Hy, second try, this time more information got the following Hardware: - Asus K8V (most recent BIOS) - AMD Sempron 2600+ (S754) (Palermo) - 2x512MB DDR33 RAM - Haupaug PVR150
and this Hardware: - Gentoo Linux ~x86 - Kernel: Linux theather 2.6.16-gentoo-r7 #3 PREEMPT Sun May 14 23:25:20 CEST 2006 i686 AMD Sempron(tm) Processor 2800+ GNU/Linux - IVTV: Version 0.4.2 from Gentoo-Package I installed ivtv via emerge. dmesg: ivtv: ==================== START INIT IVTV ==================== ivtv: version 0.4.2 (tagged release) loading ivtv: Linux version: 2.6.16-gentoo-r7 preempt K8 gcc-3.4 ivtv: In case of problems please include the debug info between ivtv: the START INIT IVTV and END INIT IVTV lines, along with ivtv: any module options, when mailing the ivtv-users mailinglist. ivtv0: Autodetected WinTV PVR 150 card (cx23416 based) ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50] tveeprom 0-0050: Hauppauge model 26034, rev C197, serial# 2997674 tveeprom 0-0050: tuner model is TCL 2002MB_3H (idx 97, type 55) tveeprom 0-0050: TV standards PAL(B/G) PAL(D/D1/K) (eeprom 0x44) tveeprom 0-0050: audio processor is CX25842 (idx 36) tveeprom 0-0050: decoder processor is CX25842 (idx 29) tveeprom 0-0050: has no radio, has IR remote tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61] cx25840 0-0044: cx25842-23 found @ 0x88 (ivtv i2c driver #0) cx25840 0-0044: loaded v4l-cx25840.fw firmware (14264 bytes) ivtv0: i2c attach to card #0 ok [client=cx25840, addr=44] wm8775 0-001b: chip found @ 0x36 (ivtv i2c driver #0) ivtv0: i2c attach to card #0 ok [client=wm8775, addr=1b] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes) ivtv0: Encoder revision: 0x02050032 ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total) ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total) ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total) cx25840 0-0044: 0x0000 is not a valid video input! tuner 0-0061: tuner type not set tuner 0-0061: tuner type not set ivtv0: Initialized WinTV PVR 150, card #0 ivtv: ==================== END INIT IVTV ==================== My "ivtvctl -a" gives: ==== ioctl IVTV_IOC_G_CODEC ok Codec parameters aspect : 2 audio : 0x00e9 bframes : 3 bitrate_mode: 0 bitrate : 8000000 bitrate_peak: 9600000 dnr_mode : 0 dnr_spatial : 0 dnr_temporal: 8 dnr_type : 0 framerate : 0 framespergop: 12 gop_closure : 1 pulldown : 0 stream_type : 14 ioctl VIDIOC_G_FMT ok Type : Video Capture Width : 720 Height : 576 ioctl VIDIOC_QUERYCAP ok Driver name : ivtv Card type : WinTV PVR 150 Bus info : 0000:00:0d.0 Driver version: 1026 Capabilities : 0x01030051 ioctl: VIDIOC_ENUMINPUT Input : 0 Name : Tuner Type : 0x00000001 Audioset: 0x00000003 Tuner : 0x00000000 Standard: 0x00000000000000FF ( PAL ) Status : 0 Input : 1 Name : Composite 0 Type : 0x00000002 Audioset: 0x00000003 Tuner : 0x00000000 Standard: 0x00000000007F7FFF ( PAL NTSC SECAM ) Status : 0 Input : 2 Name : Composite 1 Type : 0x00000002 Audioset: 0x00000003 Tuner : 0x00000000 Standard: 0x00000000007F7FFF ( PAL NTSC SECAM ) Status : 0 Input : 3 Name : S-Video 0 Type : 0x00000002 Audioset: 0x00000003 Tuner : 0x00000000 Standard: 0x00000000007F7FFF ( PAL NTSC SECAM ) Status : 0 Input : 4 Name : S-Video 1 Type : 0x00000002 Audioset: 0x00000003 Tuner : 0x00000000 Standard: 0x00000000007F7FFF ( PAL NTSC SECAM ) Status : 0 ioctl VIDIOC_G_INPUT ok Video input = 3 ioctl: VIDIOC_ENUMOUTPUT ioctl VIDIOC_G_OUTPUT failed: Invalid argument ioctl: VIDIOC_ENUMAUDIO Input : 0 Name : Tuner Audio In Input : 1 Name : Audio Line 1 Input : 2 Name : Audio Line 2 Input : 3 Name : Audio Line 3 Input : 4 Name : Audio Line 4 ioctl VIDIOC_G_AUDIO ok Audio input = 2: Audio Line 2 ioctl VIDIOC_G_FREQUENCY ok Frequency = 6400 ioctl: VIDIOC_ENUMSTD index : 0 ID : 0x0000000000003000 Name : NTSC Frame period: 1001/30000 Frame lines : 525 index : 1 ID : 0x00000000000000FF Name : PAL Frame period: 1/25 Frame lines : 625 index : 2 ID : 0x00000000007F0000 Name : SECAM Frame period: 1/25 Frame lines : 625 ioctl VIDIOC_G_STD ok Video standard = 0x000000ff ioctl: VIDIOC_QUERYCTRL Brightness = 128 Contrast = 64 Saturation = 64 Hue = 0 Volume = 60928 Mute = 1 ==== The Problem is: I cant get any audio-data from my pvr. The Problem seems the "Mute = 1" at the end. In the wiki I read that this is perhaps a firmware-error. So I tried different ones: 1. The recommended from the wiki 2. The most recent from Haupauge 3. This: http://hauppauge.lightpath.net/software/pvr150/pvr150_inf.zip All of the gave the same error, I was never able to change the mute-status. A "ivtvctl --set-ctrl=mute=0" didnt show any effect. I can record a mpeg file via "cat /dev/video0 >> /mnt/test.mpeg", but it contains no audio data (but a audio stream). So the card is basicaly working, its only an audio issue. Im not sure why a 0.4 driver works with my 2.6.16-kernel, but it does, at least for the video. Another question is: For the 0.6-versions, is the message in the kernel-log showing the right version? I tried to install a 0.6-version and it still showed version 0.4 in the kernel-log. Who can help me? Without a sound, a TV-Device is useless :D Thanks a lot Dominik _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
