > seem to work. What can be causing this? > > > > > > -- > > > > 9xx SOLDIERS SANS FRONTIERS > > > > > > -- > 9xx SOLDIERS SANS FRONTIERS > -- 9xx SOLDIERS SANS FRONTIERS
