These issues are typically very simple to resolve. I have test rigs that cover about 1300 PICs and therefore we can replicate issues very quickly.
We can always help to verify an issue. :-) On Saturday, 12 November 2022 at 07:07:28 UTC hans wrote: > I had the same annoying problems with an 18F4520. Sometimes yes, sometimes > not, then again a non-working program !! > Luckily I still have my old wisp. Connected and everything works > flawlessly, just like before > . If something didn't work for me in the past, I was sure it was my fault. > !!! > Wouldn't Wouter be able to expand his wisp so that it can also handle the > newer things? > Otherwise I think I'll just use pics that the wisp supports. There's > plenty of fun to do with that. > > Op zaterdag 12 november 2022 om 07:06:16 UTC+1 schreef vasile: > >> Rob, prior to throwing it away, plug it in a stanium foil for a while to >> short all pins together. >> Old PIC12F675 had this problem with address 0 and this was in a >> surprising way the cure. >> >> Of course, only if you did not supply it at 220V, see the top right >> corner... >> http://www.voti.nl/wloader/index_1.html >> another one of my daughter's old drawings...:) >> >> >> On Fri, Nov 11, 2022 at 9:53 PM Rob CJ <[email protected]> wrote: >> >>> Hi Evan, >>> >>> Downloaded, installed it and it work for my PIC16F18857 (also programmed >>> a PIC 12F675 and works OK). >>> >>> I still get the error on the PIC16F18857 that it is not able to program >>> address 0x0000 (verification error) but I think the PIC died so not related >>> to the PICKit3 software. I will try with a fresh version. >>> >>> Thanks for the quick service. >>> >>> Kind regards, >>> >>> Rob >>> >>> ------------------------------ >>> *Van:* '[email protected]' via jallib <[email protected]> >>> *Verzonden:* vrijdag 11 november 2022 19:10 >>> *Aan:* jallib <[email protected]> >>> *Onderwerp:* Re: [jallib] Re: PICKIT 3 problems >>> >>> Just sent the order go through the process. >>> >>> If you have issues, then, we can set about resolving for you and the >>> greater community. The new release has the new 16F180xx and 16F171xx >>> chipfamily - we are waiting on the 16F181xx to arrive before we can add >>> (as we have to test them!). Also, adding more PIC32Mxs at the moment. >>> Always busy. >>> >>> On Friday, 11 November 2022 at 17:59:56 UTC [email protected] wrote: >>> >>> Hi Evan, >>> >>> I noticed indeed issues with PICkitminus that it sometimes recognizes >>> another PIC than the one that is installed. >>> >>> So in order to get rid of this - and other issues I encountered - I just >>> ordered your PICKitPlus software for my PICKit3 🙂. >>> >>> Kind regards, >>> >>> Rob >>> >>> ------------------------------ >>> *Van:* '[email protected]' via jallib <[email protected]> >>> *Verzonden:* vrijdag 11 november 2022 07:51 >>> *Aan:* jallib <[email protected]> >>> *Onderwerp:* [jallib] Re: PICKIT 3 problems >>> >>> As the real developer of PICKitPlus and the database that was >>> plagiarized by PK- I am the right person to help. >>> >>> When our database was copied the developer decided to change the order >>> that the chip families are searched. I wrote a detailed analysis for him >>> and he ignored. So, using PK- can apply the incorrect voltage your PCB >>> during startup. >>> >>> Which chip or chips have this issue? This will help me isolate the >>> issue. >>> >>> Evan >>> >>> On Friday, 11 November 2022 at 06:43:29 UTC hans wrote: >>> >>> Hello all, >>> >>> I regularly have problems with the pickit-3.(MPlab X IPE v 5.45) . >>> >>> Because it happens less often when I first start up my PC, connect the >>> pickit to the PIC and put voltage on it and only then connect the USB >>> cable, this is my base. >>> >>> Despite this, I get often messages that the voltage is insufficient, >>> the PIC is not the right type or a wrong feedback occurs during >>> programming. This can almost always be solved by restarting MPlab, or by >>> first performing a read or an erase. >>> >>> Lately I've been working with 3.3V. Now I had a program under 3.3V and >>> that didn't work at all after programming without errors. After I erased >>> the PIC separately below 5 V, the program works again. >>> >>> I have two clones. One suddenly doesn't work at all under 3.3 V, but >>> with the Pickit_minus (with modified firmware) on 5V. >>> >>> Can anyone tell me where to look for the cause of all this? >>> >>> regards >>> >>> Hans >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "jallib" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/jallib/e74098b6-6d7d-45a6-ba6c-087cc51faadcn%40googlegroups.com >>> >>> <https://groups.google.com/d/msgid/jallib/e74098b6-6d7d-45a6-ba6c-087cc51faadcn%40googlegroups.com?utm_medium=email&utm_source=footer> >>> . >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "jallib" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/jallib/64b27e61-12c7-451c-85e4-5c743cb3b417n%40googlegroups.com >>> >>> <https://groups.google.com/d/msgid/jallib/64b27e61-12c7-451c-85e4-5c743cb3b417n%40googlegroups.com?utm_medium=email&utm_source=footer> >>> . >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "jallib" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> >> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/jallib/GVXP195MB16375063A36BD0B02383E0C0E6009%40GVXP195MB1637.EURP195.PROD.OUTLOOK.COM >>> >>> <https://groups.google.com/d/msgid/jallib/GVXP195MB16375063A36BD0B02383E0C0E6009%40GVXP195MB1637.EURP195.PROD.OUTLOOK.COM?utm_medium=email&utm_source=footer> >>> . >>> >> -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/1b7c9365-883e-415c-9945-0044164f365fn%40googlegroups.com.
