Hi Evan, Downloaded, installed it and it work for my PIC16F18857 (also programmed a PIC 12F675 and works OK).
I still get the error on the PIC16F18857 that it is not able to program address 0x0000 (verification error) but I think the PIC died so not related to the PICKit3 software. I will try with a fresh version. Thanks for the quick service. Kind regards, Rob ________________________________ Van: '[email protected]' via jallib <[email protected]> Verzonden: vrijdag 11 november 2022 19:10 Aan: jallib <[email protected]> Onderwerp: Re: [jallib] Re: PICKIT 3 problems Just sent the order go through the process. If you have issues, then, we can set about resolving for you and the greater community. The new release has the new 16F180xx and 16F171xx chipfamily - we are waiting on the 16F181xx to arrive before we can add (as we have to test them!). Also, adding more PIC32Mxs at the moment. Always busy. On Friday, 11 November 2022 at 17:59:56 UTC [email protected] wrote: Hi Evan, I noticed indeed issues with PICkitminus that it sometimes recognizes another PIC than the one that is installed. So in order to get rid of this - and other issues I encountered - I just ordered your PICKitPlus software for my PICKit3 🙂. Kind regards, Rob ________________________________ Van: '[email protected]' via jallib <[email protected]> Verzonden: vrijdag 11 november 2022 07:51 Aan: jallib <[email protected]> Onderwerp: [jallib] Re: PICKIT 3 problems As the real developer of PICKitPlus and the database that was plagiarized by PK- I am the right person to help. When our database was copied the developer decided to change the order that the chip families are searched. I wrote a detailed analysis for him and he ignored. So, using PK- can apply the incorrect voltage your PCB during startup. Which chip or chips have this issue? This will help me isolate the issue. Evan On Friday, 11 November 2022 at 06:43:29 UTC hans wrote: Hello all, I regularly have problems with the pickit-3.(MPlab X IPE v 5.45) . Because it happens less often when I first start up my PC, connect the pickit to the PIC and put voltage on it and only then connect the USB cable, this is my base. Despite this, I get often messages that the voltage is insufficient, the PIC is not the right type or a wrong feedback occurs during programming. This can almost always be solved by restarting MPlab, or by first performing a read or an erase. Lately I've been working with 3.3V. Now I had a program under 3.3V and that didn't work at all after programming without errors. After I erased the PIC separately below 5 V, the program works again. I have two clones. One suddenly doesn't work at all under 3.3 V, but with the Pickit_minus (with modified firmware) on 5V. Can anyone tell me where to look for the cause of all this? regards Hans -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/e74098b6-6d7d-45a6-ba6c-087cc51faadcn%40googlegroups.com<https://groups.google.com/d/msgid/jallib/e74098b6-6d7d-45a6-ba6c-087cc51faadcn%40googlegroups.com?utm_medium=email&utm_source=footer>. -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]<mailto:[email protected]>. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/64b27e61-12c7-451c-85e4-5c743cb3b417n%40googlegroups.com<https://groups.google.com/d/msgid/jallib/64b27e61-12c7-451c-85e4-5c743cb3b417n%40googlegroups.com?utm_medium=email&utm_source=footer>. -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/GVXP195MB16375063A36BD0B02383E0C0E6009%40GVXP195MB1637.EURP195.PROD.OUTLOOK.COM.
