This is very odd. The "OSPF instance is not running" message makes me wonder if there's a licensing problem. I haven't been able to find anything on the Juniper web site...
Are you able to ping your Cisco router's FF80 address? What do you see if you run "monitor interface traffic fe-0/1/0" while you run your pings? Do you have any neighbors picked up by ND (show ipv6 neighbors)? Do you have any Firewall Filters attached to Loop0 that would block some traffic? HTH, Serge ----- Original Message ---- From: Ramesh Karki <[email protected]> To: Serge Vautour <[email protected]> Cc: [email protected] Sent: Thu, April 1, 2010 3:50:59 AM Subject: Re: [j-nsp] ipv6 routing Hi Serge, The M10i is running on ipv4 (bgp, ospf, including static)from beginning with neighbor Cisco routers, now the requirement is to add enable dual stacking (v4 and v6) routing like ospf and bgp on the same platform. I haven’t faced any vendor compatibility issues between them on ipv4. And still I don’t think the problem is by multi vendors. here, the output of M10i : run show interfaces fe-0/1/0 Physical interface: fe-0/1/0, Enabled, Physical link is Up Interface index: 129, SNMP ifIndex: 123 Description: Connected to Beetle for iBGP peering Link-level type: Ethernet, MTU: 1514, Link-mode: Full-duplex, Speed: 100mbps, MAC-REWRITE Error: None, Loopback: Disabled, Source filtering: Disabled, Flow control: Enabled Device flags : Present Running Interface flags: SNMP-Traps Internal: 0x4000 CoS queues : 4 supported, 4 maximum usable queues Current address: 00:17:cb:77:00:1f, Hardware address: 00:17:cb:77:00:1f Last flapped : 2010-03-15 11:23:26 NPT (2w3d 00:57 ago) Input rate : 126752 bps (22 pps) Output rate : 87384 bps (46 pps) Active alarms : None Active defects : None Logical interface fe-0/1/0.0 (Index 69) (SNMP ifIndex 127) Flags: SNMP-Traps Encapsulation: ENET2 Input packets : 31156647 Output packets: 18571460 Protocol inet, MTU: 1500 Flags: None Addresses, Flags: Is-Preferred Is-Primary Destination: x.x.193.0/28, Local: x.x.193.1, Broadcast: x.x.193.15 Protocol inet6, MTU: 1500 Flags: None Addresses, Flags: Is-Preferred Is-Primary Destination: abcd:3800:2:1::/126, Local: abcd:3800:2:1::1 Addresses, Flags: Is-Preferred Destination: fe80::/64, Local: fe80::217:cbff:fe77:1f run show version Hostname: host-m10i Model: m10i JUNOS Base OS boot [9.2R2.15] JUNOS Base OS Software Suite [9.2R2.15] JUNOS Kernel Software Suite [9.2R2.15] JUNOS Crypto Software Suite [9.2R2.15] JUNOS Packet Forwarding Engine Support (M/T Common) [9.2R2.15] JUNOS Packet Forwarding Engine Support (M7i/M10i) [9.2R2.15] JUNOS Online Documentation [9.2R2.15] JUNOS Routing Software Suite [9.2R2.15] run show ospf3 overview OSPF instance is not running run show configuration protocols ospf3 preference 110; area 0.0.0.10 { interface fe-0/1/0.0; interface ge-0/0/0.0; interface lo0.0 { passive; Cisco output : #show run | be ^ipv6 router ipv6 router ospf 200 router-id x.x.192.10 log-adjacency-changes #sh run int lo6 Building configuration... Current configuration : 157 bytes ! interface Loopback6 ip address x.x.192.10 255.255.255.255 ipv6 address abcd:3800::4/128 ipv6 enable ipv6 ospf 200 area 10 no clns route-cache end sh run int fa0/0 Building configuration... Current configuration : 264 bytes ! interface FastEthernet0/0 description *** iBGP peering *** ip address x.x.193.4 255.255.255.240 no keepalive duplex full ipv6 address abcd:3800:2:1::2/126 ipv6 enable ipv6 ospf 200 area 10 no cdp enable no clns route-cache end Thank you, On Thu, Apr 1, 2010 at 3:26 AM, Serge Vautour <[email protected]> wrote: > Hello, > > Can you post the following to the mailing list? > > -show int ge-0/0/0 > -show version > -show ospf3 overview > > From the Cisco router: > -The interface and OSPF config > > I'm assuming IPv4 ping works over the interface? > > > Thanks, > Serge > > > ----- Original Message ---- > From: Ramesh Karki <[email protected]> > To: Antonio Querubin <[email protected]> > Cc: [email protected] > Sent: Wed, March 31, 2010 4:54:29 PM > Subject: Re: [j-nsp] ipv6 routing > > Hi, > Similar ospf config between cisco to cisco is okay there is not any issue. > But between cisco to M10i is not working. > Here, I have listed my JunOS ospf config : > run show configuration protocols ospf3 > preference 10; > area 0.0.0.10 { > interface lo0.0 { > passive; > } > interface ge-0/0/0.0 { > metric 10; > > am I missing anything ?? > > My curiosity : when I execute the command > run show ospf3 interface > ge-0/0/0.0 it says - > “OSPF instance is not running” ?? > > Thank you, > > > On Thu, Apr 1, 2010 at 1:12 AM, Antonio Querubin <[email protected]> wrote: > > > On Thu, 1 Apr 2010, Ramesh Karki wrote: > > > > I have also tried to run ospf3 but no luck, the command > show ospf3 > >> interface ge-0/0/0.0 says > >> “OSPF instance is not running” > >> > > > > I have tried run ospf3 but no luck, the command > show ospf3 interface > >>> ge-0/0/0.0 says > >>> “OSPF instance is not running” > >>> > >> > > What does your ospf3 config look like on the M10? What does it look like > > on the Cisco? > > > > > > Antonio Querubin > > 808-545-5282 x3003 > > e-mail/xmpp: [email protected] > > > _______________________________________________ > juniper-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/juniper-nsp > > > > __________________________________________________________________ > Yahoo! Canada Toolbar: Search from anywhere on the web, and bookmark your > favourite sites. Download it now > http://ca.toolbar.yahoo.com. > _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp __________________________________________________________________ The new Internet Explorer® 8 - Faster, safer, easier. Optimized for Yahoo! Get it Now for Free! at http://downloads.yahoo.com/ca/internetexplorer/ _______________________________________________ juniper-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/juniper-nsp
