On 6/19/07, Josh White <[EMAIL PROTECTED]> wrote: > I have a PVR-250 that I bought in the fall of 2002. I recently started > trying to setup MythTV on an Ubuntu Feisty Fawn box with the intention of > using this card. I haven't used the card in years, so I'm not 100% sure the > hardware works. When I try to test the card with VLC or "cat /dev/video0 > > /media/disk/store/Media/Video/Recordings/test.mpg" all I > get is static. There is no sound on the test recordings either. I > downloaded the firmware from the Ubuntu repositories and installed it with > synaptic package manager, but that didnt seem to change anything. When I > try changing the channels (I'm using standard analog cable as the source) I > can get slight variations in the static I see, but other than that, I see no > change. I believe the firmware version is .2007217.
Open a terminal and type: tail -f /var/log/messages (or point it to where your distro puts the kernel messages). Now open another terminal and try to change to a channel. Check if you see any error messages in the first terminal. The init below looks ok. Which program are you using to tune, ivtv-tune? Greets Sander > [EMAIL PROTECTED]:/media/disk/store/Media/Video/Recordings# > dmesg |grep Initialized[ 34.185184] ivtv0: Initialized Hauppauge WinTV > PVR-250, card #0 > [EMAIL PROTECTED]:/media/disk/store/Media/Video/Recordings# > dmesg | tac | sed -n '/=\ \ END INIT IVTV\ \ =/,/= START INIT IVTV =/p;/= > START INIT IVTV =/q' | tac > [ 32.305558] ivtv: ==================== START INIT IVTV > ==================== > [ 32.305563] ivtv: version 0.10.1 (tagged release) loading > [ 32.305565] ivtv: Linux version: 2.6.20-16-generic SMP mod_unload 586 > [ 32.305567] ivtv: In case of problems please include the debug info > between > [ 32.305569] ivtv: the START INIT IVTV and END INIT IVTV lines, along > with > [ 32.305571] ivtv: any module options, when mailing the ivtv-users > mailinglist. > [ 32.305678] ivtv0: Autodetected Hauppauge card (cx23415 based) > [ 32.305734] ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 17 (level, low) -> > IRQ 20 > [ 32.322730] usbcore: registered new interface driver libusual > [ 33.041592] ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes) > [ 33.137892] ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) > [ 33.360552] ivtv0: Encoder revision: 0x02060039 > [ 33.368531 ] ivtv0: Decoder revision: 0x02020023 > [ 33.439574] tveeprom 0-0050: Hauppauge model 48012, rev G310, serial# > 2600481 > [ 33.439579] tveeprom 0-0050: tuner model is Philips FI1236 MK2 (idx 10, > type 2) > [ 33.439582 ] tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08) > [ 33.439584] tveeprom 0-0050: audio processor is MSP3445 (idx 12) > [ 33.439586] tveeprom 0-0050: has radio > [ 33.439589] ivtv0: Autodetected Hauppauge WinTV PVR-250 > [ 33.467337] tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0) > [ 33.552178] saa7115 0-0021: saa7115 found (1f7115d0e100000) @ 0x42 (ivtv > i2c driver #0) > [ 33.763020] msp3400 0-0040: MSP3445G-B8 found @ 0x80 (ivtv i2c driver #0) > [ 33.763024] msp3400 0-0040: MSP3445G-B8 supports radio, mode is > autodetect and autoselect > [ 33.764738] ivtv0: Registered device video0 for encoder MPEG (4 MB) > [ 33.764954] ivtv0: Registered device video32 for encoder YUV (2 MB) > [ 33.765196] ivtv0: Registered device vbi0 for encoder VBI (1 MB) > [ 33.765298] ivtv0: Registered device video24 for encoder PCM audio (1 MB) > [ 33.765559] ivtv0: Registered device radio0 for encoder radio > [ 33.765581] tuner 0-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and > compatibles)) > [ 34.185184] ivtv0: Initialized Hauppauge WinTV PVR-250, card #0 > [ 34.185206] ivtv: ==================== END INIT IVTV > ==================== _______________________________________________ ivtv-users mailing list [email protected] http://ivtvdriver.org/mailman/listinfo/ivtv-users
