Rob, prior to throwing it away, plug it in a stanium foil for a while to short all pins together. Old PIC12F675 had this problem with address 0 and this was in a surprising way the cure.
Of course, only if you did not supply it at 220V, see the top right corner... http://www.voti.nl/wloader/index_1.html another one of my daughter's old drawings...:) On Fri, Nov 11, 2022 at 9:53 PM Rob CJ <[email protected]> wrote: > Hi Evan, > > Downloaded, installed it and it work for my PIC16F18857 (also programmed a > PIC 12F675 and works OK). > > I still get the error on the PIC16F18857 that it is not able to program > address 0x0000 (verification error) but I think the PIC died so not related > to the PICKit3 software. I will try with a fresh version. > > Thanks for the quick service. > > Kind regards, > > Rob > > ------------------------------ > *Van:* '[email protected]' via jallib <[email protected]> > *Verzonden:* vrijdag 11 november 2022 19:10 > *Aan:* jallib <[email protected]> > *Onderwerp:* Re: [jallib] Re: PICKIT 3 problems > > Just sent the order go through the process. > > If you have issues, then, we can set about resolving for you and the > greater community. The new release has the new 16F180xx and 16F171xx > chipfamily - we are waiting on the 16F181xx to arrive before we can add > (as we have to test them!). Also, adding more PIC32Mxs at the moment. > Always busy. > > On Friday, 11 November 2022 at 17:59:56 UTC [email protected] wrote: > > Hi Evan, > > I noticed indeed issues with PICkitminus that it sometimes recognizes > another PIC than the one that is installed. > > So in order to get rid of this - and other issues I encountered - I just > ordered your PICKitPlus software for my PICKit3 🙂. > > Kind regards, > > Rob > > ------------------------------ > *Van:* '[email protected]' via jallib <[email protected]> > *Verzonden:* vrijdag 11 november 2022 07:51 > *Aan:* jallib <[email protected]> > *Onderwerp:* [jallib] Re: PICKIT 3 problems > > As the real developer of PICKitPlus and the database that was plagiarized > by PK- I am the right person to help. > > When our database was copied the developer decided to change the order > that the chip families are searched. I wrote a detailed analysis for him > and he ignored. So, using PK- can apply the incorrect voltage your PCB > during startup. > > Which chip or chips have this issue? This will help me isolate the issue. > > Evan > > On Friday, 11 November 2022 at 06:43:29 UTC hans wrote: > > Hello all, > > I regularly have problems with the pickit-3.(MPlab X IPE v 5.45) . > > Because it happens less often when I first start up my PC, connect the > pickit to the PIC and put voltage on it and only then connect the USB > cable, this is my base. > > Despite this, I get often messages that the voltage is insufficient, > the PIC is not the right type or a wrong feedback occurs during > programming. This can almost always be solved by restarting MPlab, or by > first performing a read or an erase. > > Lately I've been working with 3.3V. Now I had a program under 3.3V and > that didn't work at all after programming without errors. After I erased > the PIC separately below 5 V, the program works again. > > I have two clones. One suddenly doesn't work at all under 3.3 V, but with > the Pickit_minus (with modified firmware) on 5V. > > Can anyone tell me where to look for the cause of all this? > > regards > > Hans > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/e74098b6-6d7d-45a6-ba6c-087cc51faadcn%40googlegroups.com > <https://groups.google.com/d/msgid/jallib/e74098b6-6d7d-45a6-ba6c-087cc51faadcn%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/64b27e61-12c7-451c-85e4-5c743cb3b417n%40googlegroups.com > <https://groups.google.com/d/msgid/jallib/64b27e61-12c7-451c-85e4-5c743cb3b417n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/jallib/GVXP195MB16375063A36BD0B02383E0C0E6009%40GVXP195MB1637.EURP195.PROD.OUTLOOK.COM > <https://groups.google.com/d/msgid/jallib/GVXP195MB16375063A36BD0B02383E0C0E6009%40GVXP195MB1637.EURP195.PROD.OUTLOOK.COM?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "jallib" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/jallib/CAM%2Bj4qvhaP3wX%2BwU98-6ySD6i_6oafcrMB6RQZdRatPH4GYTOQ%40mail.gmail.com.
