O so you've got the adapters already? If that's the case then just use that! Run them to your RCA ins, 3/4 or whichever pair and give it a try.
HTH, D!J!X! -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Andy B. Sent: Saturday, September 18, 2010 11:49 PM To: 'JSonar -- JAWS Scripts for Sonar discussion list' Subject: Re: [Jsonar] Getting rid of hum/hiss Gold plated. I don't remember what is under the gold. I want to say either zinc or nickle. I think it's zinc though. This is both for the 1/4 inch plugs and the RCA plugs. The 1/4 inch splitter is braided gold strands with some sort of interferance proof insulation on it. 6 feet long to keep things at a reasonable distance. -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of D!J!X! Sent: Saturday, September 18, 2010 10:27 PM To: 'JSonar -- JAWS Scripts for Sonar discussion list' Subject: Re: [Jsonar] Getting rid of hum/hiss You can get quarter inch feemale to RCA male adapters, or get cables that come with quarter inch males on 1 side and RCA males on the other. A pair of 2 or 2 single ones plugged into your splitter and going into the lt RCA ins would do it. If you've got good quarter inch cables already, then adapters would be fine, if not just buy the cables; sometimes these adapters can be cheaply made. HTH, D!J!X! -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Andy B. Sent: Saturday, September 18, 2010 9:56 PM To: 'JSonar -- JAWS Scripts for Sonar discussion list' Subject: Re: [Jsonar] Getting rid of hum/hiss So, use 1/4 inch to RCA adaptors and feed them to my 1/4 mono males? -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of D!J!X! Sent: Saturday, September 18, 2010 8:15 PM To: 'JSonar -- JAWS Scripts for Sonar discussion list' Subject: Re: [Jsonar] Getting rid of hum/hiss Since you are using a headphones amp, as is normal for these low-end keyboards, you should use your stereo splitter, and try to get male quarter inch to male RCA cables. I have some here that I use on my lt, guitar center sells them for about 10ft for about 10 bucks. The signal you are feeding the interface is not line-level, a bit hotter, so you need to watch your volume when connected to the card. But even then, you don't want to use those pre's for anything other than mic or guitars etc. So get a pair of quarter inch to RCA cables and hook them up to your splitter and go that route. HTH, D!J!X! -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Andy B. Sent: Saturday, September 18, 2010 6:31 PM To: 'JSonar -- JAWS Scripts for Sonar discussion list' Subject: Re: [Jsonar] Getting rid of hum/hiss Having a huntch it is either being over amped because of the xlr ins or the keyboard putting out some funky signal somewhere. Trying to eliminate the problem is sort of hard when you have 0 1/4 inch ins on the soundcard. Really couldn't see paying an extra $600 for 2 1/4 inch ins on a doc. The cable is new and in good shape. Guess the best I can try is putting RCA adaptors on the 2 1/4 inch mono ends and doing what DJX recommended. -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Chris Smart Sent: Saturday, September 18, 2010 6:08 PM To: JSonar -- JAWS Scripts for Sonar discussion list Subject: Re: [Jsonar] Getting rid of hum/hiss I would try getting the correct cables so you can eliminate the adapters, just to rule out one variable. If you can get balanced cables, that might get rid of the hum although it isn't a sure thing. If you have Sound Forge, one of the EQ plug-ins has a preset for removing hum that uses four stacked notch filters. Do you have the Sonitus effects with your copy of Sonar? If so, use the Sonitus EQ and set up narrow bands to cut at 60 HZ and multiples of 60, 120, 180, etc. I doubt you're just getting the fundamental at 60 HZ; usually there are some harmonics in there as well. But, before filtering with software, which might negatively affect the audio you do want to hear, try to figure out where the noise is coming from and correct things there, with better cables etc. Chris _______________________________________________ Find JSonar and Sonar FAQs, articles, guides and downloads at jsonar.org. Jsonar mailing list [email protected] http://jsonar.org/mailman/listinfo/jsonar_jsonar.org _______________________________________________ Find JSonar and Sonar FAQs, articles, guides and downloads at jsonar.org. Jsonar mailing list [email protected] http://jsonar.org/mailman/listinfo/jsonar_jsonar.org _______________________________________________ Find JSonar and Sonar FAQs, articles, guides and downloads at jsonar.org. Jsonar mailing list [email protected] http://jsonar.org/mailman/listinfo/jsonar_jsonar.org _______________________________________________ Find JSonar and Sonar FAQs, articles, guides and downloads at jsonar.org. Jsonar mailing list [email protected] http://jsonar.org/mailman/listinfo/jsonar_jsonar.org _______________________________________________ Find JSonar and Sonar FAQs, articles, guides and downloads at jsonar.org. Jsonar mailing list [email protected] http://jsonar.org/mailman/listinfo/jsonar_jsonar.org _______________________________________________ Find JSonar and Sonar FAQs, articles, guides and downloads at jsonar.org. Jsonar mailing list [email protected] http://jsonar.org/mailman/listinfo/jsonar_jsonar.org _______________________________________________ Find JSonar and Sonar FAQs, articles, guides and downloads at jsonar.org. Jsonar mailing list [email protected] http://jsonar.org/mailman/listinfo/jsonar_jsonar.org
